1999 ranger, 2.55 speed. truck idles with very high rpm's when driving and shifting gears. have changed the AIC, mass air sensor. Throttle position sensor and still does it. the AIC has been changed 5-6 times in 6-8 months as parts store kept telling me it was that. What can i look at, check, etc...
View 6 RepliesSo my "farm truck" is idling very rough, to the point that sometimes that it stalls out. At high idle it runs fine but when its at a idle its very rough. Its been running fine until probably a month ago or so and its just getting worse. What it could be? I am thinking it might be that something is dirty but i just dont know where to start with figuring out what the problem is.
View 9 RepliesMy ranger has a 3.0 v6 engine it idles high and accelerates on its own sometimes. Sometimes its more often then others. I turn my key about three times thinkin its reseting the computer and stop it and it does. But I keep hitting a dead end and don't know what to do about it.
View 10 RepliesMy son just purchased a 1996 Ford Ranger 2.3l 5 speed it is a nice little truck. But I have a question when you press in the clutch it acts like the choke has come on it idles way to high. When you come to a complete stop it is a few minutes before it goes back to its regular idle. Is it suppose to do that?
View 9 RepliesI now have a 1991 ranger 3.0 super cab. I need a step by step walkthrough of how to time it. Keep in mind that I ha the distributor out while turning the engine over so I need from start to finish, including the spout connector. It runs right now but idles high at the start and the. Stumbles down to about 500rpm and sometimes dies....
View 12 RepliesWhere to start looking to resolve this code. It is not an intermittent code. It returns after about 3 to 4 key turns. Truck idles a little rough but runs fine. I have looked up the code and causes but wondering how to deal with this directly and fixed it. I'm wanting to sell my truck for something bigger and would like to solve the issue before hand. 2003 Ford Ranger Edge...
View 4 RepliesI have a 96 ranger with the l4. Right before I bought my newish truck last December, it's started miss firing and running really bad. I replaced the spark plug wires, most of the spark plugs, and both coil packs. Didn't work at all. Then I bought my new truck and parked. Fast forward to now. Fired it up, ran REALLY bad. We changed the wiring order from the 96 order to the 99 order.
But the truck idles from 500rpm (barely running) and randomly jumps up to 2-3000rpm and then back down. Driving it has NO power, rev it and it stays at 2-3000 for quite awhile. Sometimes it randomly dies. REALLY need to get it running quick and cheap. Getting ready to sell my daily driver to find something else and I need something to drive while I hunt for another truck.
I am having a problem with my O/D light flashing and my truck shifting hard. Just started out of the blue. After reading a few other topics, I am hoping it is the VSS. Now if only I could find the dang thing. Looking for a diagram, or detailed description on where it's at?
View 14 Replies1999 B3000 with a 3.0. The truck idles at 850rpms. When it starts it idles at around 1000 and runs very rough. When I disconnect the IAC the engine dies. The AC also has problems it blows cold at idle but at highway speeds after 7-8 minutes running the compressor kicks out. One can turn it off and it blows cold again after a few minutes.
View 5 RepliesTwo days ago, I was driving on a North GA steep, windy, mountain road in my 2002 v6 4.0 Ranger. All of a sudden, i started revving real high (about 4000rpms) and getting no power (20mph). I pulled over immediately and transmission fluid was pouring, by the quart, out of my truck. I didnt get to look exactly where it was coming from, since i backed away once i saw a small flame coming from the leak. i then called a tow truck (assuming it was a seal or a hose break) and had it towed to my house.
I started investigating the possible problems and didn't really see anything noticeable under the truck (not that I was expecting to). So what I did was put three quarts of transmission fluid in the dipstick hole and put in gear to see if I could spot a leak. nothing. then I drove it around the block to get it warmed up and put a little pressure on the transmission by driving up a semi-steep hill to see if that would spark the leak again. still no sign of the a leak.
And finally, when I went to go check the dipstick after my test drive, it read to be above the cross hatched area, hence being overfull. What my next step should be?
1994 FORD RANGER stalls while driving - differant speeds ...differant miles ...no rhyme or reason to it - cranks right back up ...can even pop clutch and cut it back on. Already replaced Ignition Start Module - Dpes sensor - temp sensor - and scan shows all codes are clear and truck passes. We are clueless to whats causing this. 4 cyl 2.1
View 12 RepliesThe problem : I bought a 2004 Ranger truck and after two days it started to hiccup, or stall or die while driving, then because the truck is manual, just start up and keep running. It was the strangest thing.
I gave it to a shop, and after checking the electrical, the ignition, the fuel system, the drive train, and ten hours of troubleshooting, they came up without an answer. So they gave me the truck back.
Answer, a few days after taking it back:
I had told the shop that it had been sitting for 6 months, May till January, but when I told a mechanic friend a bit later, he still suggested 2 bottles of gas line antifreeze in the tank, before the next tank fill. I did that, and there was some improvement.
Next, When I replaced the balding tires with new Nokian Winter tires, the tire shop, (Kal Tire), told me that the air cleaner was incredibly dirty, and asked me if I would like them to replace it. I said yes, thinking that it might just do the trick, as no one in the forums I read, had mentioned it.
Success! No hiccup or stalling and it has not died since.
I have a 92 ranger 6cyl 4L. The truck stopped running while driving then kicked on again, it did this several times over about 20 minutes then finally died and now I can't get it started. I recently replaced the fuel pump and filter and spark plugs and wires. I get spark if I ground the plug and some gas will pour out of the fuel pressure test valve when I stick a screws driver in. When I check engine codes I get an all pass. Truck will turn over and sometimes run for 2 or 3 seconds but that is it.
View 2 RepliesWhat would cause my 4x4 high and 4x4 low lights to flash intermediately together on cold mornings while driving? It won't switch into 4x4 when it does this either. When it sits and warms up later in the morning all works as should. It doesn't do it all the time but when it does its annoying not to mention it's sucks when I need 4x4.
View 1 RepliesIf I don't keep in the throttle immediately after start up it will stall a lot of the time. It doesn't do this every time or if it sits for a while but if I drive it and then stop off at a store or something and then go to start it back up it gives me this problem. I notice it idles about 3-4k RPM's when I stop at a light or something too.
View 14 RepliesSo I've been having this issue for a while and I think I know what it is, just wanting to confirm it is the problem before I go fixing it. My car idles at high RPM's, at around 1-2k when I am sitting at a stop sign or stop light. I replaced the MAF sensor but that wasn't the issue. I assume that it is the throttle body or the sensor.
Also, I came out the other day to park my car in the garage and I saw a huge puddle of water where the passenger puts his/her feet. It was all in the carpet and I just dried it up. It was raining out but I don't think I have a leak or anything. I was told it might be my heater core that went out and that the AC is the problem.
I just bought a 1991 F150 with a 302 (5.0). It idles at around 2600-2800 RPMs. The previous owners replaced the TPS and IAC, but it still idles fast. Ford dealership told them it was a vacuum leak. Are all the vacuum lines close to each other? How easy is it to locate/fix the problem?
View 2 RepliesFord Ranger 20012.5L
Manual 4 Cylinder4x2
Drivetrain~150K Miles
The problem with the vehicle is that it won't shift into gear easily and smoothly. It started occurring just this last Friday or Saturday (2011-06-24 or 2011-06-25). I was driving around 35 MPH, slowed down to a stop at an intersection, and when I put it back into 1st Gear to begin driving, I had extreme difficulty shifting the gear.
I cut the ignition and started again, was able to put it into 1st Gear and made it home by coasting (getting into any of the other Gears was just as difficult, fortunately I was in the neighborhood). Following this, I tested it while parked the next day. Same issue. Then I tried double-clutching, which seemed to work out, but I only did it parked, since I didn't want to strand myself on a road (I'll take that risk when I go to a mechanic, though).
I've read this [URL] ...., I'm pretty sure it's the clutch (master/slave cylinder) and I'm also aware that it could be the transmission fluid requiring a change. I haven't changed the transmission fluid at the 60K & 120K interval per Ford's suggested maintenance schedule (I got it around 50K-60K from a dealership, so I'm not sure if they may have done it preemptively).
A couple other details. For the past year or so, I've been driving 100 Highway miles for 4-5 days a week, for work (50 to work, 50 back home).
Are my assumptions right, or is it possible that my whole Transmission is getting ready to go? Are there any other details I should provide?
96 Ranger 2.3 5 speed, 2wd. 212k on the clock.
Bought this from my BIL last week. CEL was on so I ran the codes. replaced the air filter, cleaned the MAF (with CRC MAS cleaner), replaced the EGR solenoid (physically broken). The first code showed this was throwing the code. That code (p1409) went away but p0402 showed it's head. replaced the DPFE sensor, disconnected the battery for an hour and am now code free.
Now it idles like crap, up and down with A/C on or off to nearly dying and does eventually die. Disconnected the MAS and no change. Cleaned the AIC no change, replaced the AIC with no luck. Checked for any obvious vacuum leaks around items I messed with. Found nothing. With engine running I disconnected the vacuum to the EGR valve and idle smooths out. Feel a small vacuum tug from the hose, nothing at the valve.
Haven't changed the PCV or cleaned the throttle body. Could it be the EGR valve since removing the vacuum seemed to work?
Side note, BIL's mechanic told him THREE YEARS AGO the CEL was 'probably a O2 sensor' and that is doesn't do anything and no need to fix.
Still no codes and still no power. Can't hear any vacuum leaks. Bought new plugs and wires but haven't installed them yet. EGR? TPS?
I'm having a bit of trouble with my fathers '03 Ranger Edge 4.0L. It has about 100k miles on it, and we keep it very well maintained. This is the first major problem we've had with it.
When the problem first occured, it had been driven about 30 miles on the highway and about 5 miles after getting off the highway, he pulled up to an intersection and stopped. As he started accelerating again, it all of a sudden started sputtering, surging (almost exactly as if it were running out of gas), and then stalled. It continues to exhibit this behavior. It will start and idle fine, but struggle and then stall when given any amount of throttle. It's also an automatic transmission if that makes any difference.
Fast forward to this past week after we had it towed home. We have checked the fuel pressure, and its dead on at about 64psi. We changed the fuel filter, changed the PCV valve, changed the upstream O2 sensor, put in a new air filter, cleaned the MAF sensor, and cleaned the intake of the throttle body. We're now at a loss as to what could be causing the problem. The CEL is not on, and there are no codes being shown when we plugged it in. We also thought it may have been bad gas, so we drained the tank and put fresh gas in from our preferred station. The plugs and wires are also fairly new, only about 4k miles on them.
Are we missing anything here? What else we could try? The absolute last resort is taking it to a shop, we're going through a rough patch with finances.
I have a 5-speed transmission pickup (’04 Ford Ranger EDGE SuperCab). Clutch pedal feels "normal", No resistance when shifting gears. Will go into gear with ease, except for 2nd gear (grinding noise), must push clutch to the floor and still grinds; but only 2nd gear. In 1st gear, my truck will slowly creep forward as if unable to engage and not having any kind of pulling power. Even when shifting to 2nd, 3rd, 4th and 5th gears, it barely maxes out at 30MPH (top speed unless vehicle is on a slope or slight decline then I can get up to and over 40MPH. Checked brake fluid level, it’s ok. The fluid’s at max. Clutch is relatively new (April 2014), with only about 13,000 miles on it, if that. It must be cylinder issue. Is there any way to tell whether it's the clutch master cylinder or slave cylinder?
View 5 Replies