Ford Ranger / B-Series :: Transmission Swap From 1996 To 2000?
Feb 26, 2013
Will the transmission from a 2000 fit a 96? They're both 3.0's.
View 3 Replies
Feb 26, 2013
Advertisement
Ford Ranger / B-Series :: 1996 - Transmission Slipping When Cold
I have a 1996 Ford Ranger with 95k miles on it. Recently, my truck's automatic transmission has been slipping really bad. I'll be driving down my road and while going around a turn, the clutch feels like it randomly disengages, so when I press on the gas, it feels like I'm revving my truck in neutral, and then it will all of a sudden get back into gear, violently a lot of the time. However, once the truck is warmed up, the it runs perfectly and never slips. I've checked my oil multiple times and even changed the oil filter in the transmission. I am not sure if this has anything to do with it, but if I let my truck idle in park for a little bit, the RPMs will increase and if I shift in to reverse or drive while the RPMs are high, it'll do the same thing.
View 14 RepliesFord Ranger / B-Series :: 1996 - Transmission Grinds When Putting It In Reverse
I own a 1996 XL Ford Ranger 2wd 5 speed manual.
Last week I had it in for some service, which included bleeding the clutch lines and new fluid.
Since then when putting it in reverse the transmission grids. It is also very difficult to get into first gear - I really have to shove hard on the stick.
Better Description of symptoms: When the vehicle is moving it shifts fine. When I come to a stop, put it in neutral and let out on the clutch, it is then very difficult to get back into first gear. If I leave the clutch in, fter I come to a stop, I can shift around to all the gears no problem. It's only when I let out on the clutch, then push it back in to shift into first is the difficult part.
With reverse, I have to move ahead a bit, THEN I can shift to reverse without the grinding noise. I talked to my mechanic who check to ensure the fluid was NOT low (it wasn't) and no air bubble existed in the line. After that was checked, he said the clutch is worn and has to be replaced.
Well, then, why wasn't it doing this BEFORE I had him bleed the lines? It started the day I picked the truck up from service. He recommends the following to fix the problem...
- slave cylinder
- new line
- disc
- preasure
I am asking why this would happen after he bleed the lines? Is there another problem that can cause this?
Ford Ranger / B-Series :: 1996 Automatic Transmission Not Shifting - No Reverse / Drive Or OD
So here in Wisconsin for the last two weeks we have had nothing but ice. That being said, I have a '96 ranger 3.0L, automatic transmission, 4x4. 4 wheel is inoperable at the moment, that's a different story. Here's my question: with the ice, there has been a lot of tire spinning at high RPM's, the other day, I was again stuck on the ice and rocked back and forth had some pushers, thought we were getting somewhere but I went to shift gears and all of a sudden had nothing. No Reverse, Drive, OD, L, 2. Did I blow my tranny? There was no noise or grinding, but the OD light seems to blink. Is there something I can check or look at?
View 4 RepliesFord Ranger / B-Series :: 2000 XLT - Transmission Slips When Starting From A Stop
2000 Ranger XLT 4x4 3.0L Auto
So a couple months ago I had a transmission problem. It shifts high and hard all times and after the "od" light gets going (after it gets warm), the transmission slips (like riding clutch) when starting from a stop. If I went from drive to 1st gear with the selector and back, it cleared the slipping problem for a bit. I did an oil/filter change and about 50 miles later the truck is running fine, no issues. One day I hopped in it to go to work and it was like nothing ever happened. Fast forward 1,500 miles later. I start to notice the transmission is subtly shifting weird, like a small jerk when shifting. It gets worse over 50 miles and now I am back to the above problem. Is there a way this could be a sensor or solenoid problem? I never heard of a transmission correcting an issue then starting at it again so much later.
I don't like fixing or working on an issue unless I am at least 95% sure what the problem is. I also don't have $2k to plop down on a repair at the moment. Would it be worth it to take this to a dealership and see what trouble codes I am getting? I would try a transmission shop but it's not guaranteed they will have the test equipment to check a ford transmission. Also a friend said that AutoZone and other stores can't check transmission codes. So what's the best option here?
Ford Ranger / B-Series :: Can Swap To One Piece Driveshaft?
Can I swap my 2 piece out for a one piece in my 88 ranger supercab? It is a 4x4 5 speed.
View 8 RepliesFord Ranger / B-Series :: 2000 - ABS Light / No Speedometer And Transmission Doesn't Want To Shift
Sold my mazda and got a nice 2000 2wd Ranger XLT with a 3.0L. Today the wife I and took it to town, 10 miles on the highway there, a couple in town and 10 back, didn't notice anything unusual. However I haven't this truck long so I'm not sure what is usual.
Parked it for a few hours and when went out to change the front turn signals to LED I noticed the ABS light was on when I drove it into the garage...
I checked fluid, connections and fuses, no change.I go ahead and swapped the bulbs while letting things simmer, I've had so many of these Fords sometimes the easy fix comes to me.
I backed it out and took it down the road, right away I noticed my speedometer wasn't working, so I let off the gas, when I re-applied the pedal I got nothing, like it was in neutral.
I downshifted to second and got her down and turned around as the O/D started flashing... (so glad because I would have hated walking back), then pulled her back in the garage to check transmission fluid and recheck fuses, including the ones I forgot earlier under the hood. I added a 1/4 qt of fluid then tried a road test again, this time there was a real long pause before it upshifted hard and the CEL came on.
I pulled the codes with my scangauge and got:
P0500
P2120
P0028
And decided I better look some things up and consult the gurus here before I do anymore damage tonight. I'm guessing that I'm looking at a tranny replacement possibly, but with the ABS light and speedometer failure I'm not 100% sure what is going on here...
Ford Ranger / B-Series :: 2000 / 4R44e Transmission - Hard Shift From 2 - 3 Gear
2000 Ranger 4R44e transmission.Hard shift from 2-3 gear and when i run about 35-40 mph and brake then acelerate it downshifts hard . Whats wrong with it?
View 14 RepliesFord Ranger / B-Series :: 2000 - Automatic Transmission / Tuck Will Not Go Forward In 1st Or In Drive
I have a 2000 ranger 3.0,automatic 4x4.The truck will not go forward in drive 1 or in drive. If I start out in second gear it will shift through the other gears. What the problem is?
View 6 RepliesFord Ranger / B-Series :: 1991 - Tranny Slipping / Swap Options?
1991 Ranger 4.0L A4LD... Its a 4x4. ext cab
What else will bolt up to this 4.0L? Could i put a 4R44E/4R55E tranny? Is there a good stick that bolts up?
Ford Ranger / B-Series :: Door Swap From 1992 To 1993 Model
Will a driver door from a 92 ford ranger fit a 93 ford ranger?
View 5 RepliesFord Ranger / B-Series :: Motor Swap From 1994 To 1987 Model?
I have a 1987 ford ranger, it has a 2.0L carborated motor and I also have a 1994 ford ranger fuel injected motor I believe it's a 2.3L, I am wondering if the swap will work to put the 94 motor in the 87....
View 3 RepliesFord Ranger / B-Series :: 1994 - 3.08 Gear Swap To 3.55 Effect Power?
Im wanting to get more power out of my 94 auto supercab but I don't wanna kill mpg it has 3.08 gears I was thinking swap to 3.55 to keep mpg would there be noticeable power difference?
View 6 RepliesFord Ranger / B-Series :: 2001 - Engine Swap / Knocking Noise For A While
I have a 2001 ford ranger 2.5 and a standard 5 speed. Its been knocking for a while now and recently its made a much lower tone knock, I am thinking I may have thrown a bearing. Also I am wondering what other engines I can use, besides the 2.5.....
View 3 RepliesFord Ranger / B-Series :: 1986 - Diesel Swap - Engine And Trans Combos?
I have A 1986 ranger with a 2.9 v6. I am thinking of doing a diesel swap and I am wondering what engine and trans combos would work best for this. I was thinking 4bt but there are may other options that could work.
View 14 RepliesFord Ranger / B-Series :: 1996 XLT - ABS Not Communicating
My 96 ranger had lost a brake pad coming out of the mountains. I replaced the rotor but the ABS light came on as well as the check engine within a week. Several issues the clock spring was bad, replaced. The cam position Sensor was bad, replaced. I had this at a shop in a small town. While I was there they ran diagnostics.
At first the ABS module was sending data and gave them some info. Suddenly there was no more data stored in the module. They ordered a new ABS module installed it and replaced the LF sensor cable. Both sensors were cleaned prior to this.
The new abs module required a trip to ford to reprogram. At the shop they still could not get the light out. I took the truck home to my ford dealer and they said bad abs. Got a new (rebuilt Mfg discontinued) Installed and ford said this was bad with a code c1102. 4 w 4wd installed needs 4 w 2wd. ordered a new abs. Ford said same code again and the tech said that the ABS is not communicating through the obdii port.
My thoughts are the reader they used at the small shop was defective and either shorted out something or blew a fusible link. I am told this is 4 wheel abs with the rear sensors are on the pumpkin but after looking at the diagrams I do not see a RABS fuse. I have tested all fuses, and the shop replaced several relays. The pcm and ABS diodes check ok. Perplexed.
Ford Ranger / B-Series :: 1996 - Ignition Coil B Went Bad?
My engine has 2 ignition coils, and b went bad, but which one is b. ?
View 9 RepliesFord Ranger / B-Series :: 1996 - Won't Start And Crank Even?
I have a 1996 Mazda B2300 & I heard that it is similar to the Ford Ranger.
Well the thing won't crank or start.
This is what I have done so far. I wanted to put a RPM meter on it. I followed YouTube videos on how to do it. I cut the Tan wire w. the yellow stripes & try to connect the wire to thr RPM meter. Then it won't start soo idk what to do. I also took put the PCM too. (I was looking for the wire) Now be honest, I talked to a mechanic, he said thag I might have blown my PCM or Blown another fuse. But when i put the key in to crank, it won't start ot click at all. The lights come on & it wants to start but won't start.
Then my mechanic tried to start it by the... Idk what it is called but you can start it & it wont evet start. It will crank like crazy but will not start at all.
Ford Ranger / B-Series :: 1996 - Putting SB In Place Of The V6?
I have a 96 Ranger 3.0 auto that is hitting 300,000 miles. I've got a 302 that i build for my F150 but know i'm thinking of transplating it in the Ranger. Is it a big deal in putting a SB in place of the V6.
View 4 RepliesFord Ranger / B-Series :: 1996 - No Heater Control
I seen on this site awhile ago something about a fix for the heater control door, I have a 1996 Ranger and all I have is Hot heat and cannot cool it down with the temperature control.
View 2 RepliesFord Ranger / B-Series :: 1996 - Power Steering Replacement
I'm in the middle of replacing my pump. With the new pump are a plastic washer and a small rubber o-ring but no instruction where they are supposed to go. They didn't know at auto zone and I haven't heard them mentioned on any youtube video. I found a crushed torn up washer similar to the plastic one in my catch pan. Maybe it is supposed to go in around the high pressure hose connection.
View 6 Replies