Ford Ranger / B-Series :: Throttle Stuck Open Causing Truck To Move Forward When In 1st Gear
Jul 26, 2012
Have a 99 Ranger XLT, 4 cyl, manual transmission with 191K miles. Was running good as ever last night but went to start it this morning and throttle's stuck open, causing truck to move forward when in 1st gear. Even with clutch in, near impossible to get vehicle in or out of gear. Managed to get it into reverse, but truck was having none of it. What is the cause or causes of my trouble? Or how much the repairs might cost? I'm on the road so no chance of doing this myself.
View 2 Replies
Advertisement
2000 ranger v6 automatic trans electronic 4wd shift on the dash. Plowing snow all of the sudden lost both forward and reverse never slipped or made any noise. Transmission fluid is fine to the level and clean. Put in drive nothing and reverse nothing put it back in park you can hear the park paul trying to click in. Towed it back to the shop thinking maybe the transfer case was junk. Decided to check the actuator on the transfer case no power going to it, go back to the switch no power there either check the fuses both are good and have power. The question i have is could a bad GEM module cause all this? ps the windshield wipers do work.
View 6 Replies
Last night I backed up out of a parking space and when I put it in drive it wouldn't move. It seemed like the transmission was locked up. What happened? The truck was running fine. It's a 2002 Ford Ranger 3.0 with auto transmission. Getting it serviced? I'm tempted to go to a dealer. What the problem is? Repair costs? The fluid looks good - no burning smell.
View 5 Replies
I think a fuel injector is stuck open on my 97 Ranger 3.0. How can I check to see if I'm right and which one it is? I've heard about the "listening to the injectors" trick but I'm not sure what procedures to go through. Can I tell if one is open by taking them out and visual inspecting?
View 9 Replies
2002 Ranger 2.3L, 5 spd, 108,000 miles
This has been from about 10,000 miles now. I have cleared the codes, sometimes it will go away for a day or two, but usually is back almost immediately. Finally last week I removed the solenoid and two vacuum lines hoping I would find a cracked hose like others have. No go there, but I replaced the vacuum lines anyway and dosed the vacuum ports on the solenoid with a little carb cleaner. Started truck up and revved it a few times, light stayed out. Next morning the check engine light was back on again.
Guess it must be in the actuator or the IMRC itself. Any success story about using some kind of cleaner to try to degunk this first (assuming it is stuck, that is...) without having to tear it apart?
View 8 Replies
I bought the 94 B2300 from a guy that said he got it from an auction and didn't know much bout it. Got 30 mins down the road and went to down shift to 4th coming into town and all I got was grinding. Turned it off and it would go into other gears and start in gear with the clutch pushed in. Wen I tried to take off it wouldn't move and just died. Towed it home and installed a new clutch kit in it. Got the clutch bled and went to test drive it and now it is stuck in 1st gear. Can it be easily fixed or am I going to have to replace the transmission...
View 3 Replies
What should the idle be at for a 2004 f150 fx4. When I first start the stuck it jumps to about 1200 or so and then after a few seconds settles at about 500 and stays there at all stops. It seems to be smooth but when I let go of the brake, the truck doesn't really want to move forward. It is a crew cab so I know there is some weight there. If anything is wrong, what are some possible fixes.
View 3 Replies
I have a 98 ford ranger with a 3.0 v6 it has 228,000miles standard tranny but I keep the truck running great. I did the plugs and wires about two weeks ago and it was running fine, actually great. This morning I got into the truck to start it this morning and it barely started. It fired up but barely stayed idling. I would get into the petal and it wouldn't raise rpms. I had to get to school so I headed out. I couldn't get any speed in gear the truck wouldn't gain speed. It would sputter and pop and then all of a sudden it would go ok but then start popping again. I took it to a buddy shop and his scanner showed p1131 and p1151 both codes. I don't know what to do?
View 13 Replies
Before I got my GX someone posted they had to press harder on the brake to keep the vehicle from moving forward. My truck idles at 550 rpm and the vehicle will barely move forward even with NO brake. Just resting my foot on the brake will hold it easily.
View 6 Replies
So my sunroof is stuck open and the shade is all the way forward. When I try to close it the glass touches the shade and then goes back to the open position..
View 1 Replies
A friend of mine at work has a 93 4wd explorer. A4ld transmission. Reverse quit working, and no matter what gear you put it in, reverse, neutral, or park, it will stay in drive. Park holds itself, but if you give it gas, it tries to pull. He says when it's in reverse, it's almost like it's stuck in reverse and forward, it wants to rock. He pulled the pan, no metal shavings, and pulled the valve body. He said the screws holding the valve body were finger tight. The gasket underneath had a small tear in it, he doesn't know if he did this pulling it out or not. He replaced those gaskets and retorqued the valve body. When he put it in reverse and topped off fluid, reverse worked. He put it in drive and it worked, but when he put it back in reverse, it stayed in drive and is staying in drive in all gear selections again. He bought this explorer new, and the transmission had never been into before.
View 3 Replies
My buddy has 2005 Ford Ranger, 4.0L V6, manual with 4WD. It cranks fine, shifts through gears, but it will not move. We're thinking something to do with the parking brake, but I don't have much knowledge about brake systems. A cursory inspection showed a cable without much rust, some rust on the rear drum brakes, and around the mounting where the brake cable runs into the brake drum. I can pull downward on the cable about three inches, so it doesn't seem like the cable is pulled too taut. The pressure on the brake pedal feels about normal.
(edit: something sort of important I forgot to mention, which is why I don't think it's the transmission. In neutral, we cannot push the truck. When pushing from the rear, it will rock back and forth a few inches. When pushing from the front, the truck will not budge at all with two guys pushing on it.)
What sorts of tests can we do to pin down where the problem lies? If it is the parking brake, how can we loosen it up enough to get the truck moving to a shop (or at least to the garage where we can get to the brake shoes)?
View 17 Replies
The gear shift works fine, and we lifted the hood and saw that the mech. arm IS working when we shift. However, the van will not move into any gear. won't go forward, reverse, etc... it acts like it isn't shifting.
i was driving down the highway, and noticed it wasn't accelerating and stepped on the gas.. .and nothing. I stopped the van, put in park, turned it off. Started it again, and put in D and wouldn't go, just engine revved. then put in reverse and same thing... didn't move but engine revved.
View 3 Replies
I have a 2004 2.0L Jetta with a 5 Speed manual transmission.
When shifting into third gear sometimes I push the shifter forward and it does not want to move all the way forward. It feels like I am pushing the shifter knob against a wall, or more accurately the bottom of the shift that pulls the cables feels like it is hitting a wall. If I pull it back out and press it in hard it will go into place sometimes.
This also solves the problem: While the shifter is mid shift into third, at the wall/ at the point of resistance, I let off the clutch slightly to give the flywheel some friction. This rolls the transmission a bit and allows third gear to slide into place.
I have experience with a MK4 Audi TT 1.8T that cam with a 6-SPD and it at had a 1-2 and 2-3 synchronizer issue (The one where the nipples are worn and it grinds at higher RPMS because they can no longer make a firm handshake). The issue I am experiencing is not that.
Could it be the transmission cables? Could it be some other cogs in the transmission? - If so does this mean I need to buy a used one? My car has 180K miles on it with the original clutch.
View 5 Replies
Will move if n 4low and give some rpm's. Reverse is fine, disassembled and clutches look fine.
View 1 Replies
My emergency brake works fine when I am parked nose down; it prevents my truck from rolling forward. When I'm parked nose up, the e brake doesn't stop the truck from rolling backwards. 2.3L 1993 ford ranger manual trans.
View 3 Replies
I have a weird issue. When I'm running AC on my 2.3l ranger sometimes the idle wont go down but rather hold its current RPMs till i either turn the AC off or place the truck back in gear. What that could be?
View 6 Replies
I have a 2000 ranger 3.0,automatic 4x4.The truck will not go forward in drive 1 or in drive. If I start out in second gear it will shift through the other gears. What the problem is?
View 6 Replies
My 4x4 4WD Ranger has a 5 speed manual tranny that locks up after going forward a few feet. It can back up all day long but locks up going forward. some god awful noises (grinding, clunking, etc) come out of that gearbox. the 4wd is electrically operated. the ? is , can this tranny be rebuilt with a kit? I'm having great difficulty finding a replacement. Are bronco II's compatible? Engine is 2.9L V6. On disassembly I found 2 meshing gears with broken teeth.
View 5 Replies
About, one month ago my car shut off while driving(pretty scary at the time). I pulled of the road and attempted to start it again. Everything looked good there, but as I was making my way home from work it started to act funny. It would not acknowledge me depressing the accelerator. When I got home, I ate supper, then went to have a look.
The car would turn on, but not acknowledge me pressing the accelerator at all, It did however go up to 30 mph at a snails pace as if it was coasting down a hill. I plugged in my code reader, and it read that the Throttle Body Valve was stuck open. I took it off and tore into to it a bit. I noticed the gears inside the TB itself were corroded and the butterfly valve was locked up.
I replaced the part, and tried to turn my car on with the new TB. All the dash lights are in working order, however upon turning the ignition to crank the engine, the whole car system shuts down. No lights no nothing, besides the car door open sound. The car will remain like this regardless of the key position until I have reset the batter(take off the terminals and put them back on) to which the process repeats itself.
The code reader says no codes are stored because I obviously reset the battery. So now am at a standstill.I believe the old TB froze up, because I had to run in through 3 ft standing water during a storm, and then deployed shortly after(I'm in the service) for a few months while letting the car sit.
View 1 Replies
We have a 98 Honda Civic that recently developed a problem with the throttle getting stuck open. With the engine off, the throttle will return to the idle position. However, with the engine is running, when the accelerator pedal is pressed, the engine revs increase, but then do not decrease when the pedal is let off. The same thing happens when the throttle is manually opened (not using the cable) with the engine running. The valve for the air intake doe not seem particularly dirty. I cleaned the spring assembly which I initially thought was the problem. The car is sitting the the driveway with both of us moderately terrified of driving it?
View 12 Replies
