Ford Ranger / B-Series :: Temp Gauge Hardly Moves At All
Dec 21, 2013
I have a 94 Ford Ranger, 2WD, 5-Speed, with 2.3 engine. My temp gauge hardly moves at all... It actually appears as if it doesn't move it you don't pay close attention and were to just glance at it. I'm thinking it is most likely the temp sensor that is on the engine block as I understand there is also one that is in the line that controls the fans for the radiator. Am I approaching this in the right direction or is there something else I might need to do?
View 3 Replies
Advertisement
My 94 Ranger 3.0L 5speed 2wd temp gauge is staying on the cold side but the heater is working good and I used a laser pointing thermometer at the thermostat housing and got 180* after running for a while and I also noticed that the fuel economy had gone down along with the power. I was getting 340 miles to a tank but now I'm getting 280 per tank.
View 12 Replies
Water temperature gauge doesn't work. Assumed the problem was the sensor so bought a new one. Installed it, still nothing registering on the gauge after I know the water is heated up (drove it for 45 minutes, heater blowing hot).
So crossed the ground on the sensor and the gauge shot to the top so gauge is working.
Pulled wiring diagram and that sensor is SUPPOSED to register 79ohms for cold and 8 ohms for hot.. So bought a 10ohm resistor from radio shack and attached the water temp lead to it and the gauge read correctly about 1/8 inch from the H mark on gauge. This confirmed for me that gauge is not at fault.
Next I attached the ohmmeter to the sensor itself, boiled some water, placed the sensor tip into it and it read 86 ohms, in freshly boiled water! So at boiling the sensor isn't anywhere near to tripping the gauge to even start reading cold! So I tested the old sensor that I was replacing and in boiling water it shows 94 ohms?
What am I doing wrong, is there an assumption I am making here in error? I want to conclude the new sensor is bad, but the old sensor reads nearly the same reading under same conditions.So yes maybe they are BOTH bad but that seems to be pushing probability.
If it matters this sensor is the type that is inline from radiator to heater core, not the type that is in the engine block, at some point ford changed their sensor setup but didn't change the schematic drawing. Which doesn't matter the only difference is the one in-line has a ground wire to it rather then grounding off the engine block.
Vehicle is a 97 Ford Ranger with the 2.0 liter engine.
View 4 Replies
Ford crown vic, 1999, 125k miles, no engine work has been done, did flush cooling system in spring of 2013 and put in a 50/50 mix of coolant and distilled water (from a jug). No problems for the summer of 2013, have been using heater with no problems until around Tuesday of this week.
Car runs fine, no leaks, coolant checks out good. BUT now.. My temperature gauge hardly moves (up) and the heater blows warm air only. If I am driving the gauge will not move, if the car sits running for awhile it will move up some and the heat will get warmer inside of the car. My guess maybe a stuck thermostat?
View 3 Replies
I own a 1997 ford f150 V6 engine and I have problems with the electrics. I turn the key on and the engine starts up runs great but I then look at the gauges and not one moves at all the. No fuel when i have just filled up,no tep,no oil,no battery all read nil. I went a drive and the speedo reads 0 it does not move but the truck drives great. Could it be a fuse, does a fuse control the gauges, which one it could be. I have lifted the hood and under the hood on the drivers side there is a box with small and larger fuses.There is one that is very small and the colour is white that's blown. Would you no what that fuse is for.
View 1 Replies
I rebuilt the engine on my toyota celica. After putting everything back together there are a few bizarre symptoms I am hoping to get sorted out.
1) It only starts with starting fluid, but once it starts it will run continuously without dying.
2) The temperature gauge goes up relatively quickly, and also moves with the throttle. For example if it is as the 1/3 level and I apply throttle it will bump up. It continues to jump along with throttle play.
3) When I remove the coolant sender and/or sensor plugs, the gauge still reads the same (is this normal).
4) The fans don't turn on unless I remove the sender cable (the one with one wire and not two)
If I understand correctly the sensor with one wire is the sender and the sensor with two wires is the temp sensor. I am having a hell of a time determining the difference. The one with a single wire contact is plugged into the thermostate cover/pipe. The one with two wires is in the thermostat housing.
Did I fry the ECU somehow? What is going on?
View 14 Replies
1988 ranger, its a automatic 4x4 v6 and is leaking tranny fluid real bad. Truck barley moves because fluid comes straight out...
View 1 Replies
Just purchased this truck and noticed the gas and temp guages neither work. Where do I start/ How about fuse box?
View 5 Replies
98 ford Ranger 2.5L.
I have not heat from the vents, doesn't get warm at all. If I idle the enginer in 30 Degree weather it gets to almost the C.
Upper Radiator hose is hot, I have verified the thermostat is new and it opens at 192 degrees as it should. Replaced the Water Pump, Fan spins freely.
I have attempted to burp the system, it isn't kicking out anymore air from the lines that I can tell. I used a large funnel and filled it with Anti-freeze, it filled the radiator, burped the system and the reservoir filled to overflowing. All with the engine hot. (To be specific the funnel was always full of fluid so no air could get sucked backwards)
The heater core hose on the left when looking from the front of the vehicle does not get hot, the one on the right gets warm. I theorize that the heater core is clogged up somehow and that is why that left line doesn't get hot. There is no fluid in the cab of the truck from the core.
View 9 Replies
My girlfriend has a 97 Ford ranger that can't make it out of the driveway when it warms up to operating temp. This is what was replaced thus far. Cat, timing belt, plugs and wires, air and fuel filters. It has about 37 psi at the rail, the codes shown were second 02 sensor, and fuel to lean on bank one? I looked thru a few postings but I'm actually at work and can't really spend too much time looking thru much more. The timing was checked about three different times just thinking that was the problem after the new belt was installed. It does idle perfect at all temperatures it just won't go when it warms up. Unplugged the TPS, no change, was thinking electronic ignition module but not sure if it has one or where it is if it does.
View 11 Replies
Gas gauge went from about 1/4 to full in about 3 seconds and hasn't moved since. 2000 B3000 Mazda 3.0 V-6 auto. I've checked all the instrument cluster fuses (11,26,33). I know of the method of disconnecting the connector at the gas tank to see if its the sending unit or the gauge but I can't see or feel in there good enough to do that. Would either one go bad that quickly? Doesn't seem likely to me.
I've read about a "slosh sensor" in a post on this forum - does my truck even have that? I've had an intermittent wiper problem a couple of times but the multifunction switch wouldn't be involved would it? I'm just trying to see if there might be a simple fix before I add it to my repair list when I take it to have the ball joints replaced.
View 9 Replies
2001 3.0 XLT Ranger 2wd 4 door
Okay getting ready to trade in my Truck. So I removed all the extra things I put on there while I was in college, the amp, fog-lights, and analog oil pressure sensor along with their wiring. It was pretty easy minus removing the oil pressure sending unit part.
I had to unplug the MAF to move the intake out of the way while I was repairing a loose vacuum tank. But I forgot to plug it back in when i closed everything up. I started the truck and drive it about a half mile before I was able to pull over and plug it back in. Truck ran and shifted fine after that, but the CEL came on. P0119 Coolant Temp Signal Intermittent. Guy at Autozone said it was Intake Air Temp Sensor intermittent and I could just replace the part, but they were showing a separate part even though it is built into our MAFs.
So now the CEL is on, can get it to go away. Truck is a little jerky every once in a while, like a misfire, when between 50 and 60. Before all this the CEL was off. Now after I cleaned it up and removed some of the superfluous accessories, I get a CEL. I wanted to trade it in this coming weekend without having to take a loss because of the CEL or spend more money to fix it.
View 3 Replies
I need to know what the wire colors are for a engine temperature sensor connector (2-wire) are and the correct wiring diagram to get the temperature gauge to work again
View 1 Replies
My 2001 Ranger V6 with 160.000 miles runs like a Swiss watch. After warming up slightly it idles at the typical 750 RPM. I can pull out of the garage, park in the yard, shift from D or R into P and the idle holds at 750 RPM until I turn the engine off.
But, If I've driven to warm the engine to normal run temp and go through the same D or R and into P, the RPM drops to nearly Zero and sometimes the engine stops.
This has happened in the past so I take out the MAF, squirt it good with MAF cleaner, put it back in and everything is hunky-doory. But not this time. What am I missing??
View 7 Replies
I have a 2011 xlt extended cab with a 2.3l 4 cylinder. The truck is great... I put 120,000 miles on it in under a year.
But about a month ago the temperature gauge started malfunctioning. for what ever reason -- the truck is NOT over heating-- the gauge would increase past the "H" and then the temperature light would come on. Because the truck thinks it's overheating -- the engine goes into a "safe mode" and runs with no power. When i shut the motor off and turn it back on temperature gauge resets and the truck will run fine.
Then in another 50 or 100 miles it will do it again. Why is it doing this? I took it to the dealer here in Columbus, Ohio and the mechanic installed a new thermostat and a new "control modulator" (and a part -- not really sure what it is called) anyway, the truck is doing the same thing and the mechanic still does not know
View 3 Replies
I just picked up a 1984 ford ranger long box 2 wheel drive w/ 2.0 l and carburetor for our daughter whom is just 15. it has a whopping 19,000 actual on it! It was my wife's grandma's farm truck - ordered it new from dear born. Any way, fuel gauge is pegged at empty and they had a new float assy put in about 5 years ago, but it is dead now, it doesn't appear that this sender is avail any longer. What part might fit in there and or what do i have to do to maintain the original gauge in the cluster but have a working sender to talk to it? is there another unit that goes in the tank that i can modify the signal out to read right with the built in gauge? There can't be too many different ones out there is there?
View 8 Replies
I have a 97 Splash with the 3.0, oil pressure goes up to about the middle of the gauge after startup, however, it stays there whatever I do, warm/cold, idle/5500 rpm. Is it supposed to be like that?
View 4 Replies
My oil pressure gauge does not work. I was told that it's most likely the sensor. Where would I find this to change it out?
View 3 Replies
Was fixing leaking water temp sensor today and noticed the nipple under oil fill cap didn't have hose on it. After further investigation I found open spot on air intake hose with nothing in it. Both places seem to have vacuum, what goes here. BTW it is a 1999 Ranger ext cab with 3.0 flex engine and auto trans. Will try to get picture n post also...
View 8 Replies
I have a 2001 ford ranger xlt 2.3L and the temperature gauge has been staying a cold. And my heat doesnt heat well. I'm guessing I need to replace the thermostat. Before I do that could it be anything else?
View 9 Replies
I have a 2002 Ranger V6 3000 with 100K miles. Can I add a higher viscosity oil since my pressure gauge is acting up. I changed the sending switch twice but the gauge still acts up occasionally. I was thinking of adding 10/ 30 on my next oil change. I do live in the area where the air temp is quite high in the summer. The truck runs well except for the oil gauge, in my opinion, is giving false readings.
View 14 Replies
