Ford Ranger / B-Series :: Starts Then Dies After Few Seconds


Jun 8, 2016

I have a 2005 ranger SOHC 4.0 new rebuilt engine It starts then dies after a few seconds then doesn't start at all unless it sets for a few hours or over night and will do same thing. It has 60 psi on fuel rail, good spark I'm starting to think my PCM is causing all this?

View 14 Replies

Advertisement

Ford Ranger / B-Series :: 1992 - Starts To Chug And Sometimes Dies For Sitting At Idle For 30 Or So Seconds

I've got an issue with my 92 2.3 ranger.... sitting at idle for 30 or so seconds it starts to chug and sometimes dies.... I can hit the throttle and its fine for another 30 or so seconds.... while cruising on the freeway after about 30 minutes it starts to cut out badly... let out of throttle for a few seconds and it clears up and drives fine...

Here's the part that has me confused... pulled codes yesterday using a innova scan tool...

koeo were 4, 10, and 538...
koer were 111, 10, 157, 158, 181, 327, 328, and 334....

How does it give me a 111 pass code and then still come up with all the other codes? I am thinking my ecu may be screwed.....

View 4 Replies

Ford Ranger / B-Series :: Engine Starts Very Briefly Then Begins Shuddering Violently And Dies Within A Few Seconds

'02 Ranger XLT, extended cab, 4X4, 4.0L SOHC, 5-speed manual, 114K miles.

Problem has occurred twice. After extended run time and engine fully heated, when I get home and shut it down, then attempt to restart within a short period of time, the engine starts very briefly, then begins shuddering violently and dies within a few seconds. Re-attempts to start result in a very shuddering attempt to run for a couple seconds, and then it dies. After a couple of re-attempts, it doesn't even attempt to start; just cranks over with no results. Has to sit about 7-8 hours before it will restart.

No OBD II codes; Passed, no codes shown. I purchased a crank position sensor, but haven't installed it yet: just a stab in the dark after hearing other people's experiences with other vehicles.

First occurrence followed a lengthy trip in heavy stop-and-go traffic. Shut it down when I got home, then attempted to re-start after a few minutes to run a short errand. Sat for two days without any re-attempts; then restarted and ran fine on first try a couple days later.

Second occurrence followed a couple hours of hitting yard sales with the neighbor, in which time I did not shut the truck down; just left it idling while we perused the sales, for fear it wouldn't re-start. Reckon it's a good thing I did, 'cause when we got home and I shut it down and attempted to leave again shortly thereafter, it malfunctioned as described.

Retries failed after sitting 4-5 hours, but after eleven hours of sitting, it started right up and ran normally.

View 3 Replies

Ford Ranger / B-Series :: 1994 4.0L - Starts / Stumbles And Dies Soon After

Ole girl finally let me down, or I let it down at 224,000mi. Started just fine one early cold morning and in about 30 seconds started stumbling and down for the count she went. Acts like it wants to run but will only stumble.

Checked inertia switch (ok) and all vacuum lines/caps appear to be fine. I was kind of due for new set of plugs/wires and a fuel filter. Replaced all didn't see any problems with the old when pulling. She will run for a few seconds, but stumbles and not smooth while running. Checked fuel pressure KOEO 40psi steady. I can hear fuel pump charge system per as usual.

Seeing as it is super cab checked for chafing on wiring to fuel pump under cab. Looks fine. I've heard tell could be alternator, which seems odd to me. Wondering if it would be worth pulling it off and taking it in for a bench test? Maybe I missed something. I know the intake gasket is suspect.

View 14 Replies

Ford Ranger / B-Series :: 1992 - Starts And Stalls / Won't Run More Than 3 Seconds

The truck started acting up while driving. It would shut off (no miss or anything), but would start again. Now it is sitting in the driveway and wont run more than 3 seconds. The fuel pump has been changed and did not work. The fuel pump relay is new and did not work. I read that the fuel pump goes to another circuit after start up. Could it be running to start and then shutting off? Inertia switch is not tripped. Where to look next. 1992 Ranger 6 cylinder ....

View 10 Replies

Ford Ranger / B-Series :: Truck Almost Dies And Starts Sputtering - Spark Plug Caps Pop Off

My 2003 2.3L used to run bad... it had a lot of lag to it when i would try to accelerate. The check engine light was on so i got it checked, and the reading said o2 sensor high voltage or something like that... anyways, i purchased a new sensor (i researched, and found there is only an upstream o2 sensor), replaced it, and the truck ran WAY better, no more lag during acceleration, it was crisp. As i was driving home one day, i was accelerating up a hill, and at about 4000 RPM, the truck almost dies and starts sputtering.

The check engine light started flashing, so i new it was serious, but luckily i was able to make it back to my house. When i got home, i looked under the hood and noticed that #2 & #3 spark plug caps had popped off the spark plugs. What I don't understand is what would have caused that to happen in the first place.... Is it a clogged Catalytic convertor, or is the o2 sensor bad.... Ive read different opinions and technical diagnostic possibilities, but man, i don't want to throw a bunch of money at a truck that I'm really going to have for a few more months. but I need to get it fixed in the mean time.

View 2 Replies

Ford Ranger / B-Series :: 1992 - Engine Starts And Runs Couple Of Seconds Then Shuts Down

I have a '92 Ranger with a 2.3 liter engine. She starts and runs a couple of seconds and shuts down. I'm thinking maybe a fuel pump is not putting out thepressure needed. Gotta go to work tomorrow and gotta get the truck running today.

View 2 Replies

Golf V R32 :: Car Starts For About 3 Seconds And Then Dies

I've shipped my R32 back to the UK, the combination of cold and damp weather has taken it's toll on my car. I started it up Saturday and left it ticking over to allow it to warm up before driving it. The car is used to Houston heat, so a few minutes running will allow the oil to warm a little as the weather here is around 40F at the moment. The car ran for 5 or so minutes, then stalled.

The car starts to about 3 seconds, then dies. I have checked VAGCOM, the only fault is a steering wheel sensor (?). It has a full belly of Shell 99 RON fuel and was serviced just before if left the USA in October.

I have had it towed to the local dealer for repair. I have tried disconnecting the battery for 30 mins to reset the car, it didn't make any difference. I have also tried another key in case it's s sync problem.

View 10 Replies

Ford F-150 (2004-2008) :: Truck Starts Then Dies A Few Seconds Later And Battery Light Illuminates

This is concerning my little brothers truck. It is a 2008 4.2 liter with around 55,000 miles on it.

He drove it to work today, and called me this afternoon saying that the truck starts then dies a few seconds later, and the battery light illuminates. He and a coworker checked the battery and connections....cleaned off corrosion on terminals, battery reads 12.xx volts without a load on it, it is the original though.

As of right now he is changing the fuel filter which hasn't been done yet. I also know of issues with the fuel pump driver module. I remember checking the one on my 2005 back when I owned it. As I recall it causes a no start condition, but would it cause a start then stop condition like this? He will check this when he is done with the filter.

Anything else that we can check in a parking lot to try and at least get it home?

View 6 Replies

Ford Super Duty (1999-2016) :: Truck Starts Then Bogs Down And Dies After About 30 Seconds

Simple enough the truck starts then after about 30 seconds it bogs down and dies. I am getting these codes.

705 Transmission Range Sensor Out of Position

708 Transmission Range Sensor Circuit High Input

720 Output Speed Sensor Insufficient Input

743 Torque Converter Clutch Circuit

745 Pressure Control Solenoid Malfunction

1747 Electronic Pressure Control Solenoid A- Short Circuit

Sounds to me like the converter it locked up. What do you think? Its a 5.4L

View 3 Replies

Ford Aerostar :: 1994 Starts / Idles About 10 Seconds Then Begins To Idle Rough And Dies

I just replaced the water pump and put it all back together, now it won't run well enough to drive. Checked vacuum system, all sensor connections, hoses, gas cap, changed fuel filter, I can hear the fuel pump kick in, reset system with battery disconnected and have looked at everything I can think of so far.

Now - starts fine, idles about 10 seconds and then begins to idle rough and dies. If I use the throttle I can often keep the idle up, but then backfires or acts like no fuel and again dies. Used fuel cleaner and made sure there was plenty fuel in tank.

I am looking at replacing sensors at this point but which one first?? They get a bit expensive real quick.

View 5 Replies

Tiguan :: Starts Easy But After Few Seconds Dies

So i start my car and it starts easy but after a few seconds it dies. I can get it to keep running by changing the fuel mixture but then it has no throttle and it will die if i try to use the throttle. It is 1985 VW Jetta engine in a 1981 Scirocco

View 2 Replies

Phaeton :: Car Starts Fine But Dies After 10 Seconds

I have an 04 w12 with 80k miles on it. It will start fine but will not run for more than 10 seconds. As it idles down from startup it settles to about 700 RPM's where it normally does then dies. If u drive it it will start and go into gear fine as u go to pull away it loses all power and dies. I have checked the minor things i know like air filters, oil, tranny juice all appears normal. New batteries less than 3 months ago also.

View 11 Replies

Prius (Gen 2) Fuel :: 2006 Starts And Dies After 15 Seconds

2006 ... HV battery changed over 4 months ago and car ran fine until last week when the car just stopped and won't get ready. Before that incident, the vehicle was running fine all day, while he was returning from the days chores in the evening, it just stopped, dashboard all lit up. After a while, the car started again, and he was able to move it away to the side of the road...just about 2 meters and it stopped again.

View 15 Replies

Phaeton :: V8 Starts Fine But Stalls And Dies After 15 Seconds

I am working on my father's boss' 2004 Phaeton V8. The car usually sits on the weekends. What it is doing is, it will start and run smooth, but after 15 seconds, on the dot, it stalls and dies. It sounds like it is starving for fuel.

What I have done so far:

LH intake actuator arm found broken, replaced both with "Gruvenparts"

Checked all fuses and relays

LH fuel pump reads 14 volts until the relay kicks it off

Tested fuel pressure-good

Batteries fully charged

LH fuel pump reads 0.7 ohms w/key off

RH fuel pump reads 6.0 M-ohms when first connected and gradually climbs to 31.5 M-ohms

(I assumed this meant RH pump was bad and so I pulled it out and bench-tested. Ran perfect and tested at 0.7 ohms out of the car)

Re-assembled everything to pull the car out of the shop, and wouldn't you know it started and ran like normal.

Road-tested for 2 hours the next day without any problems.

So, I call the customer to pick it up and he says he will be there 2 days later.

View 15 Replies

Town Car :: Starts And Dies Within 3 To 4 Seconds After Sitting Idle For A Week

Went to start this 5.0 TC after it sat idle for a week, and it died within 3-4 seconds. Further attempts resulted in similar response. After some initial checks, I was able to keep the engine running by manually depressing the IAC plunger into the barrel. The engine ran fine as long as I could hold that, but stall immediately after release. Codes: TPS out of range; HEGO HO2S sensor out of range-always lean. Bought a new TPS no change.

Today: With the key "on" and engine off, the fuel pressure is a steady 38psi. There is an air release button on the fuel gauge line and when I pushed that, the gauge pressure dropped to zero and does not come back (until you key off and on again). I removed the IAC from its mount and with the key on--I observed the plunger move inside its body--guessing maybe 1/4 inch. I casually checked all the engine management items I see in books and looked at vacuum hoses and couldn't see anything amiss (also climbed on top of this engine and checked the rear--PCV lines etc.). I removed the fuel regulator vac line and observed no fuel leakage there.

View 1 Replies

Kia - Rio :: 2005 - Car Starts Roughly - Idles Horribly For A Few Seconds - Dies

It's a 05 Kia Rio. I've recently put a bit of work into it due to a few issues which were fuel related, namely replacing the fuel filter/pump. It also has brand new spark plugs. That solved the issue that originally put it on blocks for a few months and it ran fine for the past few weeks.

Today I went outside to drive to work and got the symptoms in the title. I know it's not a spark issue because it does start, and I used it on accessory to air up my tires this morning.

I'm just not sure where to go next. I've done a bit of searching and have found recommendations for checking the grounds and the distributor cap.

While running at rough idle, depressing the accelerator makes it die faster, rather than keeping it running. It rained last night and this morning. It's about 70 outside instead of the 80-90 it's been the last few weeks. No check engine light, but I've only tried to start it about 10 times.

View 2 Replies

Accent LC (2000-05) :: 2004 - Starts And Idle Fine For A Few Seconds Then Dies - No CEL

A few days ago, I went to start the car, and it will start, and idle fine for a few seconds, and then begin to run crappy, idle down, and die. I tried starting it, and giving it some accelerator pedal, and it dies. I changed the timing belt, idler pulley, and tensioner this summer, so I'm ruling out a bad timing belt. There is no check engine light, and I replaced the plug wires because when I removed the cover, I noticed one of them was worn in a spot, and the wire shielding inside the rubber insulation was visible.

View 11 Replies

Ford Ranger / B-Series :: 1984 - Dies While Turning Right?

I didn't really know where else to turn (no pun intended) every time I turn my wheel to the right the truck sputters out and dies, i checked the ignition switch, tightened her up and shes still killing the engine when i turn right. All other power remains on stereo, car charger etc. its not so bad on continuous turns i can just pop the clutch but for stopping and turning its a huge issue. Why turning left is fine but right kills the engine..wondering if maybe the prongs on the ignition switch may be bad?

View 7 Replies

Ford Ranger / B-Series :: 1985 - Bogs And Dies While Driving

I have a 1985 ranger 2.3l efi and it bogs and dies while while driving, it can sit and idle all day long but when you go to drive it, it works great for 3-4 minutes then out of nowhere starts bogging sometimes I can keep it going a little longer but in the end the truck always dies . I know I'm loosing fuel pressure , I hooked a gauge up to it and drive it down the road when the truck died it showed 10 psi , from here I'm lost . It has a new fuel pump in the tank and I can hear the other one running when I click the key on , Also two new fuel filters .

View 3 Replies

Ford Ranger / B-Series :: 1987 - Engine Dies While Driving

Recently, today in my 87 Ranger suddenly the engine dies and all electronics in the cab fail.

I noticed under the hood that the fusible link connected to the battery and an orange and black wire was smoking. Tracing this line i found that it leads to the ignition switch, as well as some other places.

There is another fusible link and the junction between the yellow ignition wire and the orange and black wire from the battery. This fusible link also was failed.

I'm planning on replacing the fusible links tomorrow but in case that does not fix it, where to look next.

The problem only occurs when the key is in the ON position. I'm thinking maybe I could do some tests with a multimeter on the ignition switch but am not sure of the details of what I should test for.

Summary: Fusible Links C, and E burn out when the ignition is in the ON position.

View 6 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved