Ford Ranger / B-Series :: Speedometer Will Reverse Despite Of Increasing Speed When Gets Over 75 MPH
Apr 3, 2017
1999 (built late 1998) Ranger 2.5 stick 2wd single cab. If I get much over 75 MPH the speedometer will reverse direction despite increasing speed. If I then let off the throttle completely, the speedo will jump right back up and indicate the correct speed. Continued operation without letting off the throttle to let the speedo recover will trip the ABS fault light, probably due to the erratic signal.
Disconnecting RABS module has no effect on symptoms. Speed sensor in the rear axle has been replaced already (by me) and the new unit ohm'd out good. Wiring between GEM and sensor checks out as well, good continuity (< 1 ohm) and no shorts to chassis ground. I wish I had an o'scope to take a look at the waveform, but I don't at the moment. It is on my future tool purchase list.
View 3 Replies
Advertisement
On my '96 ranger with an automatic the reverse lights only come on between park and reverse, but once put into reverse they go out. The gear selector on the dash reads right, when the needle is on"P"it's in park, "R" drops into reverse and so forth. Do I need to adjust the shifter cable on the side of the transmission? If so how do I do this (I kinda need step by step with removal and adjusting, I've already tried and couldn't get it off the bracket). It's starting to drive me nuts, I've searched on the web for hours with no luck. I've even posted on other sites with zero answers.
View 7 Replies
I have the infamous ABS light & speedo not working on my 2000 Ranger. I replaced the ABS Speed sensor on the rear diff as has been suggested on many posts, but it didn't solve the problem. Did I get a bad part or is there something else I should go after?
View 7 Replies
so heres whats happening. My 98 ranger speedometer has not been working since I owned it (I am the second owner who got it from a grandpa) and I've replaced the vss sensor two times, got a new connector and gave that a try and still nothing. Yes I've looked for cracks in the wire or any exposed copper, I've looked through many forums and cant figure it out. At first before replacing the vss, my abs and check engine light weren't lit up until i put a new vss sensor on that i got from o'reillys, so then i got another one thinking it was just a bad sensor and still no luck. another thing is when its cold in the morning and i get in my pickup to go to work it will start working once i go over 30 and fluctuate between that and 20 but if i don't accelerate it will not bounce all over the place.
View 4 Replies
I have a 2000 ford ranger 4.0L v6. My problem is the abs light stays on and the speedometer won't work till i hit about 35-40mph.
View 14 Replies
Last night the speedometer started acting up, would fluctuate when the truck went over bumps and completely cut out on moderate right turns. Looked underneath as well as one can in the dark and couldn't find anything loose.
This morning I searched on here and the VSS came up numerous times as a common failure. $15 and about a half hour later I had it installed, and while I was under there I took a better look at the other connectors to double check harness connections for tightness and cleanliness. It all looked good, so I went ignition on... and the light came back. Tried clearing it by keeping the diag connector unplugged while switching ignition off, but no go. Took it for a quick spin around the parking lot, and the speedo was completely dead.
Hit up my factory ETM, found all the relevant connectors and set up a wiggle test of the VSS circuit with the DVOM on audible continuity check. Found one of the wires had chafed against the body right by the under-cab harness connector and worn almost completely through. Cut out the bad bit, soldered and heat-shrunk a patch in, and took it for a spin. Voila! No more ABS light and a working speedometer.
Also fixed the fuel gauge sending unit wire which was in the same connector grouping and chafed (but not yet broken) in a similar manner.
View 3 Replies
I have '90 Ford Ranger 2wd standard cab long bed. A few days ago the speedo stopped working. What is the more likely cause? The gauge itself or a relay/cable. And if it is the cable/relay are they hard to remove & replace.
View 1 Replies
Sold my mazda and got a nice 2000 2wd Ranger XLT with a 3.0L. Today the wife I and took it to town, 10 miles on the highway there, a couple in town and 10 back, didn't notice anything unusual. However I haven't this truck long so I'm not sure what is usual.
Parked it for a few hours and when went out to change the front turn signals to LED I noticed the ABS light was on when I drove it into the garage...
I checked fluid, connections and fuses, no change.I go ahead and swapped the bulbs while letting things simmer, I've had so many of these Fords sometimes the easy fix comes to me.
I backed it out and took it down the road, right away I noticed my speedometer wasn't working, so I let off the gas, when I re-applied the pedal I got nothing, like it was in neutral.
I downshifted to second and got her down and turned around as the O/D started flashing... (so glad because I would have hated walking back), then pulled her back in the garage to check transmission fluid and recheck fuses, including the ones I forgot earlier under the hood. I added a 1/4 qt of fluid then tried a road test again, this time there was a real long pause before it upshifted hard and the CEL came on.
I pulled the codes with my scangauge and got:
P0500
P2120
P0028
And decided I better look some things up and consult the gurus here before I do anymore damage tonight. I'm guessing that I'm looking at a tranny replacement possibly, but with the ABS light and speedometer failure I'm not 100% sure what is going on here...
View 12 Replies
1998 Ranger... I started having Speedometer/odometer problems after a power surge when my alternator went out. I knew the alternator was going bad and I tried to limp home another 5 miles rather than pay a tow bill and the alternator overcharged for a few seconds before completely dying. Since that time the only problem I am left with is my Speedometer and odometer have not worked. Scan tool says p0500 and I have replaced the ABS sensor on the differential with an OEM part but still no speedo or odo. I have checked all the fuses and relays associated multiple times. I do suspect that the RABS resistor is bad but there is no ABS light and it doesn't make sense that this one resisitor is the sle key for the whole speed control circuit. It's a manual transmission and RABS only. I swapped out the Cruise Control Servo with no luck as well. I am running out of options before having to take it to a dealer because I have to pass inspection. I have also checked and there is no power coming to 679 (GY/BK) into the instrument panel. I have also checked continuity for the rear harness to the ABS sensor and it is good.
View 2 Replies
so i changed the speedo cable and speed sensor in my 93 ranger, but still getting the speedometer bounce. what could be next? the speedo housing in the cluster? lubed the inner cable, made sure nothing is kinked or sharp bends. Put in a new vehicle speed sensor while i was at it just bcuz. cruise control does not hold a steady speed either but i think the 2 are not related. I'm leaning towards the cruise control servo as to why it does not hold a steady speed. Most of the time once i get to around sixty i'm basically driving by ear bcuz the speedo bounces from 60down to 55 and back up.
View 3 Replies
On my '91 last week I was driving on the highway about 60-65 when all of a sudden the speedo dial started climbing to 70-75-80-85 and past. The odometer seems to be working ok? Still when I drive it still operates in the same manner. It never bounces around or falls back. The needle is sort of stable such if I maintain a speed the speedo will maintain even though it's incorrect. There is a slight wavering of the needle meaning it's not as stable as it use to be. With the odometer working I was wondering and don't know. Does the cable drive the needle or is it electrically controlled? I'm thinking of grabbing another instrument cluster it that is the problem, I'd like to know more about it and understand how it works so I don't just throw parts at it until it's fixed.
View 1 Replies
I lost the windshield wipers, speedometer, dome light, door alarm. Check all the fuses I can find all are ok. Whats wrong.
View 7 Replies
I have a 1994 Ford Ranger XLT xcab with a 4.0 engine.It will take off and drive in the freezing cold but when it warms up it will only go in reverse.Once in awhile it will go into drive.What seems to be the problem. I had also backed up over a railroad tie in an icy parking lot but still drove away.
View 3 Replies
I'm having trouble with my auto tranny again. it is a 4r44e and is in a 1999 3.0 flex 2wd extended cab. It will not pull in reverse, seems to be slipping bad, and it won't pull in forward gears unless you switch OD off. Then it seems to pull fine but still not in reverse. I haven't drove it very much to see on changing gears and such for fear of burning it up.
Fluid is still like new no codes showing just started out of the blue while my son was driving. All electrical is hooked up tight and no leaks fluid is little overfull but not much. I am going outside now to adjust intermediate band to spec. had trouble with overdrive that had everybody stumped if you remember and it was overdrive band adjustment so going that route first.
View 6 Replies
2000 ranger v6 automatic trans electronic 4wd shift on the dash. Plowing snow all of the sudden lost both forward and reverse never slipped or made any noise. Transmission fluid is fine to the level and clean. Put in drive nothing and reverse nothing put it back in park you can hear the park paul trying to click in. Towed it back to the shop thinking maybe the transfer case was junk. Decided to check the actuator on the transfer case no power going to it, go back to the switch no power there either check the fuses both are good and have power. The question i have is could a bad GEM module cause all this? ps the windshield wipers do work.
View 6 Replies
Since last summer my truck keeps blowing fuse 26 and then I have no reverse lights. If I replace the fust its ok for a bit but blows again the same day sometime. The book says its the fuse for revers and overdrive. The overdrive button on the tree shifter stops working too but the truck does not seem to be revving any higher so I think the overdrive itself is fine. I can't find the short but its got to be shorting somewhere...
View 14 Replies
Why my trucks engine is cutting out. idles fine and runs fine when on the road, it only stalls in park if i rev the engine, and it stalls immediately when i put it in reverse.
I took it to a shop and they scanned it and said it was a o2 sensor problem. replaced both o2 sensors(they were both bad) but no luck there, still having issues.
View 2 Replies
I've got a 2008 Ranger FX4, 4.0L with manual transmission. Recently I noticed that I have no reverse lights. I have to parallel park on busy streets from time to time, so this is a safety issue that I need to fix.
I checked the bulbs, both seem fine - would be unlikely that both bulbs would die simultaneously. I checked the fuse. Again unlikely unless the reverse lights were on their own independent circuit. 10A fuse looks fine too.
Last thing I can think of is a switch. I checked my Haynes Manual, there is no mention of it, which is odd, usually my manual is quite good. Where the switch is located? Any experience with swapping this out?
View 2 Replies
Had a long trip with the X this week and noticed a weird vibration up at speed. Anything before 65 mph and the truck was smooth, higher than that a medium vibration developed. Its frequency increased with speed. Never got the truck over 70, but the vibration was there enough to rattle change in the cup holder and the rear view mirror. What it might be? I was thinking a hub bearing... 2000 Limited 4x4 PSD ....
View 14 Replies
Not only will it not go into gear, truck will not start unless clutch is to the floor, and in neutral (it's only possible place) if you pick the pedal up 1/4 inch off the floor the odometer starts spinning around 1 mile in 5 seconds.... if you lift it any more it kills the engine like you shut it off with the key.... odometer reads 99,004 miles now (the last 2 are mine) I bought this truck like this ....
View 3 Replies
Daughter driving truck truck quits moving, I get there no drive and no reverse, has low and 2nd manually.
drive truck home, flush trans and cooler, road test all ok. this was 3 weeks ago.
This morning did it to here again, no drive and no reverse, she drove it home using manual low and 2nd.
I get in and when put into drive it feels like it tries but doesn't go all in, same with reverse. pulled it into low and vola I now have drive and reverse again
I'm thinking a we may have a bad or going bad shift solenoid. What I need to know is, is any of the solenoid valves on when in reverse are they the same as when in drive?
View 3 Replies
