Ford Ranger / B-Series :: Soft Clutch / Gears Grind When Shifted Especially 1st And 2nd
Dec 8, 2012
I have a 96 2.3L 5 speed Ranger. The clutch has been getting softer and softer until about two weeks ago when I couldn't drive it anymore because gears would grind like crazy when I shifted, especially 1st and 2nd. I had no time and just drove my other truck but now I've had a bit of time to look into it. I went to bleed the clutch and then realized there was no fluid in there. So I tried to put fluid in but nothing happened. The clutch is still extremely soft. The truck won't even start when I have it in gear, it turns over and kind of lurches forward, even with the clutch pushed all the way in. It starts right up in neutral. So my guess is I have to do what I really don't want to... replace the clutch!!
Is it possible that since I just put more fluid in the clutch it may take awhile for that fluid to get into the cylinder and I have to bleed it again?
View 6 Replies
Advertisement
148,000 miles, and yesterday my R decided it would no longer allow me to use first gear. It sort of starts to go in gear, but feels kind of mushy, not positive, and if I let out the clutch, the gears grind, but will not engage. All other gears feel and perform normally.
View 7 Replies
Ok at waterfest I got a UM ECU/DSG tune with the spark cut option. I now noticed that once in a while, only in regular D mode, there will be a very very aggressive and uncomfortable shift. It only really seems to happen under higher load and form 3rd to 4th or 4th to 5th. The car shifts and there is like a double spark cut pop instantaneously after each other. It feels like the car shifted 2 gears and each with a spark cut. I called UM and they said sometimes it can be fixed with a clutch alignment. Car hs 56k mile on it and it was just recently DSG serviced.
View 3 Replies
I have a 2001 Ford Ranger XLT 2.3L RWD AUTO.
I've never had this problem but now I can hear what appears to be a electrical noise or grind/whine. This just started happening on Monday. Prior to that I've never heard nor seen my speedometer bounce like this.
I've read that it's the rear diff ABS sensor possibly going bad. So I should have a new one tomorrow via amazon. I have also read that it's possibly the battery? I know the previous owner said he replaced the battery but this was at LEAST 2 years ago. So I know there is a solid 24 months on the battery now, since I've owned the truck...
I've also read that it might be the speedo? These actually go bad? Makes me wonder because of the noise you can hear towards the end like a whine noise. I have noticed that the battery gauge looks a little lower than before... normally it would be at around the MIDDLE of the battery icon and as you can see in the pic it's not now... however, the truck starts up perfectly fine, no hesitation at all or trouble, or having to do it multiple times.. so that makes me wonder is it really the battery?
I have projector HIDS and LEDS inside and have had them for at least a year now, I've noticed today pulling in the garage that the right hid was not flickering on and off persay but the beam wasn't steady like it was.. it was kinda dimming a little along with the interior cabin LEDS.... Battery? Alternator? I'm truely at a loss.
I've also heard there are sensors on the transmission that dictate the speed to the speedometer, problem is I don't know which ones to get.. I don't mind replacing all of them as long as this STOPS.
I did change my rotors and pads, and calipers. This was friday and this didn't happen. I will note that my ABS light is not on nor is it flickering so it makes me wonder as well if that sensor in the rear is bad? I didn't see any bare wires everything is taped and loomed, so I don't think anyone cut the wires back there that I could see at all...
Attached the picture of the battery gauge. And link to the video that I took with my phone...
Ford ranger gauge bounce - YouTube .....
View 14 Replies
So went today and bought a 1993 ranger 4x4 ext cab 4.0! Runs good some bad handy work that i need to fix but truck has plenty of power and good handling...
issue 1- 4x4 not engaging. the light by the push buttons does not come on and you dont hear the "clicking" of the relay trying to engage. so whats the problem and how do i fix it?
issue 2- when clutch is fully depressed and you go to shift (this is only sometimes) you can feel and hear it grind just for a quick sec. and forget about down shifting you cant do that without slowing down. so maybe new clutch?
issue 3- at 65 the vehicle does shake a little otherwise but pretty smooth. any tips on how to smooth it out? maybe new ball joints? tighten some stuff up maybe?
View 14 Replies
Last night, on my way home, I suffered a catastrophic transmission failure in my 1991 2.3L 5 speed. Stepped on the clutch on an exit ramp from the freeway and was rewarded by a LOUD screech/grind, a stopped vehicle, and a transmission "locked" in 5th gear. The local HERO service pushed me out of traffic and I got towed home. Looks like a transmission transplant is in my immediate future. So - the question is, what year manual transmissions match up to a 1991 2.3L 4 cylinder, standard cab, 2WD? I need to start searching salvage yards.
View 3 Replies
I have a 2003 Ford Ranger, 5 speed, with 180k miles. Sometimes, not all the time, when I press the clutch and shift gears, the engine will rev.I dont drive the truck a whole lot, its a 2nd vehicle.
View 1 Replies
I have a 5-speed transmission pickup (’04 Ford Ranger EDGE SuperCab). Clutch pedal feels "normal", No resistance when shifting gears. Will go into gear with ease, except for 2nd gear (grinding noise), must push clutch to the floor and still grinds; but only 2nd gear. In 1st gear, my truck will slowly creep forward as if unable to engage and not having any kind of pulling power. Even when shifting to 2nd, 3rd, 4th and 5th gears, it barely maxes out at 30MPH (top speed unless vehicle is on a slope or slight decline then I can get up to and over 40MPH. Checked brake fluid level, it’s ok. The fluid’s at max. Clutch is relatively new (April 2014), with only about 13,000 miles on it, if that. It must be cylinder issue. Is there any way to tell whether it's the clutch master cylinder or slave cylinder?
View 5 Replies
1996 Ranger 2.3. I bought it from a friend 2 months ago. 228,866 miles. The motor seems to stumble as I'm going through the gears. I've cleaned the mass air flow sensor and installed new air filter. Check engine light has always been on, O'Reillys hooked up their computer to it and said Emission Valve Malfunction. I see the charcoal canister, then I have 2 electrical sensors on same line. First one from canister looks like what Rockauto.com shows as a Vapor Canister Purge Valve. The photo has it with a yellow orangeish top. I don't know what this 2nd sensor is. It has a blue top.
View 2 Replies
I have a 2002 ford ranger edge. swb, 3.0L, 5spd. I have been noticing it is getting harder to shift gears, put in 1st at a stop light lately. There is no grinding just seems harder to engage. Checked fluid level and it is clean and full. Recently i have developed a vibration under power. Let off the gas and smooth as can be, apply throttle and starts vibrating. Not sure if flywheel is "hot spotted" or perhaps broke a spring on pressure disk. Just seems odd it's only under throttle. Yes already checked rear end and U-joints.
View 2 Replies
I've been having problems with my column shifter ever since I installed a Pioneer shift cable probably about 3 years now. I was told and also thought that the cable would loosen up after awhile but it never has. I had some put it on and I watched him do it. He seemed to have some trouble because it took him a long time under the dash. It shifts so stiff that over a period of about 2 years it finally broke the end of the shift tube one night. Luckily I was able to fix it the next day by getting a spare without missing any down time. It was still just as stiff with the other shift tube. It finally broke the plastic on my shifter tonight, not necessarily whatever is causing it but because it takes so much effort to shift into Park, Reverse or Drive.
I think the plastic may have cracked over time. Luckily I had another one at home along with another shift tube. I didn't replace the shift tube this time but I did remove the caps and smear some grease on the bushings to see if it would make it turn. I looked further down at the end cap that broke last time and sure enough one of the bolts was backed almost all the way out. I retightened it tonight too. That's what happened when the bottom broke last time. One of those bolts backed out and it cracked the housing. It works now but if you go all the way to 1st to get back to anywhere it really takes a tremendous amount of effort to get it to shift. Something is not right and I cannot pinpoint it. I know they offer brand new shift tubes but I'm not sure if that's the problem.
View 2 Replies
I just finished replacing the Valve body gasket in my 99 ranger with the 4.0 liter v6 with the 5r55e trans. My problem now is that I have no gears i can shift it but the gears do not engage.. I did install the updated bonded separator plate and the tsb for the blow off valve with it.
View 6 Replies
1997 2.3 5 Speed. My poor truck is having a hard time shifting into gears. I have bled the master off the truck with the correct method, bled it on the truck with the hose on the slave method while pushing the pedal and multiple times with no bubbles coming out at all, no leaks, etc.
Here's the breakdown -
- Clutch, slave cylinder and shifter bushings replaced about 3 years ago (everything has less than 7000 miles on it)
- While driving and pushing in the clutch, it clearly disengages, although quite a ways down.
- Only shifts hard while running. If I sit with it off with the clutch in, I can shift through all the gears with no effort whatsoever. At times while driving, it gets so hard to shift that it may become dangerous.
- Only things I haven't replaced are the master cylinder and the flywheel.
Should I just assume a bad master and just replace it? It's the original with 188,200 miles on it.
Forgot to mention there are times that when I am at a standstill trying to go into reverse, it grinds like the transmission is still engaged.
View 4 Replies
1999 ranger, 2.55 speed. truck idles with very high rpm's when driving and shifting gears. have changed the AIC, mass air sensor. Throttle position sensor and still does it. the AIC has been changed 5-6 times in 6-8 months as parts store kept telling me it was that. What can i look at, check, etc...
View 6 Replies
This morning, I shifted into neutral and left the truck running. When I got in it put it in reverse, the shifter peddle went all the way to the floor and the clutch did not engage. I turned off the engine, and the transmission shifted easily. I put it into reverse, started the engine, and when I tried to shift back into first, the same thing happened. Pedal to the floor with no resistance, and I could not get it into gear. I finally forced it into 1st to get back into the driveway, but had to stall the engine to keep from going through the garage door. The clutch would not disengage at any time. I checked the master cylinder and it is 1/2 full. Has my clutch gone out?
View 14 Replies
When I got home today I went to back into my parking spot and couldn't get my truck in reverse, or any other gear for that matter.
I've been suspecting something was going to go wrong because the last few weeks or so when I push the clutch in it sounded like bb's rolling around in a metal coffee can. Since I have owned it (2 yrs) the clutch has seemed funny anyhow, as in I really have to feather it so it doesn't grab and stall out.
So I've visually inspected what I can so far. Master cylinder fluid is at a proper level and I pulled the inspection cover on the transmission. I didn't see any fluid and reached inside and there wasn't residue in there either. I observed the throwout bearing pushing the clutch cover fingers in when the pedal is pressed and that is about it.
Just wondering about some additional checks I can perform to pinpoint the problem, as well as how to fix it and get rolling again.
1999 Ford Ranger 4x4 XLT
3.0 V6
134,xxx miles
No modifications
View 6 Replies
2003 Ford Ranger .. ac:system is over pressurize when I add freon the clutch goes on and off.Is there a high pressure switch for something
View 1 Replies
My clutch is weak and slips sometimes and I need to replace it. ,I have replaced the clutch disc in other trucks but never a Ranger.
1999 3.0, 5 speed stick, Extended cab....
View 11 Replies
I think the time is near for a new clutch in my 98 Ranger, 2wd/ 5 spd. How tough of a job is this? I've changed the one in my 66 Mustang years ago but things were less complicated then.
View 3 Replies
1997 Ford Ranger w/manual 5 speed tranny
A few weeks back my clutch pedal seemed a bit softer than usual one day. Still it worked fine... no problems shifting. Today after a short ride it went almost to the floor before disengaging. Now I cannot get it in gear without grinding.
So cold out I'm not sure I want to tackle this right now, what to look for and where?
View 14 Replies
I've had my truck a few years now but for 2 it was basically parked. When I started trying to use it again I am having issues with the clutch now. When it is cold everything is fine, but on hot days or after I have been driving for a while It will lock the pedal up and will not let me dis-engage the clutch at all. Sometimes when it does eventually let the pedal down it will go to the floor and stay there for a few seconds until it slaps back up and engages slamming the truck into gear.
I have yet to try much. I'm not good at working on anything other than stereos in cars but I am willing to try. My thought is some water got into the system and is boiling in the lines but I am not sure. Places to start? I really need my truck going and the couple places I've taken it dont even want to try it seems like.
View 2 Replies
