Ford Ranger / B-Series :: Random Miss At Full Throttle
Nov 25, 2014
2002 Ranger XLT 4WD 4.0.. I was passing another car at about 55 when they also started speeding up (go figure) so I floored it and got on around them but before I lifted I felt it miss, the CEL began flashing so I slowed to the speed limit and went on to work. The light flashed for about a mile then went out. So on the way home I floored it again close to home and the CEL came on again. Got home and put the code reader on it and all it had was a random misfire so I have cleared it. The truck has new plugs, wires, etc for a complete tune-up. I don't usually run at full throttle so don't know if that would be normal for the Ranger, the Ranger was my wife's truck for 12 years and now is my DD. Need to clear this up? Thought of changing the fuel filter in that is still the original one.
View 8 Replies
Advertisement
I have a 2000 3.0l ranger. I have been battling an ignition problem. every time the engine is cold it runs terrible like only 3 or 4 cylinders running terrible. if u put a timing light on the wires the pulse comes and goes on random wires. and when it quits that it has a random sputter at idle and misses around 4k when u get into the throttle ...
I have replaced plugs twice and the coil with motorcraft parts and the wires are new autolites. I have also replaced the thermostat and fan clutch it was getting hot in the middle of this other issue ...
Every time I replace something it runs great for a few days then back to running terrible again. am I missing something else do I need to look at a computer or map or tps sensors, or something like that ...
View 5 Replies
My 1995 ranger was running just fine then today overheats in five minutes and then runs at very high rpms, has 2yr old water pump new tstat don't think head is blown no water in oil no white smoke no water on the oil cap, I haven't check the plugs for water, stated raining no garage, when engine is cold starts runs fine,but when it gets hot its like a train...
View 5 Replies
So among the other annoyances my 92 Ranger 4.0 auto has it has a hesitation before it starts spinning the tires under full throttle from a dead stop. It's the 4.0 automatic. I thought it would have more power than it actually does being use to a 2.5 auto. But this 92 4.0 runs and drives good. I've gotten it tuned up with new motorcraft wires, plugs, new coil, fuel filter, fuel pump assembly, fuel pressure regulator, air filter, idle air valve, new O2 sensor, new Dynomax muffler. I can't find any vacuum leaks. The engine idles slightly rough after you start it up from it sitting for a few hours, but quickly smooths out as soon as you start driving it.
This one here has no EGR. Transmission feels good, may have even been replaced by previous owner before we got it. It shifts good and the fluid is clean and the transmission is the cleanest part under the whole truck. No way of knowing for sure. The truck currently has 111,000 miles and I did all that stuff when we got it at 101,000 miles. So what could it be? I'm thinking a lazy injector or could it be the catalytic converter? Or could it be the throttle body? I know I once had a BBK throttle body on it and it made the world of difference in off the line power but it kept throwing too rich/lean condition and a TPS code so I had to return it. It sucks because it did wake up the motor. I returned it and since then the Check Engine Light hasn't come back on.
View 1 Replies
My 99 ranger has a strange issue its got a miss when the A/C is on, when going down the road I can feel the engine sorta pulse for a second, gets better the more I drive it, its got all new plugs and wires, not sure where else to look?
View 1 Replies
I have a 98 4x4 with 145k miles and 4.0 OHV. Symptoms are as follows;
Uses ALOT of oil. 1 quart per 230 miles. Burning bad in rear cylinders, some in middle cylinders, none in front cylinders. Screams intake or PCV issues to me, not rings or valves. Never any smoke, not even on startup. No significant leaks. MPG always 18-20mpg.
Slightly rough idle.
Miss under load below 2k rpm. Not a terrible miss, but you can feel it. Has never lit the CEL. I know the CEL is good.
Never loses coolant. No coolant in oil or vice versa. Haven't done compression test, but doesn't seem like they ever tell you much anyway.
This weekend I replaced all intake gaskets, plug wires, cleaned oil residue off and regapped plugs (they are 3 months old), injector orings, and PCV valve. Flushed and burped radiator.
It's too soon to tell on the oil consumption, but I thought the intake gaskets would have cured the rough idle and misfire. The idle IS much better, but still not perfect. But the low rpm load miss is actually worse now. Still no CEL. Could it be storing codes without lighting the CEL? Also, how do you clear codes on these, can you just disconnect battery, or do you have to clear them with a scanner?
View 14 Replies
Just hoping that there is something common that causes this problem. This thing can idle just as smooth as you could want one to and the next time it will have a dead miss, and the miss is not consistent. It may miss like three hits then be ok a little then miss a little. There is no CE light or codes. Again just hoping there is something common.
View 2 Replies
I have a 1987 ranger 2.9 V6. Have a intermittent miss @ idle when warmed up. What is the proper way to pull the codes from the computer, i,st something about counting flashes or lights...
View 6 Replies
1993 3.0 V6 5 Spd ... Changed plugs wires Cap and rotor put in a new idle control Valve. No Check engine light. When i am running down the road feels like it surges,hickups, while its at idle the motor shakes like no tomorrow. Just dont want to throw money at something and not be the part that was wrong. Truck has plenty of pickup runs like a raped ape going down the highway. seems when i accelerate the miss clears up and not there. RPM gauge needle has some movement in it. Also put in K&N filter fuel filter as well.
View 6 Replies
I have at 2007, 3 liter ranger. I just replaced the plug wires and coil pack. Ive checked and rechecked the wires, firing order is right,everything has spark but i now have a miss from a stop to 1500 rpm. what do i need to do to fix the issue.
View 4 Replies
1999 Ranger 4.0. I have an issue with my ranger. Sometimes the truck runs awesome.While driving along the truck will miss and sputter and buck, when this happens, I almost can't maintain my speed. Sometimes when this happens if I put the truck in neutral and shut it off and restart it. The problem will temporarily go away. Occasionally it will go away on its own. When it goes away on its own it's like someone flipped a switch and all power is returned and running smooth. When the truck is at idle it depends on the mood of the truck, sometimes it's fine and other times it wants to die. I got to make this truck last awhile longer.
View 7 Replies
Its a 1994 with 4.0, automatic, 4x4. Running fine, parked it, a week later I'm getting a bad but sporadic miss that according to the stealership is the 3 cylinders on the right bank dropping in and out. Driving down the road you can feel them drop out and when they come back its a kick in the pants like a turbo kicked in.
Shop says wires are good, plugs are good, and then lost me when they started talking around in circles and not making much sense.
What could make 3 cylinders all on the same side of the engine drop in and out? This wasn't anything that slowly came on. Fine one day, crap the next. The only thing I did prior to was replace the IAC because it was idling high, it was cruddy inside, and it looked like it was original. It was running fine after that till this issue popped up out of nowhere.
Mileage was claimed to be 178k but I'm beginning to suspect it's probably 278k.
View 7 Replies
I have a really nice 1986 Ranger XLT with a 2.9 V6 (injected) and OD Automatic with about 135k miles. I've had the truck for over ten years and have been pretty happy with it. I'm still trying to correct a couple of nuisance items:
1. Sometimes it runs smoothly, and at others it has a rough idle, and once in a while it will even stall. Before it stalls, it idles or runs roughly, and will miss erratically. When it quits, it does not fade out like it is running low on gas; it quits suddenly, like the ignition is turned off. If I am driving at highway speeds, sometimes it will buck as it misses, and sometimes stalls out. But it always starts up right away afterwards. This does not happen often, but when it does, it happens several times over hours or days, and then goes away by itself for months, even years, and then comes back for another round.
I was hoping whatever was wrong would totally fail, but it has been several years and is not getting better, nor worse. Fuel mileage varies, too, from 16 to high 20's MPG. I have new low- and high-pressure fuel pumps (dual tanks), new gas and air filters, checked all the electrical connections, put in a new ignition switch, new O2 sensor, Air Flow sensor, EGR, replaced all the vacuum lines, new battery and cables, new starter, all new electrical relays, fuel pressure regulators, new fuel pump inertia switch, tuned up engine (incl. wires, cap, rotor, ign module, plugs and timing), and cleaned out the already sparkling-clean tanks.
2. My oil pressure will drop at idle to low-normal when the engine is warm. It never goes to below Normal on the gauge. I have replaced the gauge, sending unit, and oil pump. This is a long-term issue, and is not getting any better or worse.
View 2 Replies
I have a 85 bronco 2, but i have no luck with responses in Bronco 2 forum, so here goes. It is the 2.8 carb, manual trans with 109K miles. Idles really well some hesitation when taking off but really bad miss and not power under acceleration. KOEO codes are 31 and 84 CM code 18. I have plugged the vacuum line to the EGR and have noticed a dramatic difference. I have tried to rev the engine and check the vac line to the EGR but I do not feel any vacuum, and at idle the vac line on or off doesn't change things. Any recommendations to whether it is the Sensor or the valve itself and what gives with the 18 code. I am hoping to have timing checked by the weekend.
View 2 Replies
Gas gauge went from about 1/4 to full in about 3 seconds and hasn't moved since. 2000 B3000 Mazda 3.0 V-6 auto. I've checked all the instrument cluster fuses (11,26,33). I know of the method of disconnecting the connector at the gas tank to see if its the sending unit or the gauge but I can't see or feel in there good enough to do that. Would either one go bad that quickly? Doesn't seem likely to me.
I've read about a "slosh sensor" in a post on this forum - does my truck even have that? I've had an intermittent wiper problem a couple of times but the multifunction switch wouldn't be involved would it? I'm just trying to see if there might be a simple fix before I add it to my repair list when I take it to have the ball joints replaced.
View 9 Replies
This has happened before on my 98 ranger 2.5. You can drive it 10,000 miles without any issue and then all of a sudden you take off and there's no power but it quickly returns. Within the last year I've changed fuel pump assembly, fuel filter, injectors, cool packs, and plugs. Is it mass air flow? It seemed to happen a lot more after I cleaned it. My scan tool is amateur but it has a maf reading in lbs. What should it be while driving? Fuel pressure is always between 65-72 when I check it within specs according to my book.
View 10 Replies
I have a weird issue. When I'm running AC on my 2.3l ranger sometimes the idle wont go down but rather hold its current RPMs till i either turn the AC off or place the truck back in gear. What that could be?
View 6 Replies
I have a 2003 ford ranger edge with the 3.0l engine. It started acting up today so i brought it to get checked because the check engine light came on. Three codes where pulled p0300, p0306, and p0313. They were multiple/random cylinders misfiring, cylinder 6 misfire, and first misfire at 1000 rpm. I have replaced the plugs and coil and still have the trouble.
View 5 Replies
My fuel gauge is stuck at the full mark. What to check and where to start?
View 7 Replies
97 ranger 2.3l ... I have a problem where I'm losing full power (like cutting out) while under acceleration it's only for a split second almost like a hesitation. I got p1443 for the first time today and I was looking at my fuel trims and I noticed my long term FT is at 99.2% and never changes while my short term goes between negative and positive no more than 6%positive and like -4% I assume this is normal for short term but I really am just guessing on that. I am thinking perhaps I need a new fuel pump...but maybe I'm wrong...truck has a new fuel filter and a new evap purge solenoid...
View 14 Replies
1986 Ranger 2.3 inline 4
I just recently bought an 86 Ranger from a friend. It had recently stopped working and had no desire to fix it. So here I am. The truck will sit in park and rev all day long, once its in drive it idols fine and moves its self down the street. The problem occurs when I apply throttle. It begins to bog down and I cannot get past 20mph. I have replaced the fuel regulator and also I took the tank down and replaced the fuel pump. The fuel filter is two months old, and the throttle response sensor is two weeks old.
View 2 Replies
