Ford Ranger / B-Series :: Power Steering Leak / Sensor On High Pressure Line?
Dec 8, 2010
I think I've tracked my power steering leak to some type of sensor on the pressure line, close to where it connects to the steering box:
I assume this is a pressure sensor? I got no CEL or anything like that when the fluid had leaked down to the level that the pump started whining pretty badly though. As far as I can tell by looking at pictures, the parts store replacement pressure lines do not have this sensor, or any provision to connect a sensor to it: Advance Auto Parts: Power Steering Pressure Hose by Powercraft - Part 71878
I may just put a replacement line on there and leave the sensor plug hanging and see what happens...
View 11 Replies
Advertisement
I have an 03 Accent. The all metal high pressure power steering line had a leak. So I bought a new one for around 70 dollars from Hyundai. This part has a curved shape and fits around the radiator. The old one was difficult to get off, but the new one is proving impossible to get on. I cant get it into place.
View 2 Replies
I have a 2009 Ranger 2.3 L manual with about 100000 miles. The engine was bogging down and I just found out that the MAF sensor is bad from testing it. In the process, I measured my fuel pressure to be 73 psi (manual says 60-65 psi). So I have two questions:
a.) Is there any chance of just cleaning the MAF sensor. The sensor has zero volts when running and warm (or .02 v) and barely changes when reving the throttle.
b.) Perhaps then the high fuel pressure is an unrelated issue. Is this so high that I must change the regulator as I have to change the pump as well? Might it be some other issue than the regulator which is what the Hayness manual says?
One theory I had for the high fuel pressure is that the bad MAF was leading to bogging and lean conditions and the computer was running the pump more to compensate but I think the computer might run the pump based on fuel pressure not the o2 sensor.
View 7 Replies
I just replaced my 3rd HP power steering line last night( 3rd in 300K, always blows the same point....fitting comes apart where it attaches to the pump.
I'll start, mine have gone about 100K plus or minus 10K, almost thinking about making it a 100K maintenance item.
View 14 Replies
I've been watching fluid build up on what I think is the hi-pressure line on the hydroboost. It appears to be originating at the coupling in the line because it is dry back at the unit.
Is there an o-ring or nylon washer in this fitting?
Can it be tightened?
Does the o-ring or washer need to be replaced?
Is it a sign of something else, like a build up of pressure in the line that is too high?
I currently have zero problems or noise coming from the steering or brake system.
View 8 Replies
How do you get the line back on to the rack? There is absolutely no room and I have experimented with a variety of tools with no luck. What's the trick?
View 1 Replies
Just had dealer repair shop complete power steering fluid flush in Jan 2013. Vehicle now has lost all power steering fluid (April 2013) and dealer repair shop has told me it is due to high pressure hose failure - need to replace & then verify pump condition (dealer repair shop not sure if pump bad until hose replaced to test) for repair bill.. I was told this was not related to repair shop power steering flush because this hose not removed for flush or part of that procedure (at which time a transmission flush & spark plugs replaced (minor tune-up) . Just wondering if any pro mechanic can respond with advice about the relative close time frame these two events & if there may be a probable related reason?
View 4 Replies
I got a 1990 ford ranger 4.0l and is been leaking fuel from where the regulator conects to the fuel line the regulator is new. I cant find a new fuel line.
View 4 Replies
I let my sister borrow my 1995 4 banger Ford Ranger for about a week. To make a long story short, when I drove it home I could smell a really strong gas odor so I pulled into a gas station and noticed gas pouring out of from what looked like the fuel filter area right under the driver's side.
Anyway, it took another 5 gallons to get home and I later crawled under and took a look. It looks like someone grabbed the fuel line and tried to unsuccessfully pull it out of the fuel filter by hand. I could literally see the imprint of the person's hand where they grabbed the line. They had pulled the line so hard that it crimped and split which is why gas was leaking like a water hose.
I picked up a Ranger specific Dorman fuel-line repair kit from Advance and had my brother install it for me as I'm no mechanic. It was fine for a few days and then I started to smell gas again so I crawled under and took a look. There's just barely a small leak coming from the connector barb/union on the kit. Anyway, I didn't know what else to do so I dropped the Ranger off at a local shop this evening. With that said, this is fixable, right?
View 2 Replies
My AC went last fall. I saw signs of a leak in the high pressure line. Took it to the Nissan dealer last week and they diagnosed the same problem. They changed the HP line. Told me it was good, but when they pulled it up, no AC. They took it back in and said the low pressure line was leaking as well so they changed it. Still didn't work, although it was a little cooler but the compressor seemed pretty loud. Told me they thought it might be the thermistor. I bought the sensor and replaced it myself. AC seemed to work, but sure enough, it only blows slightly cool air and the compressor is still making a bit of noise.
View 2 Replies
I have a 93 Ranger xlt and after checking wheel cylinders and calipers first I have found a leak that is coming from the brake line or maybe the RABS module. The leak is up along the inside of the frame and I can't get in there because of the gas tank. Has to change line or RABS in that area and am I correct in thinking the gas tank has to come out to do anything in there.
Also, in the manual it says to plug the line as soon as you remove it(at wheel cylinders etc) so the fluid does not leak out of the RABS because it can't be bled without an expensive piece of equipment. I am pretty sure it probably emptied due to the leak location.
View 3 Replies
So, I just found out that the noise my car has been making is related to the power steering. The mechanic said I need to replace the pump, two belts and the high pressure line. The car is a 1993 Honda Accord LX. I can't afford to have the mechanic fix it, so I'm going to have to do it myself. My questions are:1) how long should it take me? I'm not experienced at all. I was thinking of just doing the high pressure line as a 'warm up' to start. Is half a day wishful thinking? Any tips?
2) The mechanic said the hose is leaking all over the belts. He said it was "squirting and pouring out". I tried to duplicate the squirting by turning the wheel all the way and revving the engine. What I saw was a very small leak at the joint. So small it wasn't falling, but I'm sure it would if I waited long enough. The belts appeared dry to me, but I'm not really sure what they are supposed to look like. The mechanic said that they are getting soaked in fluid and that I might throw a belt. Anyway, so my question is how can I tell if the belts are "soaked in" steering fluid.
3) I've been told that if the belts are getting steering fluid on them they might be responsible for the loud squealing noise when turning. If I clean the belts with degreaser, and the noise stops, does this mean that replacing the leaking hose would be sufficient?
I'm making a long road trip in about a week (ca to wa). I'd prefer to deal with the replacement when I get to wa, but I also don't want to make things worse.
View 1 Replies
I own a 03' 2.7 Santa Fe (2wd) and when I got home last night i noticed that she was smoking like crazy (not overheating). Opened the hood looked under the car and noticed some fluid spraying on the the exhaust and leaking down from there which was causing the smoke. I put her on jack stands and noticed what looks like to be some hard (i think pressurized) lines that are attached to a connector of some sort in front of the steering rack. What lines are these? Power steering? oil cooler? Transmission related? The fluid that is leaking looks like transmission fluid cause its reddish brown. Ive worked on a few other cars before but not too familiar with Hyundai. When i get home later I will take a pic of this area and post a picture. And it looks like its spraying from the connecting lines (maybe a crush washer gone bad? ) not sure. I can't seem to find any image of this area online either.
View 2 Replies
I have a 1990 Ranger with a 4.0L that I just changer the intake gasket on. I broke the fuel line at the Fuel Pressure Regulator. Cant seem to find one anywhere. It is a nylon inside/rubber outside with a cloth mesh and quick connect fitting line. Where to get one? Can I hose clamp it the FPR by cutting off the connector that broke?
View 1 Replies
I have a 94 ranger 5 speed xlt v6 4.0l 288k miles original engine. in the last month the oil pressure has gradually gone way up. a manual gauge shows 65psi at cold start ( in the 90* out side) after a minute of idle it dropped to 60psi, at 2k rpms the psi was 85+. also the water temp has gotten hotter to the point of almost being unsafe. it appears that in the hotter part of the day the psi goes higher. the oil and filter was changed 1200 miles ago. the cooling system has been update in the last year with a new radiator new thermostat. no cross contamination in the fluids, engine runs good other than gauges on dash showing water and oil getting close to unsafe range and manual gauge showing high pressure.
View 14 Replies
Made a trip to the hardware store yesterday. When I came out, the truck would crank just fine, but wouldn't start (98 4.0L 4x4). Tried adding gas, no luck. I had actually called a wrecker, but it eventually started after sitting for about an hour. All I did differently was hit the gas pedal a couple of times. Thinking it may be a low fuel pressure problem, I took it to autozone this morning (started it about 4 times now with no problems). Checked the fuel pressure, and it sat at a solid 65 lbs at idle. I tried holding the throttle open and it stayed at the same pressure. I forgot to try with the vacuum off.
First off, I've seen some people say 60 lbs is right, but more say it should be at about 45lbs. 45 seems right since the fuel return is on the block, not on the pump. I'm guessing the fuel damper went out, but is there any good way to check it? Also, since the damper is vacuum controlled, would a bad vacuum cause this problem? Third, could high fuel pressure cause it to not start? That's the one I'm most worried about what was wrong there.
View 14 Replies
I've found everything there is to know about disconnecting the high pressure oil STC line from the oil rail on the early 6.0's, but I can't find anything about reconnecting them. Do you simply press it back on? Should there be an audible "click"?
View 14 Replies
I need to replace my pressure line on my 02 Escape 3.0L. Looking for a DIY for doing this same job?
View 1 Replies
I own a 1990 Ford Ranger, 2.3 EFI with an 8 Plug setup and 2WD. It uses a dual-coil system an not a distributor if that means anything here.
Okay, so for the last week I have been experiencing extremely high oil pressures. My gauge would read almost as high as the "H" mark. The smell of burning oil was heavy in the cab from the vents. I took it easy, made sure my oil level was good and I had enough oil, the truck drove rough, but drove decent.
Yesterday, I got done sliding in some mud (not crazy bouncing or anything, just sliding). I stopped at a stop sign, turned around and hit the gas, and the truck died. I thought there were other issues not related to oil, however I noticed that the oil gauge now read about an inch left of the "L"ow mark. If I turned the key, to the "ON" position, the gauge pushed the needle to above the left gauge itself pointing towards about the "8 oclock" area.
Now, my truck will not start. It cranks and cranks and cranks with no start. I called a bunch of mechanics and none of them knew what I should do. AutoZone did not know what do, no one did. Some people said that the oil pump itself had gone out and that would cause the truck not to start and would cause gauge issue. Others said that it might be as small as the Oil Pressure Switch. Firstly, I bought a new Pressure Switch. Have not installed it because I cannot find the damn thing.
Where the switch OFFICIALLY is. I have read on Google that it is on the passenger side, at the rear end of the cylinder head. Other posts say it is by the oil filter...
PICTURES:
Without the key in the ignition:
With the key in the ignition, in the "ON" position:
View 14 Replies
My truck lost its exhaust a few months ago and it's on the back list of things for this truck so I've been running it without it. However, my neighbors do not like it so, I frequently shut the truck off and coast in down my driveway to park it when it's late. But anytime I do that, I will park the truck and notice a puddle of ATF(ps) on the ground and the PS pump goes empty. Nearly no loss for a weeks when I don't turn the wheel with the motor off.
View 2 Replies
I have some codes on my ranger 2000 here goes
P0141: o2 sensor heater circuit malfonction (bank 2 sensor 2 )
P0455: evaporative emission control system detected (large leak)
Now I will need to get that fixed cause I don't know where to look and what to look for ... For the leak I know there is a big crack on the plastic where the gas lid is could that be it ?
View 2 Replies
