Ford Ranger / B-Series :: Power Loss When Going Down The Road Now Won't Start Or Run
Jan 29, 2016
So, a couple of months ago, my Ranger lost a lot of power going down the road, and when I came to a stop it died, and wouldn't start. So I got it started by roll starting it, made it to a friend's, and then back home. I've put new spark plugs and wires in, and it needed it, badly, but it didn't work. I got a couple of codes off of it,
P0302- Cylinder 2 misfire detected(which I fixed with the spark plugs)
P1443 - which I can't find a definitive answer for
P0500- vehicle speed sensor malfunction
P0171- system to lean (bank 1)
So, the truck will turn over, and if I give it a lot of gas it'll start at stay started for a few minutes, but then cut off. When it is running it's running very very very roughly.
View 1 Replies
Advertisement
1994 Ranger .. Last wednesday I had to get a jump because the lights where left on. Everything was normal on thursday. Friday morning. I went to go start the truck and notice that it would try once to start and then try a second time and it would start. Today I was driving it. The check engine light came on and when I get the RPMs up to shift up, I would loose all power and have to wait till it gets down below 10mph before I would get the power back.
View 8 Replies
This has happened before on my 98 ranger 2.5. You can drive it 10,000 miles without any issue and then all of a sudden you take off and there's no power but it quickly returns. Within the last year I've changed fuel pump assembly, fuel filter, injectors, cool packs, and plugs. Is it mass air flow? It seemed to happen a lot more after I cleaned it. My scan tool is amateur but it has a maf reading in lbs. What should it be while driving? Fuel pressure is always between 65-72 when I check it within specs according to my book.
View 10 Replies
So I got everything fixed on my 94 ranger so I thought. Now it runs right on the "L" on the idiot gauge on 90 degree plus days running the AC. Also it seems to lose power at times and not even want to do 70. I think new coils, new plugs and wires may work. I also have an intermittent check engine light that pops up on occasion, but clears when you kill the motor and start it back up. I was really starting to like this truck despite it not being my style(I like square body rangers) and it being a 4 cylinder. I like the MPG but am starting to think the 200k engine may be fading
View 14 Replies
Bought my third 88 ranger today, drove it 55 of 60 miles home and it died. It lost power and acted like the coil was going bad. This one is a 2.9 5 speed 4x4. The a/c compressor is gone; but the 365 a/c works okay, or did.
My daughter was following me in her car; by the time we got back with my F150 and a chain, it started and ran until it was a half maile from home then lost power and died again.
Drug it home, put a new coil on and it started and revved up fine. Went to move it a couple of hours later and it will crank with the starter, but not fire.
I am getting 12 volts to the primary side of the coil, is there any way to check the TFI module without taking it off the distributor? (they are so accessable).
Or is there something else that I need to check? I really don't want to just throw money at it, I like to know for sure what is wrong before I buy parts.
View 1 Replies
Background- 2000 Ranger, 3.0L 2WD 170,000mi. This truck is not my daily driver, i try to drive it once a week.
I've never had this issue before... I drove all over town yesterday; multiple stops, no issue. Today i go to do the same thing and upon accelerating out of the driveway i lose all power for about 3 seconds. I get power back for about 3 seconds then lose it again. This continues for as longs as i'm driving. Also, no CEL. I go back to the house to look things over, can't find anything staring me in the face really.
Truck idles fine and the issue is not present when i run up the RPMs in park. I've been reading some other threads about similar issues and most replies begin with checking the regular maintenance stuff i.e. TB, MAF, IACV, pcv, etc. It seems like a complete loss of fuel or spark...but only when in gear with constant throttle???
View 14 Replies
My ranger sounds like it's revving up real high when I take off but don't have much power. Know what this could be?
View 5 Replies
2002 ranger edge 3.0 5spd. Truck idles perfect, but when you get rolling and higer rpms feels like the engine is missing. loos of power and shakes. I replaced the usual, plugs and wire's, seemed to work for a bit but came back. I cannot get any info on the scanner and have checked all the fuses. I am thinking coil pack but don't understand why it idles perfect and only misses under acceleration. No check engine light on.
View 5 Replies
My brother's 87 ford ranger 2.3L truck began to have problems. It would be running great, then start to misfire, run rough, sputter, shake and loose accelleration then die. Then it wouldn't start back up for a long time, sometimes til the next day. Little by little, the truck would drive a shorter and shorter distance between breakdowns. He first tried some minor work himself, (basic tune up) - replaced his rotor, cap, plugs, air filter, fuel filter, but that didn't fix it. He went to one garage (big mistake), who said the fuel pump pressure was fine but said he found a broken wire on the harness grounding out and it needed new ignition module and replaced it. (Cost was $350.00+), Garage promised to honor any additional work nec if it continued to have the same problem, and would be free of charge.
Five more breakdowns later and two more "better quality ignition modules", new battery terminals, and 1 new computer later, this joker did more unauthorized work and demanded another $200+ besides the fact of breaking his orig agreement "free of charge" if any further problems! Needless to say, second garage fixed the truck by replacing the magnetic pickup, part # DU 30-C (an electrical part that goes in the distributor and pulsates a current to operate the timing) (it does something like that) and the truck has been driven approximately 40-60 miles as of today, (3 days later), without breaking down. All the other times when picked up from incompetent garage, it wouldn't go more than 1 - 7 miles before breaking down and each time they didn't fix it.
View 4 Replies
I recently picked up a 93 ranger sport 4x4 with 2.3L engine and 5spd.. Has run fine for the first 2 weeks of ownership but yesterday morning, it started cutting out on the highway. When I say cutting it is like all loss of power for a brief instant and then it right back without even losing any speed, I could watch tach drop from 2500 to 2k and then right back to 2500 again..
Did it sporadically all the way home about 10 miles sometimes once in a mile other times 6-7 times in a mile. Truck has 126k on it, and within last 26k miles PO replaced timing belt, coil packs, plugs, wires, ICM, and just before i picked it up from him a new EGR and fuel filter.
No check engine light
Fast forward to this AM
Wouldn't start at all, i can hear fuel pump spinning and she cranks and cranks but no start up.... played with multiple things including the ICM but found 2 of 3 heads rounded off so i cant remove it until i can get it in to my garage and dremel those suckers off..
Went and bought a replacement ICM figured i could plug it in run a ground from the bottom left hand bolt hole so i could get it fired up and in to my garage.. plugged the new one in grounded it and it still wouldn't start...
So I decided to replug the original ICM back in and grab my spark plug tester, remove number 3 plug wire on passengers side insert the tester and have my wife crank it over and wonder of wonder it fires up...
shut it down remove the tester and have her start it up again and it fires right back up so i let it warm up for 15 minutes.. grab my autoxray.. shut it down hook up the scan tool and run the KOEO scan.. gives me a passed 111 code... OK lets start it back up and run the KOER test.. wont start back up.. reinstall the spark plug tester to #3 wire and NOW it has no spark..
View 6 Replies
2000 Ranger 2wd 3.0 ... I bought my truck last summer for $1k from my neighbor, it has hit a deer so the grill is busted,front drivers fender bent up and bumper is bent all to heck. The old girl is rock solid reliable though and gets decent mileage with cruise heat and ac so I'm happy.
Anyways on to the point, I am having two big issues with it, the check engine light randomly comes on and causes it lose power sometimes at others you don't notice it. I have not been able to get codes read because it goes off every single time I go to someplace with a scanner. The light will usually go off if you floor it for a long stretch maf maybe?
The other issue is the transmission, I don't know for sure which tranny it is but the overdrive button does not work at all even though the fuses are good and when I drive down the highway second gear you have to let off for it to shift sometimes ( I've been leaning towards the valve body gasket for that) and lately it has started a horrible vibration kicking out of overdrive or just downshifting on hills etc.?
I forgot to mention it has 255k miles on it and I don't know the history besides the balljoint I replaced this week and radiator when I bought it.
View 3 Replies
Ok I've been plagued with this very random misfire/power loss/hesitation problem going on a couple of months. You could drive the truck anywhere from 50-300 miles without having an encounter of this problem. It seems to do it now mostly on contiguous long trips over like 30 miles. It one time threw up a P1131 code which quickly went away on it's own. This is a list of stuff that has been recently changed: plugs, wires, coil packs, air filter, pcv valve, fuel injectors, tps, idle air valve, MAF cleaned, fuel filter, and egr valve.
I sprayed with brake cleaner for vacuum leaks around the intake tonight after driving a continuous 50 mile round trip it messed a few times on the way back. When I sprayed the EGR valve mounting area it idled rough when it was hit with brake clean and idled up. So there's a leak there. Or is it stuck? It will be driving normal and usually when you come to a stop the engine will start missing really bad and then when you take off there's no power at all. You keep your foot on the gas and eventually it will feel like all the power is just turned on.
If it does it while you're driving highway speeds it will feel like you've lost a cylinder but it's not as dramatic as when you come to a stop and it starts missing. I can't be 100% but I don't think the EGR wasn't leaking before I replaced it and it was still doing the same thing. I'm wondering why the Check Engine Light won't pick up an obvious misfire when you can you actually feel it. And why if it was the vacuum leak would it only start doing it after many miles of driving?
View 11 Replies
1993 3.0 V6 5 Spd ... Changed plugs wires Cap and rotor put in a new idle control Valve. No Check engine light. When i am running down the road feels like it surges,hickups, while its at idle the motor shakes like no tomorrow. Just dont want to throw money at something and not be the part that was wrong. Truck has plenty of pickup runs like a raped ape going down the highway. seems when i accelerate the miss clears up and not there. RPM gauge needle has some movement in it. Also put in K&N filter fuel filter as well.
View 6 Replies
My problem is wih my 1996 Ford Ranger XLT 6Cyl. 4.0L 2WD Recntly it started shaking violently in the rear as I drive down the road any road. Mainly slow to about 50MPH or slower, it just starts to shake really hard and then it stops then out of the blue it will do it again I thought it might be the back Drums maybe the shoes came apart and were catching but they are fine everything looks fine, could it be the gearbox on the axle? I don't know...
View 5 Replies
I have a 2007 Ford Ranger 3.0TDCI when I drive on a road that is bumpy or on a ground road the ABS light keeps coming on , sometimes it just flickers other times it keeps on for about 5minutes. I when for a service 3000km back but they told me the brakes is fine. What it can be?
View 1 Replies
Just got home from work with my 2009 ford ranger XL 2.3 and it was running fine, went back out 10 minutes later and it would not start. No clicking noise from the solenoid or anything. Tested the battery (12.8volts). checked all the cables, checked all my fuses and everything is good.
Then noticed I have no power to my headlights, brake lights, or instrument panel. The only power I get is to the horn and the interior light. When I try to turn my headlights on or turn the key to different positions the "smart junction box" at the passenger side kick panel starts clicking. (there are no relays on this thing)
I decided to check the battery when the key is in the start position and the voltage dropped to 5 volts. Power is going somewhere but I am completely lost here.
View 2 Replies
I am working on my buddy's 1994 Ranger with a 2.3L I4 that has been going thru a large amount of engine coolant. The trucks has approximately 180,000 miles on it. When I had it parked on concrete I have not seen any signs of coolant on the concrete or any signs of coolant leaking. The next place I checked was inside the cab to see if there was any coolant from the heater core and there was not. The water pump has been replaced a couple of years back. I replaced the spark plugs today and did not see anything on the plugs that I would have thought were signs of coolant in the combustion chambers.
With that being said I have not worked on a vehicle with a leaking head gasket before. Would there be any visible signs on the sparks plugs? If so what would I be looking for? When standing in front of the vehicle with the engine running there is a slight smell of antifreeze being "vaporized". Are there any noted issues with this engine that would cause this? Are there any other things I should check? Could it be a leaking head gasket causing this? If so how can I check for that?
View 1 Replies
ok so let me start by saying, my name is Tim, I own a 1999 Ford Ranger 6 cyl, 3.0L truck, I bought it brand new in 1999 and drove it for a few years and then took it off the road for 3-4 years then last year I went to put it back on the road and I couldn't get it running.
I took it to the dealer and they replaced a key switch module. since then the ranger seems to lack power. It also idles erratically when you first start it in the morning too.
not sure whats going on here but the engine light is on,
I get codes P0171 & P0174 (too lean bank 1 and too lean bank 2)
I would also like to note that I have replaced the fuel pump, fuel filter, transmission filter, MAF sensor, IAT sensor, PCV valve, EGR valve, TPS sensor, idle control solenoid, fuel pressure regulator & new plugs. I have also checked for vacuum leaks with no avail.
View 6 Replies
I have a 2009 f250 with 70,000 miles on it and for the last 6 months I have been experiencing some power loss. It happens every time there is the slightest incline on the road, it has to down shift to 3rd gear just to maintain that speed. If I don't push on the pedal until it down shifts to 3rd I slow down to 40mph no matter what the speed was before I hit the incline/hill. I also went from 14 mpg to 10.5mpg. I have heard so many theories and am curious if the fact I upgraded to 35 inch tires and never updated the trucks computer.
View 10 Replies
Really scary, had my son in the car. Dash read "Check hybrid system". Reading some posts make me think that it may just be the 12V. Had it towed to my house.
60k GEN3 2010 Prius III
View 19 Replies
This just recently started happening just shy of 200k miles, 14 years. While driving down the road, suddenly notice a power loss or no power, i.e., no motor output. Sometimes the just the ICE won't accelerate, sometimes it's both ICE and Electric motive force. When this occurs, the Brake and ABS check lights turn on. After a few seconds, to 10's of seconds, then the motive power reenables and the Brake/ABS lights go out. Often the cars continues on with no repeat. Testing over a few drives, it seemed to only do it during the warmup cycle when coolant was near 160-170.
However on a drive in the afternoon after it occurred in the morning; with ambient around 30 degrees, windows cracked, interior heat off, it didn't occur on the 15 minute drive, mostly freeway speed, even after about 10 minutes and cranking interior heat on. No codes are registered when this happens. I used Torque Pro and monitored things like throttle position and such, and things there seemed normal. Eng rpm dropped under 1000rpm and wasn't steady. Watching the MFG the power flows responded to the throttle (pushed/released) as if the engine was still doing what was asked (go figure, the display shows what is commanded, not what is occurring?).
View 7 Replies
