Ford Ranger / B-Series :: Passenger Middle Of Floor Wet When Raining
Jan 2, 2017
I haven't ever been able to figure out why the middle of my passenger floor board gets wet when it rains or I go through a carwash. It's definitely not a heater core leaking. I don't see or feel any moisture under the seats further back or further up near the cowl, or roof. It's exactly in the middle of the passenger floor. Is there a plug under there? I've yet to pull back the carpet to look. I plan on eventually replacing the carpet but I want to figure out what the water is. It gets a musty smell because of the water. It's not a lot of water, not a puddle, just you can lift up the floor mat and see the moisture on it. So it's under the carpet. Windshield was replaced 3 or 4 years ago.
View 6 Replies
Advertisement
Ok I got the brake pull fixed (I think) on my 92 Ranger 4x2 4.0 extended cab. I still will have to change the driver's side brake hose for prevention and the driver's side caliper just so everything will be new. But it stops straight now with a new brake job, pass caliper and hose on. However, this other problem has been ongoing and it does it on my 1998 Ranger too. It's not the heater core.
I think the evaporator case is filling with water and dripping down under the carpet. So the drain tube must be stopped or the case must have a bunch of leaves stopping it up. But where is this tube you're suppose to check? I don't see a conventional drain tube I only see a blower motor vent tube that doesn't drain to the outside of the car anywhere. I know my 73 Charger has a rubber drain tube that comes out of the evaporator case and drains onto the ground. But where is this one on a Ranger or what else could it be? It's only the passenger side so it's got to be that.
View 2 Replies
2000 ford ranger, 2.5 2wd
Been having a little problem whenever it rains, the carpet on the passenger side gets soaked through and I'm not really sure where the leak is coming from. the only part of the floor that gets wet is the flat part where the passenger would put their feet, but the parts that slope up towards the dash and towards the middle of the cab stay dry. I've pulled up this part of the carpet, and the rubber grommets are intact and in good shape, and there is no rust or anything on the floorboard. from searching here it seems people have had similar problems, one thing being a leak into the seals around the third brake light above the rear window.
a couple things i should mention is that the air conditioning condenser has been broken for about two years, so could water get blocked up and leak in? since its winter here in PA i haven't used the air con since last summer though. I'm not really sure how long the leak has been happening since I've always kept a floor mat over that spot, and the carpet drys in a few days anyway.
Another thing i should mention is that the weather stripping at the bottom of the window on the drivers side door is not perfectly tight and tends to come out of place when the door is closed hard. this has been happening since i got the truck almost three years ago and a new piece was just put in a month ago (the leak had been occurring before the new piece was installed) when the truck was hit and went in for body work. possibly a drain routing to passenger floor? I should add that I'm sure it's not coolant, it has no odor and feels like water.
Might be a good idea to pull up the whole carpet on passenger's side and sit in the cab during the next storm...
View 9 Replies
Whenever it rains a substantial amount, like all day I go out to my 92 Ranger and get in and notice the passenger side rubber floor mat has a puddle of water on it. I look under the floor mat and only the center of the carpet there is wet. I see it's getting the edge of that side of the headliner wet and ruining the new headliner had redone. I didn't realize there was water leaking until I got my headliner redone and put back in. It very well could have been leaking causing the headliner cloth to all tear. It's wet along the top passenger side where the grab handle is and the plastic trim. I thought it was the rain gutter on top of the roof so I put in some black silicone and some of it stopped but not all.
So I thought it was still leaking at the front corner so I put more silicone in. Don't know yet if that was what it was for sure but I'll find out tomorrow because it's raining pretty good right now. But just in case where else could it be getting this much water in. If you go through a carwash, or hose it down for awhile, or even drive while it's raining bad it won't get water inside. I'm not convinced it's the rain channel 100% because on the driver's side the putty filling the rain channel on the roof looks worse than the passenger side and there's no water coming in on the driver's side. There is no water coming in the back or on the back carpet or headliner.
I don't see any evidence around the windshield. I can't understand why only the middle of the passenger side carpet is soaked and not the top or under the seat, unless it's just soaking through the rubber floor mat and not drying out. It's getting so frustrating because I can't visibly find any evidence, I have to wait until it rains and then I can't see why it happens. It's ruining my carpet and my new headliner. I want to replace the carpet but want the leak stopped first. Where are common trouble areas on these 92 Rangers for water leakage?
View 14 Replies
I have a 97 Splash with the 3.0, oil pressure goes up to about the middle of the gauge after startup, however, it stays there whatever I do, warm/cold, idle/5500 rpm. Is it supposed to be like that?
View 4 Replies
Drove ~1500 miles this week, from MN to MA. While driving through PA my left headlight died in the middle of the night while raining. I ended up fixing it after spending an hour at a gas pump for shelter. Also in PA I randomly stopped.
View 14 Replies
When we have a heavy rain water leaks in on both sides saturating the floor board.
View 2 Replies
1997 Ford Ranger w/manual 5 speed tranny
A few weeks back my clutch pedal seemed a bit softer than usual one day. Still it worked fine... no problems shifting. Today after a short ride it went almost to the floor before disengaging. Now I cannot get it in gear without grinding.
So cold out I'm not sure I want to tackle this right now, what to look for and where?
View 14 Replies
My buddy called and said his clutch pedal went to the floor on his 04 4.0 ranger. Said no fluid leaks or anything, so I suspect the slave cylinder went. He said the slave is on the inside of the trans and you gotta pull the trans to do the slave, so might as well do the clutch too. How hard is it to replace both these on this truck? I've done it on a 94 cummins, so the trans should be a lot lighter. just wondering how bad of a job it is to do?
View 2 Replies
1999 ranger 3.0, 5 speed stick. I was backing out of my driveway but there was a car coming so i pushed in the clutch and waited for the car to pass, when I let clutch pedal up off floor i heard a grinding noise, a little while latter did the same thing in first. Is this a first and reverse gear scyronizer or something else. What causes this and how to fix it ?
View 10 Replies
1999 Ranger xlt, 4 cyl. 2wd reg cab, automatic. Getting a rumbling noise with some vibration in the floor ( nothing in the steering wheel, does not seem to affect handling ) runs consistently and relative to speed of vehicle......can not isolate or determine origin of noise.........
When initially driving car after sitting for awhile, the noise does not kick in until 50 to 100 yards have been traveled but is consistent thereafter,.....except for.. completely disappears during taking of left handed curves at good speed but reappears when road straightens...... right-hand turns have no affect positive or negative.
Have thrown into neutral at speed and sound and vibration is unaffected,.... brand new tires ( needed them ) with balancing had no affect either Struts, shocks, springs?
View 4 Replies
Installed a new clutch and slave today. Kept the same master cylinder.
The problem I am having is that the clutch pedal will not go to the floor, and therefore the truck won't start. The slave is moving back and forth roughly 3/8 inch, maybe more. I am pretty confident that there is no air in the system.
If I loosen the pressure plate a little, the clutch will go to the floor. But tighten it back up, and it again only goes down about 75%. This is a late '95 so it has the self adjusting clutch. I did get the correct kit for it, as well as slave. It's like the self adjusting part is too far adjusted and won't let my slave travel as far as needed.
In troubleshooting, I did notice that I failed to get the dowels in the flywheel aligned in the pressure plate. I am old school and not used to dowels in the flywheel! The dowels are not hitting anything and are not preventing the pressure plate from seating on the flywheel. But it is something I'm going to fix if I have to pull the trans again.
For reference, I replaced the clutch because the slave cylinder was hanging up and preventing the clutch from getting fully released. Aka clutch slipping.
View 6 Replies
in my 2008 ford Ranger Sport with a V6. The smell reminds me of one winter when I had stepped in dog and didn't know it until I was four miles down the road and the heater was on full blast. The smell floods the cabin when the heater is first turned on and warms up, but dissipates after a while. (And I don't have dog on the floor boards or on my boots.)
The smell does not come out the AC vents or when the AC was operated this past summer.
View 3 Replies
acts like abs sensors could be bad. but the brake pedal goes almost to the floor, after it does it's pulsating. But the abs light does not come on. I already changed brake booster, no change!
View 5 Replies
Returning to the VW fold. Just purchased a 03 Jetta GL (NO SUNROOF) and after the first rain, the passengers floor board is wet. I have searched the forums and have read many threads about the sunroof drain. Where else could this be coming from? I had a BMW that would do this because the vapor barrier in the door came loose. Is this the same situation? I looked at the panel at the bottom of the windshield and it looks tight against the glass and do not see anything stuck in between the panel and the glass.
View 5 Replies
In my 2006 Ranger XLT, 4.0L V6, 2WD Manual; I am getting vibration from what appears to be the passenger front. I have so far replaced the front wheel bearings (both sides), replaced front shocks and checked rear shocks, rotated tires (to see if it changed) and had front tires balanced. I've also had a friend follow me on the freeway and check the wheel to see if is bouncing, wheel appears to be glued to the road. I have done all the front suspension checks I can and find no indications it is the lower ball joints or tie-rod ends.
This vibration is very in consistant, in different lanes it is better/worse. At times I feel it more in the steering wheel, others my seat and at times the gear shift. I don't believe it to be the engine mount(s) cause when it is vibrating I can shift into netural and the vibration does not change, I have also performed the 5K rev (FORD maitn. manual) and the engine is smooth (along with my expierence with bad mounts in my '94).
View 11 Replies
I have a problem with my 2002 Ford Ranger XLT Super Cab's passenger window. It seems like it has a loose connection, but I am not sure what the exact problem is. When I try to move the passenger window from the driver side control panel, nothing happens. The driver side window works fine. On the passenger side control panel, I can hear the motor trying to move the window when I try to put it up (the window is already up).
When I try to put it down, I hear nothing unless I push the button repeatedly - anywhere from 3 to 20 times. When the window is partially down, moving up always works, but I have to keep trying to push the button to make it go down. I have tried pushing down on the window while I press the down button and spraying white lithium grease in the window tracks while the window was down, as well as pulling part of the seal away from the window while I tried to make it go down.
View 5 Replies
I have a 07 Ranger and the passenger door sounds loose when I hit any bump. Where should I start to make any adjustments on the door?
View 3 Replies
Well, I had a friend put together my front brake rotor, now no more pulsating when coming to a stop, very smooth stop, new front brakes, had it aligned as well.. Also replaced the front shocks, however the passenger side came loose and rattles when going over bumps, speed bumps. I popped the hood, bounced my truck and could see it moving from left to right when bouncing front end of truck.
Question is, can i tighten it up myself, I dont have a jack, limited tools, I know, I know but i dont at the moment. My friend that worked on my truck lives a good drive and i hate to waste gas just for tightening something that should have been done but i have too, I will..
View 3 Replies
i have an 89 ford ranger custom and my driver side tail light works just fine but my passenger doesnt work when i mash the brake the passenger side brake light wont come on. the parking lights work, turn signals, and hazards work but the brake light. ive checked the wires and replaced the socket and still the same problem so either theres something in the wires that im missing or i dont know what else. any hints?
View 7 Replies
Is it what it looks like? Why is it there, to pressure bleed the system through it rather than using a modified MC cap?
View 5 Replies
