Ford Ranger / B-Series :: PS Leak And Pump Goes Empty When Steering With Motor Off
Sep 10, 2017
My truck lost its exhaust a few months ago and it's on the back list of things for this truck so I've been running it without it. However, my neighbors do not like it so, I frequently shut the truck off and coast in down my driveway to park it when it's late. But anytime I do that, I will park the truck and notice a puddle of ATF(ps) on the ground and the PS pump goes empty. Nearly no loss for a weeks when I don't turn the wheel with the motor off.
View 2 Replies
Advertisement
I saw a nice very clean 2011 ranger with 63,000 miles on it . But there looks like it has a oil leak on the upper right front of the motor. Behind the pulley that does not have any groves in it . It could be a gasket or a oil seal I don't know. Is this oil leak something common with the 2.3 engine?
View 4 Replies
My ranger decided to start leaking fuel somewhere probably a few weeks ago. I can smell it whenever I start the motor, and sometimes while driving with the windows down. Last night, I finally looked into the problem. I took the intake air hose off. The hose, air filter, and whole intake smells like gas. I'm thinking that shouldn't be the case on a fuel injected engine. After seeing some people talk about the Fuel Pressure Regulator go bad, I pulled the vacuum line off of it, and it has a very strong gas smell. I don't see any gas coming out of it, though, even with the motor running. Everything I read says if the regulator is bad, then gas should come out of the vacuum line. Is there another check I can do on it to confirm this is the problem? Is there somewhere else I should be looking? It got two new heads right before this problem started, so its quite possible I knocked something putting it back together.
View 6 Replies
Truck quit running yesterday suddenly and unexpectedly. It sputtered briefly and the motor total quit running. I pulled over and tried to start and it briefly fired but then totally quit. Got towed home. And now testing to see what all to repair..Thinking fuel.
I don't get any codes from the tester with KOEO..just the good to go etc..no codes or the good to go 111..etc. Guess this problem can't be identified without motor running.
My wiring diagram doesn't give me all for my Calif car..I don't see where the relay is but my fuses are all good, and I'm getting voltage when I crank the motor at that inside firewall switch on both its wires(incoming/outgoing)..forget what its called..Inertia Switch?..that will shut off fuel pump during accident or impact etc. And I've read that this switch is upstream of the relay(if I read that post correctly) so guessing it's the pump itself that is bad.
Does that sound right? Should I go ahead and pull the fuel tank etc and replace the pump? Or is there more testing I should do? When I turn the ignition key on..the pump makes zero sound. That's not the way it normally operates. Usually with the key on the fuel pump comes on momentarily and I can hear it. Forget how to drain the fuel tank etc..I don't see a drain plug? I did it once many years ago..but forget how?
View 7 Replies
One last issue with my 2000 B3000 3.0L. The leak seems to be on the left (passenger) side of the water pump very near where the bottom radiator hose connects to it. I can't find any loose bolts. It does not leak while driving the truck or soon after. It has to sit for several hours or overnight before it shows up. There are usually 3 or 4 wet spots where it drips from the water pump to the frame to the driveway. It is small enough that I only have to fill up my coolant tank every 1 or 2 months. Could this just be a small gasket leak? It's been happening for about a year or so I think. I replaced the radiator about 2 years ago. I've been expecting it to get worse or bust loose and have been checking it very often. I've never seen one not leak while running like this-has me puzzled.
View 6 Replies
I have an '04 Ranger Edge 3.0 with a severe coolant leak. It appears to be coming from the area where the head/water pump housing meet. I have been told I've lost the seal behind the pump on the timing cover. Is there any way to know for sure? Will I be able to tell, once the pump is out that it isn't coming from the head side? Are there any "special" instructions for re-sealing after replacing pump?
View 6 Replies
I think I've tracked my power steering leak to some type of sensor on the pressure line, close to where it connects to the steering box:
I assume this is a pressure sensor? I got no CEL or anything like that when the fluid had leaked down to the level that the pump started whining pretty badly though. As far as I can tell by looking at pictures, the parts store replacement pressure lines do not have this sensor, or any provision to connect a sensor to it: Advance Auto Parts: Power Steering Pressure Hose by Powercraft - Part 71878
I may just put a replacement line on there and leave the sensor plug hanging and see what happens...
View 11 Replies
Any known problems with '94 Ranger/B2300 gas gauges? I just got a '94 B2300, and gas gauge reads empty with the key ON, and about 1/4 tank with the key OFF. Was told by previous owner it occasionally works, but I've never seen it work. Am starting to procure manuals and dig around the truck myself, but don't want to re-solve the problem if it's a known one. Haven't seen mention on the net of it being a recurring problem, but just starting to dig.
View 6 Replies
I suspect I have an oil leak where the oil pump mounts to the motor.
It looks fairly simple to replace, but I was reading in the Haynes manual something about the timing chain?
So I don't know if it's more involved than I think.
View 4 Replies
My MILaw Truck 1992 ranger isnt running good and I need to get it going
Only a P0111 at this time IIRC
We started the truck tonight and idel ok Could see the motor Stumble every so often. She went to drive it and it Cuts out under Load Or you must rev it up to keep it from Stalling.
And if it does Cut out you have to let it sit for 5 minutes to restart what is Weird is it dont Smell Flooded either I smelled the VAC Line to the FPR and it was DRY and Did NOT Smell like Fuel.
It was dark didnt do much trouble shoot as the Flashlight died. I wonder about Fuel Filters. And Also about the Idel Control. The Mis or Stumble seams Random
Any testing I can do I have a DVM and that Code Reader. Might have to find something to check fuel press with where would I check it at the fuel rail I assume. Going to try and go over the Basics tomorrow If there is Anything Specific I should check?
View 14 Replies
How do you remove this clip holding the wiper linkage to the back of the motor? I can't see what kind of clip it is to know how to remove it. Ford says to remove the wiper pivot and let it drop. Is that necessary? I can't barely get to the back of the motor so I'm having to feel the clip and remove it but since I don't even know what kind of clip it is it makes it so much harder. Does the cowl cover not come off or is it just this access panel?
View 3 Replies
1996 Ranger 2.3. I bought it from a friend 2 months ago. 228,866 miles. The motor seems to stumble as I'm going through the gears. I've cleaned the mass air flow sensor and installed new air filter. Check engine light has always been on, O'Reillys hooked up their computer to it and said Emission Valve Malfunction. I see the charcoal canister, then I have 2 electrical sensors on same line. First one from canister looks like what Rockauto.com shows as a Vapor Canister Purge Valve. The photo has it with a yellow orangeish top. I don't know what this 2nd sensor is. It has a blue top.
View 2 Replies
I just changed my front brakes in my 05 Ranger. New rotors, pads, bearings (packed), racers, new caliper on driver side, bleed all for brakes. Now when I am just about to stop it feels like the left front is grabbing. I also hear the ABS motor humming when it grabbs. Don't whats causing it?
View 4 Replies
I have a 1987 ford ranger, it has a 2.0L carborated motor and I also have a 1994 ford ranger fuel injected motor I believe it's a 2.3L, I am wondering if the swap will work to put the 94 motor in the 87....
View 3 Replies
My actuator/motor doesn't have the screws that hold it on. It's just clipped down. Can I just pry it up & off with out it breaking the clips that hold it down? It's a 97 Ranger.
View 2 Replies
I have a 2002 Ford Ranger with a 3.0L engine that is having some issues with starting, here is what is happening.
Every so so often when the key is turned to start there is no movement from the starter motor. The battery is fine and all of the dash lights stay on while the engine is not starting. I have replaced the starter with a remanufactured model (possibly a mistake), and also replaced the clutch interlock switch.
I have attempted to change the ignition switch but the replacement I received did not even try to turn the starter (after many tries), like possibly it was faulty out of the box. I am currently using the OEM ignition switch as it will at least turn the starter eventually. I just worry that this problem will develop further at the wrong time.
View 7 Replies
I've got a new to me 97 Ranger that the blower has never worked in and I can't get it going. I've checked the fuse. That's good. Tested the relay. That's good. Did an ohm test on the power switch for the blower. It's open in the "OFF" position and closed in the other positions. I've got continuity through the speed selector switch. New resistor and pigtail because the other one was nasty looking. What seems odd to me is that I've only got power to the blower motor relay at one terminal with the switch on (number 30 I believe). In addition, when I test the plug for the motor itself with my test light, one of the wires (org/blk I think) has power only when the switch is off. And I ran power straight to the fan from the battery and it spun right up. What am I missing?
View 8 Replies
The fuse and relay have been tested. There actually is 5 volts at the fuel pump. The truck was running OK when the clutch went out. It wouldn't start after the clutch was replaced. The inertia switch is OK. I don't know where to look now....
View 14 Replies
Anyway just got a new fuel pump put in my 99 3.0 Ranger and now after it's warmed up from a few miles it starts to choke and almost die. No CEL comes on and I just put new Motorcraft plugs in and still the same thing. I read something about maybe cleaning EGR.?
View 13 Replies
I recently bought a 96 ranger.I noticed the fan did not work but for high. I search the internet and found how to remove it and discovered a mouse nest(village) which basically took over the housing where the evaportor core,blower motor resides. I bought a chilton but cannot remove the housing around the core so I cleaned it the best I could(air compressor and vacuum and disinfectant)...
I had to buy a new blower motor and resistor. However, I cannot find the hose that attached to the blower motor?-mouse had chewed a hole in the one- I've looked and found serveral differents names for it but seems I cannot find it at my local parts store.
My question is- is this intake hose? vent hose? I'm guessing I will have to go to dealer or, if I know the name I can look it up in a salvage yard?
View 14 Replies
I am not great with electrical but can manage. Here's the deal, Ihave a 1997 ford ranger 2wd 2.3L 5spd with a/c 233,000 miles i just replaced the heater blower motor resistor as the old one was rusted bad as was the pig tail going to it bad that one of the terminals broke off and was rusted in the harness so i replaced the plug as well problem is i still have no fan if i jump it it works but have no power at the plug for resistor or motor and no power at the switch inside the truck I do have power to one terminal where the relay plugs in, where to look next?
View 14 Replies
