My battery went flat and to compound my misery, when I went to open the hood, the cable was snapped. How I can open the hood without using the release cable ? I'd rather not have to pay for it to be taken to the mechanic and then also pay to have the battery changed !
View 3 RepliesSo in order to get my hood to open, I have to pull the hood release lever in the cab, go pull up on the hood itself, then pull the release lever again, and pull on the hood to get it to finally pop. Is this a cable perhaps going bad? Or another issue I need to fix?
View 14 RepliesHow to manage to open the hood when it wont "pop" from inside the cabin. There is not enough tension on the cable and seems as though either the cable has been stretched or either came off or broke its retainer under the hood... I noticed "TSB"s but to be honest I dont know what these really are or how they matter...
View 3 Replieswent out after checking out the cheap mod thread (to see what I can mess with), went to pop the hood and nothing happened. I've looked all over vortex and I cant find anything.
View 3 RepliesI bought 2000 Ranger with rear half of the frame cut and welded.
The mechanics who did this did terrible job of putting things where they belong. I rerouted wiring harness and rebuilt EVAP lines, but cannot figure out what is the correct route for parking brake cable.
Currently some part of the parking brake cable is sitting on the leaf spring. It may also be missing some mounting brackets or clips. Looking for a picture or diagram showing parking brake cable routing?
After taking apart my instrument panel to change the bulbs, I went to reconnect everything, but now the gear shift indicator isn't working. I can change gears fine, and everything else on the instrument panel works just fine.
The copper cable that connects to the shifter doesn't move when the shifter does. Is there a way to fix this problem, or do I need to find a replacement cable?
so i changed the speedo cable and speed sensor in my 93 ranger, but still getting the speedometer bounce. what could be next? the speedo housing in the cluster? lubed the inner cable, made sure nothing is kinked or sharp bends. Put in a new vehicle speed sensor while i was at it just bcuz. cruise control does not hold a steady speed either but i think the 2 are not related. I'm leaning towards the cruise control servo as to why it does not hold a steady speed. Most of the time once i get to around sixty i'm basically driving by ear bcuz the speedo bounces from 60down to 55 and back up.
View 3 RepliesI bought a 2000 Ranger 4x4 3.0L auto today from the neighbor guy sight unseen with a "bad tranny" for $400. I'm very unfamiliar with the Ranger family, but long story short:
When moving the shift lever, the trans doesn't engage. It needs to be engaged from underneath. Do the cables tend to stretch, or break? I can't find any adjustment on it anywhere.
I've noticed my RR emergency brake cable's outer casing rubs hard against the RR shock, such that it's rubbed through the cables plactic covering & is going after the metal jacket.
It's a 99 4X2 4dr extra cab long wheel base.
Notice this on your Ranger, LWB model, or for that matter any wheel base Ranger???
93 Ranger, 4.0 liter, 4WD.....
Putting in a new clutch and clutch release bearing, and am wondering if I need to put the retaining ring in that came with the new clutch release bearing? When I took off the old release bearing, a ring did come off from somewhere, but I did not see where it was because it was so dirty.
The reason I ask is because my Haynes manual did not even mention a ring, so I was surprised to see one come off. And my manual does not say to reinstall the ring when installing the release bearing. I did get a newer Haynes manual at the library and looked through a bunch of Chilton, etc manuals.
The newer Haynes manual says to remove the retaining ring on 97 and newer models, but says nothing about putting it back in when reinstalling. So, I am not certain if I need to put a new retaining ring in with the new release bearing.
So I'm motoring along a country road with the cruise set at 50 mph and the truck starts to increase speed.
Tap the brake - nothing happens. I'm up to 65 mph! Knock it into neutral and it revs to around 3,500 rpms and then it unsticks.
What in the world is going on with that? After thinking on it, a few miles farther on and I set the cruise again.
It began immediately picking up speed. I hit the brake and nothing happened. Then I hit the off button and nothing happened.
So again I bumped it up into neutral and it did the same thing - revved for a moment and then kicked off.
The dealership where I get my service done can't get to it for several days. So I'm checking in the meanwhile to see possibilities to identify a cause.
Started the other day. Seems like the blend door that channels air to the dash vents is opening and closing as it feels like it. Sometimes open for awhile, sometimes closed. The defrost vents keep blowing cold and normal while doing this.
View 9 RepliesDriving home from work (a 30 minute hwy cruise) I had to stop for a traffic light. As was sitting there I hear a thumping noise from under the hood, otherwise it was running the same as always. Got it home and I didn't hear it anymore, looked under the hood while idling, seen nothing, shut it off. top rad hose had a slight amount of pressure, started it and it quickly built pressure and felt a rhythmic thumping in hose and it got fricking hot quickly. I figure either a head gasket or cracked head.
I just recently did an aggressive cooling system flush using Prestone heavy duty cooling system flush (can only get this at a dealer) because the previous own neglected it, and it blew a head gasket, tons of rust inside when I did it. I'm gonna borrow a tester to check for exhaust gas in the cooling system and what did it end up being? The guy I bought it from (the previous owners mechanic) put 1 or 2 head gaskets on it.
1991 2.3 l. Thought I had an exhaust manifold Leak. Replaced gasket. New gasket didn't work. Removed gasket and mounted manifold to engine metal to metal, still and noise. Installed New manifold with gasket. Still same noise. Am thinking noise not coming from manifold. Torqued all bolts to spec. Could it be lifters .
View 9 RepliesI have a 98 Ranger 3.0 with a standard transmission. The truck has 240,500 miles so far. It runs just as good as the day I got it 11 years ago, doesn't use any oil and still gets 23 MPG. Last fall, it developed what sounds like an exhaust leak under the hood. It seems to be coming from the area of the EGR valve. The trouble is that I can't feel it or smell it. I have carefully felt the entire length of the tube running from the EGR to the exhaust manifold and cannot feel any leaks. There is no soot or any other evidence of an exhaust leak.
The noise isn't there for the first minute or so that the truck is running. I would think that if I had a cracked manifold or some other such leak, it would be worse when the engine is cold but this is not the case for me. It is most noticeable when pulling a hill as slow speeds in a higher gear. I have checked for codes (no CEL) and there are none. When I first heard it I figured that I would wait until it gets a little worse and I would be able to find it. Its been been over 8 months now it has remained the same.
fuse #11 in the battery junction box under hood keeps blowing, the last time I put a fuse in it blew immediately, key was off and lights off. Fuse is for parking lights, dash light and I/P(whatever that is) and switch illumination lights. I have to start following all wires to find bad spot. May just put in piece of metal and watch for smoke...
View 3 Replies1998 ranger 5spd... I have 117k miles on this little ranger and I recently took it on a little trip and since that trip it has a ticking noise under the hood as if the lifters were sticking. I believe it has hydrolic lifters in it. I put some sea foam in it 200 miles ago and changed the oil about 50 miles ago. I used Valvoline full synthetic and it seems like it has lessened the tick and it drives a lot smoother, in my opinion. Is there any thing else I can do to relieve that ticking? It is more noticeable when the engine first starts and is louder if i push down harder on the gas. It is not preset if i do not put that much pressure on the gas.
View 6 RepliesMy friend has a 98 ranger that has a lose connection on fuel relay under the hood, Hit a bad bump truck dies, Pop hood wiggle wire and your good till next bump. This got real old real quick. How this connection is made, Is it soldered?
View 2 RepliesI have a 97 Ford Ranger / 2.3L / 4 cylinder (L4) / 5 speed manual / XL Supercab / 140k miles. I had been having some Check Engine issues and ran rough in town stop light to stop light. But was fine on the highway.
On several visits to the parts store, their OBD tester showed:
PO303 (Cyl 3 misfire detected)
PO141 Bank 1 Sensor 2 O2 Sensor (heater circuit malfunction)
PO171 Bank 1 Combustion Too Lean (the most recent new code to show up)
And the following would show up sometimes, but other times not:
PO 402 EGR Flow - Excessive Detected
P1409 EVR (I cant remember the exact error message for this)
Regards the PO141 code, O'Reilly's sold me a Bosch O2 Sensor (Bosch 15719) and the sales rep told me it was the sensor closer to the engine. And with the attached cable length on the sensor showed was indeed the sensor closest to the engine. But I've been advised the Sensor 2 is for the 'downstream' sensor, furthest away from the engine. And the other sensor, that I replaced is the upstream sensor. And the error continued.
Then back issues showed up and I had back surgery this past year and thus drove the vehicle sparingly. Never resolving the check engine issues. (My bad). Ran on the highway ran fairly well. But recently noticed longer acceleration times and unable to top 65 in 5th gear. I bought spark plugs and plug wires and had plans to change next week.
Yesterday as driving down the Interstate, was 90 miles into my trip, I noticed loss of power even in fourth gear. (note it was the hottest day of the year at 100F). It seemed I used more gas than usual for that distance. I stopped for gas on the Interstate and power seemed to improve. Then about 130 miles into my trip I hit some heavy stop and go traffic, and wasn't able to keep an idle and the engine died numerous times if/when I didn't give it gas at a dead stop. The heavy stop and go heavy traffic and the issues persisted for a half hour for more than five miles. Then when traffic opened up the truck seemed to have a bit more power in 4th gear again. And up to that time all my dash gauges were showing fine. Then a couple miles or so down the interstate, driving 65mph in the inside lane, the check engine light started flashing quickly. And at the same time a sudden loss of power, rough sounding engine with heavy white smoke coming under the hood. And looked back in rear view mirror, with nothing but heavy white smoke. Managed to cross three lanes in heavy traffic and was able the vehicle to the outside emergency lane, finally coming to a stop.
Looked under the hood and saw oil dripping everywhere but with all the oil everywhere I could not find a prime source. Looked like the oil came from the top end of the engine and dripped down. Measured the oil at the dipstick and it seemed like I was at least a quart plus down (I checked the oil before I left on the trip). And it didn't look like any water was in the oil. And my radiator overflow tank was at the proper level. So I figured I lost all that oil during that period of "white smoke".
So had my vehicle towed home. Today in daylight, I did some more inspection and removed the air intake system (hoses and canister) from the air filter to the throttle body. There was significant oil up to the canister piece that fits on the air filter canister (but no oil in the actual air filter), and significant oil inside all the hoses up to inside the throttle body (up to the butterfly which I could see),
When I disconnected these hoses I noticed the blow-by hose connected to the intake hose system was not connected to anything. And a tube opening on the valve cover was open without the a blow-by hose attached and, with no clamp. So I assume all that oil and came out of that blow-by tube on the valve cover, (white smoke created by hot oil hitting the engine).
So appears to me that its not a blown head gasket or worse, which I first feared.
I have the vehicle parked at home.
QUESTIONS: So what are the suggested steps to troubleshoot and repair? Besides reattaching everything and putting a clamp on the blow by hose? And installing new spark plugs and plug wires. I previously replaced plug wires around 60k, even though the manual recommended 100k mile replacement. (And a couple yeas back I had the dealer replace the PCV, which was recommended in the manual and included in the warranty. The timing of the initial check engine lights appeared shortly thereafter).
Is there suppose to be a large amount of oil in the air intake system after an incident like this and should I try to clean/flush out the hoses and the inline canister?
When I disconnected the inline canister from the hoses in the air intake system, unfortunately I failed to document the direction which the canister goes. It has outside markings "ADP with a forward arrow with some horizontal lines, and then at the other end upside down markings with a greater sign PP less than sign. Should the forward arrow point toward the throttle body or toward the air filter (I'm thinking in the direction of air flow, toward the throttle body). I've taken some photos of the engine with air intake hose system unattached, if that might work...
1999 XTL 4.0 auto, was doing fine, replaced Interior light bulb, now wont crank over!!! i suspect the anti theft system... how do i fix or ByPass the security system, i can start the truck by Manually engaging the starter Relay under the hood.
View 1 RepliesI have a 2006 Ford F-150, and when I pull the hood release, the hood won't open unless I'm holding on to the hood release handle while pulling up on the hood. I've been trying to figure out how to adjust it but I can't find any information on it. The cable isn't broken, as I can see the cable move, it just doesn't seem to move enough to open the hood release. How I can fix/adjust it so it will work? Do I need to adjust it at the handle, or at the actual release under the hood?
View 12 Replies