My 99 ranger has just hit 111,000 miles. I'm getting a weird sound from the front right whenever I turn the truck slightly to the right. I don't hear it if it's leaning left. Is this likely the wheel bearing? I've heard these rangers are not best known for the quality of the wheel bearings.
View 14 RepliesThe truck just won't turn over makes a rrrgh rrrgh noice like it wants to start, I push the gas peddle to the floor and I should smell a lot of gas but don't!!! I added oil when it died at the store last night and it started up but the oil stick indicates oil is fine??? Pulled the diode out this morning put it back in the truck would not start just made that noise but turned it off and reseated the diode and it started??? These things may or may not have anything to do with the problem. Could it be electrical or oil pressure gauge sticking or something else that I could tell my mechanic and he could fix so I don't get stuck????
View 14 Replies2000 Ranger, see my sig.
Just had to swap out the pads on my truck yesterday. The pedal was pretty mushy and I was getting shaking in the steering wheel when the brakes got warm. Shaking wasn't all the time, only after they had been used quite a bit - say after city use and the brakes had to be applied suddenly. So I popped off the tires and swapped out the pads and replaced the brake fluid - flushed it.
On the driver side front, the pads barely had any real wear and the anti-rattle clip was all messed up. It was installed properly, but it looked like the pads had smashed into it. The rotor appeared to be warped, or at least out of round - but just barely. You could see it wobble slightly in one spot if you spun the hub with the caliper removed. The caliper itself was sticking slightly.
I didn't see any evidence of damage, the brakes flushed just fine although the fluid was incredibly dirty (because I haven't done it in a long while). On the passenger side front, the pads were worn down to the level I would have expected given the mileage. The wear was even.
My question ultimately is this - is the out of round hub the culprit here? Might there be something else going on like a caliper problem? Ultimately I plan on having the rotors surfaced - one of them certainly needs it and with new pads I might as well do it anyway.
My 2002 4.0L V6 Ranger, 4x4 overheated *slightly* this past weekend. I added some water and limped it home with a couple stops, trying not to let it get too hot. I since noticed there is oil in the coolant, so jumped to the first non mechanic's assumption the head gasket was bad. I have had (auto) tranny troubles with this truck in the past and started looking inside today and noticed some red fluid under the truck. I think the tranny fluid cools through the main radiator on this one, yes? If so, do I likely have a bad radiator, or is there another likely possibility?
The only wet areas I can find look like where the hard lines come into the right side (looking from the front) back of the rad. If we can determine that, would I need to replace the radiator, or is there any way to plug the tranny lines and run through a separate cooler? I think this also has a tranny, or oil cooler in front of the main radiator but not sure if that is correct, or what exactly that is. This is my daily driver work truck and will bring work to a stop until I can figure it out.
I had a friend do an alignment on my truck yesterday. Afterward, we tried to center the wheel the best we could in the shop. But when I drove it home I noticed that when going straight, the steering wheel is ever-so-slightly turned to the right. Is there and easy way to adjust this without me going back to the guys' shop and bugging him again? I know the alignment is dead nuts, but the wheel is just a tad off.
View 4 RepliesI recently acquired a B4000(for a steal!), had it almost a month now and im starting to notice a few problems, all driveline related (I think).
1. Have a "grinding/rubbing" noise in a LEFT turn only. It is a 4x4 and I haven't turned a bolt on it yet, save for very minor stuff. Since this particular model has some costly parts, I'm trying to prevent buying unnecessary parts! I have a set of 31 x 10.50 on it, and even though there is some minor tire rub, im 90% certain this is not the case.
2. Has a somewhat "hard" shift when going into O/D(I think), doesn't do this all the time, I wonder if problem #2 and #3 are related.
3. Appears to be about 1in slack in the rear driveline, wondering if it is the rearend, and specifically the spider gears or pinion?
4. Also seems to be just a LITTLE slack in the front left CV axel, is this something I should be worried about? the front right is good and tight, Tcase shifts like its suppose to.
03, 2.3 duratec, 163k, new timing chain, plugs (AP104), wires and intake. cleaned MAF, air filter, and ran two cans of sea foam through the intake and its still pinging. its driving me up the wall. truck runs perfect but seems to idle slightly higher and take longer to come down to idle after I got the timing chain and plugs/wires done. I've sprayed starting fluid around on top of the engine looking for vacuum leaks but found nothing. What should I try next?
View 14 RepliesWhen I make a left turn I have a horrible grinding noise. Only when I turn left and at any speed.
View 2 RepliesI purchased a new 2000 mazda b4000 2 weeks ago and the belt was squeaking and I knew I had to change the water pump so I replaced it and the squeaking didn't went away... I thought maybe my idler pulley bearing was worn out cause I could see it wobble back and fourth when the engine was running... Replaced it, still squeaking! Change my belt still squeaking! look further turns out my power steering pulley wobbles slightly. I'm thinking about trying a gator back belt and see if the squeaking goes away. Could it be dangerous to run the truck as it with a slight misalignment in the power steering pulley? or it'll be a must replacement asap?
View 3 RepliesThis rattle noise occurs when hitting just about any kind of bump. Sounds like coming from driver side. It sounds like something loose like a washer rattling against something metal. I recently have replaced the radius arm bushings, front springs, and shocks. The sway bar links and bushings look and feel ok. What it ended up being? I have never heard ball joints make such a noise but it wouldn't surprise me if they were in need of replacement.
View 10 RepliesI'm hearing a sort of faint rotating squeaking noise coming from the front of the engine; I can only assume that it's something with the belts. Nothing too pronounce cause I just notice it yesterday, anyway I was hoping I get another take on what this might be before I take it to the mechanic tomorrow.
View 12 RepliesI recently bought a 2006 Ranger with supposedly 110000 miles... I don't think I made a good deal... because I found the stabilizer end link in terrible shape which seems suspicious for this mileage in my personal opinion!? But this isn't the reason I am posting today... I have a serious breaking issue and I couldn't find explanation yet.
My ABS Light is on. When I slowly brake at low speed and when the brake is almost completely depressed... I hear a low humming sound, and the brake pedal seems to momentarily drop back just slightly. This also happens when I'm going down hill and breaking. For the most part, the car breaks, and it's only every 8th or 10th time braking that I experience this issue.
My guess is this is linked to the ABS... but I can't afford expensive service and need to resolve this on my own.
first off my truck is 2001 ford ranger 4x4 with an auto. transmission. when I'm driving around in 2wd, everything is fine...
when my 4wd high is on, and I'm starting from a deadstop my truck makes a weird "clunking" noise in the front end. If I'm stuck in mud or snow, and I give gas it keeps "clunking". where the problem comes from?
My truck jumps or runs roughly... I don't know how to describe it. It's like if someone dumped the clutch. It's a manual, it does it through all gears, so I don't think it's the transmission. I was thinking it might be the fuel pump, but I don't know how to diagnose it. I've got an 83 with the cologne v6. I think it's just got the engine driven fuel pump, no electric, but I'm not sure. Either way, I think it could either be the fuel pump or maybe a vacuum leak.
View 2 RepliesMy truck rattles when going up hills. The higher the rpm,the more it rattles. It sounds like a heat shield shaking. Also, when I accelearate on a flat road, I hear this very light knocking sound.
Motor has 190 000 km and is due for an oil change. Spark plugs and plug wires have been replaced. Engine sounds good when I rev it. No abnormal sounds. So, what would be my issue? Carbon build up?
1994 FORD RANGER stalls while driving - differant speeds ...differant miles ...no rhyme or reason to it - cranks right back up ...can even pop clutch and cut it back on. Already replaced Ignition Start Module - Dpes sensor - temp sensor - and scan shows all codes are clear and truck passes. We are clueless to whats causing this. 4 cyl 2.1
View 12 RepliesI have a 95 Ranger with the 2.3L and it is a five speed. I am having a starting issue. I have replaced the ignition switch, clutch position switch, starter relay and had the starter tested. The truck will not start with the key. I can jump across the relay and it starts fine but will not even click with the key.
View 3 RepliesI had my battery out for quite some time. When I put in a brand new battery my key was not recognized and my truck will not start.
View 3 RepliesAlthough my lil' truck (2006 Ranger XLT, 2WD,with 4-cyl / 5spd, and 115K miles) has been running just fine since I bought it about a year & 5K miles ago, I suspected it still had its original spark plugs and I figured I should change them before problems arrived.
As I suspected, the plugs that I took out looked to be original. I measured their gap and they all had excessive plug gaps - around 0.052" gap. I installed the four new AUTOLITE APP104 (double platinum) and checked their gap, and they were a bit tight at 0.042". My book says they should be at 0.044" gap. But I installed them at 0.042 anyway, figuring they'll burn wider in time.
One by one, I smeared a small bit of never-seize on the plug threads & at the plug-to-cyl head tapered edge. I smeared a dab of Dielectric Grease around at the top of the plug to ease the plug wire re-install and hopefully calm any possible arching. The plug wires came off the plugs easy enough and went back on just as easy.
I hit the key and the engine fired right up. It idled rough as expected. However, it continued to idle rough and if I raised the RPM level, it would respond, but still ran rough. It is throwing a 'Check Engine Light' on the dash cluster now - whereas it wasn't prior to the new plugs.
Last night I decided to see if I couldn't do something about my leaky carburetor in my 1983 ranger. It's a motorcraft 2150 carb. I took it all apart and followed a guide to clean it, then put it all back together and reinstalled it today. Unfortunately my truck won't idle, makes a whiny noise, and acts odd with the accelerator.
I've got a video posted here : 1983 Ranger Carb troubles - YouTube ....
I tried to explain this to a garage in January with no luck. When it is raining I hit my brakes and my truck jerks like whiplash. Softly hitting brakes doesn't do it, normally hitting them does it (only in the rain), I had some welding done after I went to the garage.... They fixed the front passenger side now it feels like it is under me and it is now doing it when I brake in reverse too... I bought it October 2012 and it was safety inspected until October 2014. Trying to decide if it is worth keeping. I want to keep it but when I go to a garage they see dollar signs. It only acts up when it's raining. And I had the welding done in January and it was fine, until I got new tires last week.
View 12 Replies