Ford Ranger / B-Series :: No Reverse Lights - Switch Location?
Aug 7, 2017
I've got a 2008 Ranger FX4, 4.0L with manual transmission. Recently I noticed that I have no reverse lights. I have to parallel park on busy streets from time to time, so this is a safety issue that I need to fix.
I checked the bulbs, both seem fine - would be unlikely that both bulbs would die simultaneously. I checked the fuse. Again unlikely unless the reverse lights were on their own independent circuit. 10A fuse looks fine too.
Last thing I can think of is a switch. I checked my Haynes Manual, there is no mention of it, which is odd, usually my manual is quite good. Where the switch is located? Any experience with swapping this out?
View 2 Replies
Advertisement
Apparently, top secret location of the oil pressure switch on the 1997 Ranger 4.0?
View 3 Replies
On my '96 ranger with an automatic the reverse lights only come on between park and reverse, but once put into reverse they go out. The gear selector on the dash reads right, when the needle is on"P"it's in park, "R" drops into reverse and so forth. Do I need to adjust the shifter cable on the side of the transmission? If so how do I do this (I kinda need step by step with removal and adjusting, I've already tried and couldn't get it off the bracket). It's starting to drive me nuts, I've searched on the web for hours with no luck. I've even posted on other sites with zero answers.
View 7 Replies
Since last summer my truck keeps blowing fuse 26 and then I have no reverse lights. If I replace the fust its ok for a bit but blows again the same day sometime. The book says its the fuse for revers and overdrive. The overdrive button on the tree shifter stops working too but the truck does not seem to be revving any higher so I think the overdrive itself is fine. I can't find the short but its got to be shorting somewhere...
View 14 Replies
Looking for an image of pvc valve location....2003 ranger 3.0......
View 2 Replies
Where the cabin air filter is located on my 97 Ranger. I purchased the truck used one year ago and would like to check or change if necessary.
View 2 Replies
Where the temp sensor for the rear view mirror is located. My truck is a 2011 Ranger with the 4.0 liter, AC, automatic and 4x4. I think it is somewhere by the headlights but not sure.
View 6 Replies
3.0 - Where is located ?
View 2 Replies
Where the modulater valve is on my A4LD tranny. I have a 93' ranger XLT extra cab 2wd with 4.0 engine. I have looked all over the tranny and thought it would be somewhere I could see it. I know I had one on my old full size Ford truck with C6.
View 7 Replies
Where is the location of the fill plug for a 93 Ranger transfer case? The damper is off and I see the drain plug. Is the fill plug behind the electric motor that shifts the case? I can see what may be a plug there that looks plastic with a very small hex head in the center of it. Is that it?
Also, my Haynes manual says to use Mercon ATF in the transfer case. I see where Valvoline has a Mercon equivalent. What do ATF brand people here recommend?
View 2 Replies
I have a 1987 Ford Ranger that only has high speed on the wipers. According to the Ford Shop Manual the probable cause is the interval windshield wiper governor, which is suppose to be mounted above the driver's side kick panel. The manual even shows a drawing of the governor and the location. Nothing is there in my truck. Where it is located and what it looks like?
View 14 Replies
So 85 ranger with 2.3l and A4ld. I can manually shift to get first and 2nd. When i look at the vaccume diagram it shows these 2 blocks on the tranny,one box is connected to the next with a vac line. The other box has 2 lines, one goes to the main vaccume block on the intake and the other T's into a small capped off canister and the egr. I can only find one place for a vac line and its on the pasgr side of the tranny... Where is the block that the egr line connects too located? Its not on the tranny as far as i can tell.
View 2 Replies
I have a 2000 Ranger with the 3.0. Was wondering where the fuel pressure regulator is located on it. I like pictures.
View 1 Replies
New owner of a used 2002 Ranger XLT 4x4 (with 59k miles) here (and new to this forum). Having problems with the oil pressure gauge not registering on cold starts (though it registers after the engine warms up).
I know this is nothing more than an idiot light since the gauge isn't really a gauge (inasmuch as it registers in the normal range at 7 psi and stays there unless the pressure goes away).
I've read that this is likely due to the oil pressure switch not functioning properly. I'd like to know where this switch is located on a 4.0 L V6. Other than this, the engine functions normally (though it sucks the gas).
View 6 Replies
I have a 2000 Ranger with the 3.0 in it. Trying to find where the fuel injection pressure damper is located. I was told it's on the fuel rail. Just making sure I'm looking at the right thing.
View 3 Replies
It looks like my door lock wire looms go under the hood but I haven't had any luck finding them. Install an alarm with negative 500Ma pulse to operate them ? I have relays but am also wondering if the truck has its own somewhere that I can piggyback onto. I know the colors are Pink with a yellow stripe and Pink with a light green stripe.
View 7 Replies
This morning the passenger side wiper on my 89 Ranger stopped working. I heard a clunk noise and it stopped but driver side still works. What should I check first? I'm guessing a shaft came off but don't know where it is located.
View 14 Replies
A buddy of mine has a 2003 Ford Ranger Edge V6 3.0L, he got the code P1450 the other day and asked me to look at it. Got all the info on what it could be but where ex actually is the EVAP canister and CV solenoid located? And what is the problem?
View 1 Replies
I have a 1999 ford ranger and I believe my Clutch safety starting switch is going out. Some times I push my clutch in and truck starts fine other times it will not turn over so I stomp clutch and then it starts. My question is, is there any way to bypass this switch?
View 5 Replies
In my 1999 Ranger, I can flip the air outlet switch to cause the air to exit either up, down, or straight out -- except that most of the time the air WILL NOT come straight out the dashboard ducts. I am assuming that there is some kind of diverter valve inside the dash that is intermittently working, but I do not know how to get to it. Do I remove the radio panel? If so, how? Or is there a way to get to it some other way, like from underneath or through the glove box? Does it just need a shot of WD-40 to free it up?
View 7 Replies
I have an 88 ranger 2.9 manual trans. The clutch safety switch wires melted (red with light blue) 2 come off the ignition, I traced the one to the clutch switch and replaced. My problem is my book says the other goes to " electronic shift control module", I can't find this module and I can't seem to chase wire as it gets lost in wire loom.
View 4 Replies
