So my sister has a 2000 Ranger 2.5L. I put in a new starter today for her today, and the second I re attach the battery terminal it turns over but wont fire.?
View 4 RepliesOne month ago. I am at a store and it won't start. Turns over for a second but wont fire up. Waited a while and it finally did. Took to auto parts place and we went over all that it might be. I checked the button on the passenger side and it was down as it should be. I replaced fuel fuse 48 in the box under hood. All was well for a week
3 weeks ago again wont start but this time it will turn over and over and over. Waited again and it cranked. Went back to auto place dude said maybe the ground to the computer. So I put a neg ground on it to the frame. Worked for a few days.
1 week ago Again cranks but wont fire. I take it to the ford house expecting expensive sex. They kept it for 2 days and it cranked all the time. They told me it had to not start so they could get a code. Check engine light has never come on. Even when it wont crank. I got truck and went to eat. And yes then it wont crank. Waited and had another marg and it finally cranked but you could smell gas like it was flooded. Took it home.
Today I took it down to auto place and tested fuel pressure. 60 psi no problems. grrrrrrr well maybe it ain't fuel pump. I have to have a truck I can rely on. I have football playoffs coming up and I travel a lot. It has a brand new interstate battery. I put Lucas gas treatment in tank. Dude at auto place said it would clear fuel line and lube fuel pump? It was 10 bucks for big bottle so I figured it couldn't hurt.
If its 10 at night and I am at a game shooting THEN Im sure it wont start.
My truck will fire while the starter is engaged ,but stalls when the key is in the run position. This is my plow truck and I don't want to go through the winter without it.
View 14 RepliesMy 2008 F150 5.4l SCrew wouldn't start this evening. The engine turns over and the starter engages, but it won't fire. Oddly enough the starter stays engaged after I take my hand off the ignition! I have to physically turn the key off for it to quit (didn't want to burn out the starter). The culprit may be the wet weather....it's been a lot milder today and we've had some freezing rain that turned to drizzle. My truck has only done this once before (last year I think). I eventually got it to start tho.
View 13 RepliesWhat might be going wrong with my 2003 Celica GT? The problem is that it infrequently is taking longer to start. The starter turns over the engine, but it does not fire. It continues for a considerably longer time to crank the engine, then finally it fires and starts. Could it be that the fuel pump is beginning to fail?
View 3 RepliesMy father in law has a 98 4wd, 4.0L that cranks but doesn't fire. We pulled a plug to check for spark....no spark. Possibly coil pack, or crank position sensor?
View 5 RepliesI have a 1995 ranger with a 4.0 it cranks just fine wont fire has alot of fuel spark it will crank and crack then it stop and acts like it is going to fire up and stops cranking... This thing has 253k on it...
View 4 RepliesI have a 1995 Ford Ranger, manual shift. It always starts when cold, but sometimes -- very sporadic -- it will not start after I've gone somewhere. This has happened maybe 8 times over the past 18 months or so. Always, after sitting a while, it starts right up as though nothing happened. Several months ago I left it with a mechanic for an entire week, but he could never get it to act up. Of course.
In browsing through these discussions, I've seen the "starter/clutch interlock switch" mentioned. Here is my question, though. Would the starter still crank if that was the problem? or does that switch stop the starter from engaging?
When mine acts up, the starter cranks, the engine turns over ... it just acts like it's not getting fuel. Is that a starter/clutch interlock switch issue? Or something else?
I have a 2005 ford ranger, 4.0 auto, 4x4, 60psi fuel presser, has spark and injector pulse, will try to start if you hold the throttle a little over 3/4 the way down, but will not fire on starting fluid.
View 3 RepliesI just finished putting in aftermarket A/C in the 2004 Ranger my dad gave my son. It's a 2.3L, STD transmission. It was running GREAT before the project started. I installed new battery as part of the project. When I started it back up it ran for 2 or 3 seconds then died. I now cranks, but does not fire at all.
I have tried one of the key reprogramming sequences (turn key to "ON" 8 times) with no success. Would it crank at all if it were a key security issue? Is there anything I need to reset anywhere else, like in the air intake system?
It's either not getting spark or not getting air. The fact that it ran for a couple of seconds has me confused. Would it run at ALL if there was a key security problem?
I had to remove and reinstall the air filter housing and ducting. Is there anything else I need to do to with the air intake system?
2004 ford ranger 3.0 ... So here it goes I am pretty mechanically incline for the most part i would say until this last week i got a rod knock. So i replaced all my push rods put everything back together and now my car cranks but just wont start up where did i go wrong. I cant afford to get another truck i just want my baby back up and running ...
View 14 Replies My buddy's 1998 4.0L Ranger caught fire from the dreaded brake switch shorting on the master cylinder. In his defense, he's only owned the truck less than a week and had no clue of the recall. The damage is mainly to the wire harnesses on the driver's side.
Rebuild the wiring. What other years of the Rangers I can pull the wiring harnesses from? Or if the 3.0 harness will work?
I have a 2002 Ford Ranger, and it wont start at all. Ive replaced the starter, had the battery checked. Not the battery, took starter out, had it checked too, its not the starter either. Someone said it maybe a fuse? This is totally frustrating, and I need to get it figured and fixed asap. Its been going on for weeks., I had it fixed and then it just stopped. It wont even take a jump anymore.
View 4 RepliesI have a 95 Ford Ranger 2.3L with a five speed. I recently had a starting issue were I parked the truck, went into a store came back out and the truck wouldn't start. Figured it was the solenoid as I couldn't jump across it to get the truck to start. Replaced the solenoid. Still no go. Found a fuse in the starting circuit blown. Replaced the fuse and got it started and drove home. Next morning, I go to leave for work and the truck would not start. Got a ride to work came home and checked it over and found the starter locked up. I replaced the starter. Truck started for a few days and now I am having problems again.
Here is the problem I am having now. Starter is good. Proved that as I can start the truck by jumping across the starter relay. Checked the solenoid with a voltmeter and it is doing what it is supposed to do when the truck starts normal. Here is where I am scratching my head. I can start the truck sometimes and it starts just fine. Next time I try to start it, the fuse will blow.
Replace the fuse and it might work for a couple of starts and then the fuse will blow again. I jumped pass the fuse with a piece of wire for diagnostic purposes. Out of 20 starts, it only started normally 4 or 5 times. I have checked every wire I can see under the dash and have not found any obvious issues. I am at a point where I am so frustrated that I just want to push this 400k mile truck into the back forty and put it out of its misery like a lame horse.
I have a 2002 Ford Ranger with a 3.0L engine that is having some issues with starting, here is what is happening.
Every so so often when the key is turned to start there is no movement from the starter motor. The battery is fine and all of the dash lights stay on while the engine is not starting. I have replaced the starter with a remanufactured model (possibly a mistake), and also replaced the clutch interlock switch.
I have attempted to change the ignition switch but the replacement I received did not even try to turn the starter (after many tries), like possibly it was faulty out of the box. I am currently using the OEM ignition switch as it will at least turn the starter eventually. I just worry that this problem will develop further at the wrong time.
Its and 03 ranger with a 4.0 auto and it grinds after starting and it doesn't always start smoothly, like it hops around till it finally starts, kind of like the starter wont disengage. Do I start with a new starter or is more than likely a flexplate issue? I hope its just a starter.
YouTube video : 2012-02-16_15-35-45_211 - YouTube
2nd problem is it hesitates a second or so before it goes into gear and clicks in hard, kind of like when you are low on oil, but its not low on oil. It also shifts hard. When I got it the column bolts were loose so the shifter was floppy, I am wondering is someone tried to fix it the wrong way. Also now its pretty stiff to move the shifter selector.
Also what tranny is in it, it may be some sort of heavy duty unit, it was an x electrical municipality vehicle, it appears to have an 8.8 and heavy duty rear springs. Door tag reads axle rd, tr D, and spr 2c...
My 1991 ranger with a 4.0 turns over but will not start. It acted like it ran out of gas put again seems to do ok then it did same thing it sat over night then would not start so I thought I would put some gas in the intake so it starts ran real rough but smoothed after a few minutes ran fine after that next morning same thing no start did same put gas in intake at first no start just turned over didn't even try let it sit for awhile then tried again it fires up ran rough but ran now I get nothing just turns over pulled codes 22and 122 replaced both had ignition mod checked its good new coil pack no change so at this point i hear fuel pump kick on fuel getting to fuel bar but seems a bit week on pressure going to get pressure gauge and see what it says but in the meantime I am loosing my mind...
View 9 RepliesWell it all started when I was having starter issues my starter died and my solenoid was just clicking and after time there was no power at all to anything in the truck i have replaced the solenoid and starter and check battery and cleaned post and terminals. I am going to replace my negative cable as it was pretty bad but if this still does not work, so what to look for. The truck is an 87 ford ranger 4x4 5 speed with a 2.9....
View 9 RepliesBut here's too my question. I recently bought a 2wd Ford ranger 2.9 automatic. Bought not running. They said it wouldn't turn over that there was something wrong with the starter. I figured it was the neutral safety switch turned out it was there's a wire broke on it. I can get in there touch the wires together and it'll turn over. But I can't fix it because the shifting linkage is In the way. I'm wondering how too take it off. I've never worked on one before. And I don't wanna mess up my gears.
View 1 RepliesMy son's Ranger wouldn't start today, turns over fine, added gas to make sure it wasn't out still no hit.
Other than fuel pump (he said he couldn't hear it) what things should he check? I'll check back in the morning.
1994 Ranger 2.3 4 Speed ....
My Ranger was running great when suddenly on the highway it just died. I towed it to local nationally known brake/ muffler shop where a good friend is the manager. He narrowed it down (guessed in my opinion) to no spark and no fuel. He thinks it could be the crank sensor, the fuel pump or the ignition module. Is there any way to pinpoint the problem without replacing parts? It will sometimes start and run for about 2 seconds before shutting off. It will not repeat this unless it sits for a day or two. I am not sure if there are different 2.3 engines available but mine is fuel injection and has two sets of spark plugs and wires.
View 9 Replies