Ford Ranger / B-Series :: Missing When Started And CEL Came On
Aug 9, 2014
I have a 98 Ranger with a 3.0 (5 speed) that has 254,000 miles on it. I drove it to town this morning (8 miles) and it ran normally. I stopped for just a few minutes at a house and when I re-started the truck, it was missing very bad and the CEL came on. It wouldn't haul itself in anything higher than 3rd gear. I decided to try to make it back home. I drove it less than two miles and it cleared up and started running perfect again. I came home anyway and read the code with my scan tool.
It said that I had a miss fire on cylinder #5. I erased the codes and shut the CEL out and its been running perfectly ever since. (I have put about 150 miles on it so far) If it does it again, I will start by replacing the plug wires. I have already done that but its been a long time ago. The plugs have been replaced twice as well. I was wondering if it could be something other than electrical like a dirty injector or maybe the compression rings lined up and it momentarily lost compression.
View 14 Replies
Advertisement
The other day I was driving down the road on a long, flat section and all of a sudden my truck started missing out of the blue. Ever since it started missing it hasn't stopped. The truck is an '89 Ranger, 2.3l, 5 spd. The plugs and wires were replaced last year along with the timing belt and fuel pump. It has been running great since then until now. I thought maybe it might be a clogged fuel filter so I replaced that but it didn't work. Also, it doesn't miss all the time. It doesn't miss when its idling or if you are going down the road while it is missing and slowly release the gas pedal it reaches a point while you are letting the pedal up where it will even out. It definitely seems like it is an "under load missing" scenario. Also, the Check Engine Light is not on. Where should I start looking?
View 4 Replies
I have a 2001 ranger 2wd with a 2.3. It has a miss when acceleration. There is no check engine light. I have changed: fuel filter. Plugs, wires, crank position. Sensor, cleaned mass air flow sensor. Ran 2 bottles of injector cleaner in it. Still missing???? It runs and idles great. Just has a miss in the lower RPM's 1000-2000 then goes away. I really don't wanna take it to a shop. What do you all think??
View 11 Replies
85 ranger 2.3 fuel injected misses at high acceleration. Fairly new plugs and wires, just replaced the timing belt, pretty new fuel pump in tank, new fuel pressure regulator and pcv. It idles well, starts up and drives pretty well until you get it in 4th and really bog it down. Could be timing issues but I'm pretty sure I did everything right when I put the belt in. What it could be? I know when the tank fuel pump went out, it did something similar for a while...
View 9 Replies
I've got a 1988 2wd Ranger with a 2.9l v6. I just recently got it running. It has been setting for awhile. I replaced fuel tank, both pumps, fuel filter, Plugs, Wires, Cap, Rotor, TPS. It ran great for about 100 miles. Then yesterday on my way to work about 4 miles down the road it started to miss/stumble especially at about 55mph while in overdrive. When I got home I pulled the codes and I got KOEO 22 Map sensor signal out of voltage(engine off), 53 TPS signal voltage to high, 95 Thermactor Air System Problem, or Fuel Pump Monitor signal, indicates circuit problem.
KOER I got 21 ECT sensor signal voltage out of range or loss of signal during normal operation or Crank Sensor problem, doesn't have a crank sensor I believe. But I did change the ECT sensor and it still stumbles and seems like it misses. Noticed it is sluggish getting up to speed kinda surges and bogs. Im at a loss it isn't showing any more codes. Checked all plug wire connections and made sure everything was making connection. The only other thing I can think of is that the ignition module on back of distributor is going bad. Not advancing the time correctly.
View 14 Replies
I've a 1994 Ranger XLT 4.0L with a missing fuse panel cover. I'm trying to get the horn to work and we've traced the problem to a missing fuse. Unfortunately, there are 3 empty fuse slots and no info on their rating or use. Where I can get the proper info. Truck was a salvage, no ops manuals, and sloppy work putting it together.
View 14 Replies
4.0. I'm having what feels Like a Miss on Light throttle/cruise. Once warmed up it's fine. Idle is fine too. There is No CEL/Codes.
View 14 Replies
I live in Kansas and was home in Georgia for the last 2 weeks. The truck drove great there after a fuel up started missing and surging at 50 to 70 thought it might have been bad fuel. waited till it was low added Lucas fuel treatment and premium gas still was doing it. no check engine light. went to Advance and fuse for light was blown they checked and was getting mass air flow code. unplugged it and seemed to be better, not perfect but better. plugged it back in and went to do it again. Changed mass air flow night before the drive back to Kansas. Ran well from Savannah to north Georgia then started doing it again the rest of the way home. Going to have advance check code again.
View 12 Replies
1998 4.0 ... She only misses about 30 seconds during stone cold startup. I figure it's probably the plug thats hardest to reach ? Isn't that the way it always is? From the hood I can see only one spark plug, so I figure I'll do all the plugs. Is there any right or wrong approach to the plugs? I did the thermostat today, but this plug job looks like it's gonna be a bitch. Time for some skinned knuckles Next is the right side O2 sensor, that looks like fun too. But I gotta say, this little truck is sweet. Great visibility and easy to park in the city. I really like her. She's a keeper. She needs some new sway bar bushings too, but no surprise with 127 K on the clock.
View 5 Replies
My 2000 Ranger standard 4.0 4x4, started spitting and sputtering the other morning just when i was gone up hills then it would quit doing it. The other evening it got to where it don't idle, missing very bad, and wouldn't even pull itself up a slight grade, and the wife said there was flames and sparks coming out the exhaust. Now it wont even try to start, it just turns over. I put a different coil pack, wires, and plugs, and still nothing. I pulled the gas line off the frame fuel filter and its shooting gas out, and I got gas to the check port on top of the engine.
View 5 Replies
1996 4x4, manual trans. Wants to kick out of first, and when shifting into 3rd I have no gear. Doesnt grind, just goes in as though it were neutral.
View 4 Replies
2001 M B3000 v6 my sons truck w 122k. He is overseas and I took it to deliver a CB750 bike to my brother in law... 4oo miles away from my place.
In the middle of nowhere TX it developed a bad miss or knock, almost a shudder in the 2 to 3 k rpm range. Idles ok just below 1k runs fine at 70 mph as long as the rpm is near or over 3k.
Not sure I want to turn around and drive back the 400 with it running like crap. I will take it to Autozone and pull codes tomorrow a.m. but what should I expect?
View 9 Replies
2002 ranger edge 3.0 5spd. Truck idles perfect, but when you get rolling and higer rpms feels like the engine is missing. loos of power and shakes. I replaced the usual, plugs and wire's, seemed to work for a bit but came back. I cannot get any info on the scanner and have checked all the fuses. I am thinking coil pack but don't understand why it idles perfect and only misses under acceleration. No check engine light on.
View 5 Replies
2002 ranger edge 3.0 5spd. Truck idles perfect, but when you get rolling and higher rpms feels like the engine is missing. loos of power and shakes. I replaced the usual, plugs and wire's, seemed to work for a bit but came back. I cannot get any info on the scanner and have checked all the fuses. I am thinking coil pack but don't understand why it idles perfect and only misses under acceleration. No check engine light on.
View 14 Replies
2003 Ranger (4.0 L-2wd)...
Codes - random misfire and cylinder banks 1, 2, 3, reads out lean fuel
Will be checking out injectors and rail pressure, however, trouble shooting in general for this issue.
View 7 Replies
I have a 96' ranger that has been missing quite regularly. The vehicle has over 200,000 miles on it, but has been taken care of regularly by me since 75,000.
Problem: When I start the vehicle, the engine takes a little bit to find the idle. It spits and fumbles around some until it finds a somewhat rough idle. Often, when I first start driving in the morning, the vehicle really jumps around due to misfiring. Even after running smoothly for awhile, the vehicle with sporadically misfire with no rhyme or reason. This is particularly true when climbing a grade. When sitting at a red light and idleing in gear, you can definitely feel the truck shaking from side to side. Also, when idling in gear, the battery gauge on the dash fluctuates, but when the vehicle is in park the battery gauge doesn't fluctuate...it just idles a little rough.
I had the Ranger to a garage and had them check the battery and alternator connections and ground to try and figure out what is making the battery gauge fluctuate...alternator and battery checked out...no diagnosis for fluctuation.
I replaced all plugs and wires and also checked the coil pack. One of the coils (#6) had some build-up in the top. I cleaned it out and replaced all the plug wires and everything snapped in place and fit fine.
The garage did tell me that an error code came up with the EGR valve and or sensor. They didn't seem to concerned about it. Do the EGR valve could be the cause of all the stuttering and misfiring going on with the ranger? I really don't know where else to look. Maybe replace the coil pack?
View 3 Replies
So Im working on a 1998 mazda b4000, frost plug blew out going down the highway changed the engine because it got cooked pretty bad. The wrecker engine I got for what ever reason will only run good if the driver side of coil pack is done 5,6,4 any other order truck wont run at all. Misses enough to shake the truck at around 80 km/hr otherwise its pretty good. Also the engine I got came factory with no egr.... no provisions nothing. exhaust manifold capped off, seemed kinda odd.
View 5 Replies
Today while driving I noticed a knocking when turning right or going over bumps in the road. I finally got to look under the truck and noticed that I'm missing the nut on the top side of the front stabilizer bar link bolt assembly on the passenger side.
It's a '99 Ranger XLT 4x4. Is this unsafe to drive? Is there a bushing on the top?
View 3 Replies
Was fixing leaking water temp sensor today and noticed the nipple under oil fill cap didn't have hose on it. After further investigation I found open spot on air intake hose with nothing in it. Both places seem to have vacuum, what goes here. BTW it is a 1999 Ranger ext cab with 3.0 flex engine and auto trans. Will try to get picture n post also...
View 8 Replies
I have a 1998 ranger 4.0 and about a year after getting it the belt started to squeak so far if have replaced the belt, replaced the tensioner, and cleaned and wire brushed all the pulleys to remove glazing. And it still squeaks and its annoying and kinda embarrassing...
View 4 Replies
I have a 99 ranger with 170000 miles and the front end recently started squeaking. its coming from the driver side but I can't pinpoint it.
View 5 Replies
