Ford Ranger / B-Series :: Installed All Lights But Front Signal Won't Work With Headlights On?
Jan 8, 2017
Problem with 1157 LED bulbs . I install all 4 light bulbs the tail lights and front turn signal lights the problem is all lights work with the signal lights. but when I turn the head lights the front signal lights don't work. Also the turn signal lights on my dash board both light come on
One more thing if I install the regular 1157 on the front . the LED lights on the back work fine and the from work fine . looks like the front don't like the LED bulbs. I have 87 ranger cab and half or extended cab. v6 2.9
View 6 Replies
Advertisement
My brake lights will not work but all other lights do, bulbs and fuse have been replaced.
View 2 Replies
1999 ford ranger 2X4 manual trans. My back up lights work sometimes and sometimes not.
View 1 Replies
i have an 89 ford ranger custom and my driver side tail light works just fine but my passenger doesnt work when i mash the brake the passenger side brake light wont come on. the parking lights work, turn signals, and hazards work but the brake light. ive checked the wires and replaced the socket and still the same problem so either theres something in the wires that im missing or i dont know what else. any hints?
View 7 Replies
My interior right turn signal light wont come on. The right exterior bulbs work fine. I swapped the bulb with a new one and it still doesnt come on. Could the socket be bad? Should I have sprayed the cluster bulb socket with contact cleaner?
View 4 Replies
97 ranger 2.3l 5spd ... I keep getting p0500 code. the speedometer and odometer work fine. I understand they get they're reading from the OSS on the transmission. Now I also have the vss in the axle housing which I believe is what gives the ultimate speed reading to the pcm that way there is no need to ever adjust for axle ratio.
When using the torque app with my obd reader my OBD MPH guage does nothing until I get to about 55 then it bounces around randomly between 20 and 55 and once I hit 60 mph it reads correctly. I have tried 3 different vss sensors checked wire continuity from sensor to firewall examined the teeth/sprocket that gives the vss it's reading and it all checks out...
My questions are:
- What volts or ohms are supposed to come out of the plug end so I can test if the signal to the sensor is working
- Looking for wiring schematics for this sensor to pcm...my schematic only has the oss.
View 6 Replies
My backup lights only work when I have one bulb or the other installed but not both. The other 4 mini lights in the same circuit on the trunk work. The backup lights do not work at all when the headlights are on. Could it be the backup light relay and where is that located? I checked wiring on the trunk and multiple bulbs.
View 5 Replies
I have a 2003 V10 Excursion with an electrical problem. The right turn, right brake and right hazard light do not work but the flasher makes the clicking noise. When the right turn signal is on, the right front turn signal light works but is at double speed. The right rear light does not work. Same when brake and hazard are applied.
I checked the bulb socket with a multi meter and have no current. I also checked my trailer plug and have all functions work. Fuses were checked also for the brake circuit and were all ok.
View 4 Replies
I have a 1988 ford ranger and my headlights won't turn on all my fuses are fine but no headlights! All the other lights work fine blinkers, parking, brake ,and tail lights! What do I need to look for????
View 14 Replies
I have a 2000 ranger and the right low beam went out, we changed the bulb to no avil. I thought it might be the light switch so we changed it also ,nothing!! We have checked the only ground, I can find for the lights (on the driver side under the fuse box under the hood). This problem has me stumped . Another problem that may or may not be related is the cargo light does not work either...
View 8 Replies
The headlights on my ford ranger 1994 won't come off. All fuses are good and wondering the next step?
View 9 Replies
My front left turn signal won't work, the signal on my dash board doesn't work, and the signal in the rear blinks rapidly. but the whole right side is fine. this is aggravating, I have changed the lightbulb in the front and nothing happened. It still doesn't work.
View 5 Replies
99 Ranger XLT 4.0 4WD Automatic. With the turn signal blinking and I depress the brake the turn signal stops blinking until I release the brake. Where to start.
View 2 Replies
Just got home from work with my 2009 ford ranger XL 2.3 and it was running fine, went back out 10 minutes later and it would not start. No clicking noise from the solenoid or anything. Tested the battery (12.8volts). checked all the cables, checked all my fuses and everything is good.
Then noticed I have no power to my headlights, brake lights, or instrument panel. The only power I get is to the horn and the interior light. When I try to turn my headlights on or turn the key to different positions the "smart junction box" at the passenger side kick panel starts clicking. (there are no relays on this thing)
I decided to check the battery when the key is in the start position and the voltage dropped to 5 volts. Power is going somewhere but I am completely lost here.
View 2 Replies
The headlights on my 94' 4x4 have been kind of cloudy looking since I bought it two years ago. It's not condensation on the inside, the glass just looks like it has something on it. Is this a common problem?
View 10 Replies
I recently purchased my first car/jetta. When i switch the knob to turn on the instrument lights on my 2000 jetta the headlights don't come on. But when i turn the knob off the auto headlights turn on. Any insight on this? when i first got the car everything was working fine. It only started to happen after I replaced the radiator.
View 6 Replies
Toyota corolla 2013 automatic gear reverse lights don't work after I installed new stereo it's my fault i shorted 12v positive backup (reverse) light trigger camera stereo v12+ cable to ground while backup (gear R) in place. As a result reserve lights don't work beside gear indicator doesn't show on main screen. I can drive without problem but problem still intact.
I checked all fuses and they are all okay I need to identify problem or possible repair too I only find 2 fuses behind glove box i think they call "instrument panel" there are bunch of cable and underneath of cables there is only 2 rectangle shape fuses I could not see anything else, the other fuse box is in engine compartment i thoroughly tested each small fuses they are all okay is there anything else i forgot to check ?
I attached also instrument panel screen shot ....
View 1 Replies
The right turn signal on my 1998 Ford Explorer recently stopped working. The flasher was making a horrible buzzing sound when I tried to signal right, but worked fine signaling left.
I just replaced the flasher, which has cleared up the buzzing noise when trying to signal right. The flasher clicks like it's supposed to, but the lights still do not flash.
Here's a summary of the current symptoms:
-Hazard lights work fineFlasher clicks; interior indicators flash; exterior lights flash
-Left right signal indicator works fineFlasher clicks; interior indicators flash; exterior lights flash
-Right turn signal does not work
-Flasher clicks
-Interior indicator stash off; exterior lights stay off
What to check next???
View 4 Replies
All my guages move (needle moves to the right) once I turn on my head lights. Indicating higher egine temp and higer oil pressure. What cause be causing this?
View 4 Replies
Any schematic of the vacuum lines for a 99 Ranger with the 2.5 motor? I don't mean the general overview decal under the hood, but rather one that specifically includes the HVAC lines. I have two problems... one being that I have no MAX A/C (recirc does not work) and the other being that the vac line is busted off the heater core isolation valve and I can't find the other end of it (the end that supplies vacuum to open the valve).
View 3 Replies
So with 172,000 miles my truck has started a new trick. When I turn on the turn signals theyll flash or interrupt normally for a few times then stop. After I turn the signal lever off and back on again they start to flash again only to stop after several times. This happens to both the left and right hand sides. The emergency flashers seem to work alright. Is this a function of the indicator flasher SF631? If so, were exactly is it located?
View 5 Replies
