Ford Ranger / B-Series :: How To Change Front Rotors An Auto 4X4 Hub
Mar 12, 2012
Looking for a good write to change the front rotor (BIG CRACKS IN IT) on a 97 auto locking 4X4 hubs? Any special tools etc...?
View 7 Replies
Mar 12, 2012
Advertisement
Ford Ranger / B-Series :: Front Disk Pulsing - Brake Rotors?
My front disks are pulsing & the thickness is near minimum, so I guess I'll have to replace them soon. Is any particular brand better than others?
These stock ones are made by Bosch and I'm not impressed with their lack of resistance to warpage. I see "Drilled and Slotted" available at Rockauto. What's your experience? Are they any good?
Impala - Chevrolet :: Wheels Rubbing / Thumping Sound From Front - Couldn't Change Rotors?
My 79 year old father put fuel additive in his 2010 Chevy Impala. Don't ask me how much, or for how long... The Check Engine light came on. I never got a clear answer from him on what his mechanic said about it. Five to Ten fill ups later the Check Engine light went out on its own. Engine seems fine. Could this have caused damage to the engine or emissions controls? Would a computer diagnostic from a mechanic pinpoint any problems? Would you recommend a computer diagnostic be performed?
View 6 RepliesFord Ranger / B-Series :: CEL On After Oil Change?
I just changed my Oil, added a FRAM filter and bought some good Quakerstate High Mileage and my truck runs good. However, I noticed that my Check Oil light is constantly on. I also recently changed my Oil Sender, and I wonder if that has got something to do with it.
View 3 RepliesFord Ranger / B-Series :: 1998 2.5 Auto - Stumbling On Takeoff
I've been through this same scenario quite a few times before but I cannot narrow it down to the exact problem. I've got this 1998 Ranger that's maintained well, tune-ups, oil changes, and everything else maintenance wise. The past few months randomly driving anywhere from 200-300 miles every once and awhile it would hesitate taking off from a stop or accelerating after letting off the gas. It would throw up a P0171 code so I thought the fuel pump was bad. So I replaced with a new fuel pump assembly. That worked, fuel pressure is now within specs. 65-69psi. Still every 200-300 miles it would throw up a P0171 code, then a few weeks ago it kept coming up more frequently.
I found out it was a broken vacuum hose from the purge valve to the intake manifold tube so I replaced it. Now it doesn't come on anymore. But before I noticed that hose I assumed the mass air flow sensor was bad so I cleaned it with CRC Mass Air Flow cleaner. Since that time it's gotten worse and now stumbles and hesitates every time you stop and takeoff. Sometimes it even chokes the motor out with the a/c on and you come to a stop. I knew the ignition coil also causes the same issues so I checked them. The front coil pack had a burned electrode leading to number 4 cylinder intake side. I replaced the coil cleaned that end of the wire and it still is stumbling and hesitating. I tried the trick of unplugging the mass air flow sensor and driving to see if it was better. No change at all.
After I replaced the coil a few minutes ago I test drove it and stopped and then turned a corner and gave it full throttle with a/c on and it actually shut off. But still there is no check engine light and no codes present. What's going on? I looked at the back coil and didn't see any corroded terminals. It started happening all the time upon takeoff right after I cleaned the mass air flow. But when I unplugged the sensor and drove it around nothing changed at all. Is there something else to check? I had the timing belt changed last week and had the shop check to see if timing is good and they said it was right on. It still drive good you just have to tap the gas twice when you take off to overcome the stumbling.
Ford Ranger / B-Series :: 2001 - Auto Trans Won't Drive / Reverse?
Daughter driving truck truck quits moving, I get there no drive and no reverse, has low and 2nd manually.
drive truck home, flush trans and cooler, road test all ok. this was 3 weeks ago.
This morning did it to here again, no drive and no reverse, she drove it home using manual low and 2nd.
I get in and when put into drive it feels like it tries but doesn't go all in, same with reverse. pulled it into low and vola I now have drive and reverse again
I'm thinking a we may have a bad or going bad shift solenoid. What I need to know is, is any of the solenoid valves on when in reverse are they the same as when in drive?
Ford Ranger / B-Series :: 2006 - Way To Change Coolant?
I looked for any tips on changing the coolant in my '06 2.3L Ranger but found nada. How to best / easiest way to drain the coolant from this little rig? Is there any need to worry about bleeding any captured air in the system once I go to refill the system?
View 11 RepliesFord Ranger / B-Series :: 2003 3.0 2WD Auto - Fuel Pump Wiring Diagram?
I'm working on a truck for a friend's mother and all of the tests that I've done point to the fuel pump. However, to make sure the pump is getting voltage past the large connector block under the cab, I would like to do a pin-out test before I pull the tank (or the bed). The pump will not run/prime in KOEO test, the relay is good, as are all of the fuses and the inertia switch.
Looking for a wiring diagram handy for this purpose? I've look all over this forum and searched quite extensively and I haven't found one for this year. Since it isn't my truck, I don't feel like purchasing a manual. I'm working on a 2003 3.0 2WD Auto.
If a wiring diagram isn't available, what colors are the wires going to the fuel pump? That way I can at least test the ground and the positive.
Ford Ranger / B-Series :: 1998 4x2 2.5L Auto - Whistling Noise Coming From Rear Only Sometimes
My Ranger has 296,000 miles on it. Most everything has been replaced except the u-joints. It's a 2wd 2.5L with an automatic. The motor was replaced at 228,000 with a used motor with 52,000 miles. The transmission has about 60,000 miles on it. All the bearings in the rear end were replaced about 20,000 miles ago. It has the most annoying whistling noise coming from the rear only sometimes. I don't know if it's the brakes being misadjusted or a bearing with a burr in it. It happens at random times but it's such a high pitched whistling you know everyone on the road can hear it too. There is also a driveline vibration, very minor though when over 60. However, I've had the drums checked and even had the wheels balanced many times. My friend said the ujoint grease could be dried up, but the whistling noise only happens at random, the virbation is anytime you're at highway speeds. It's not a violent vibration just enough to tell that it's not a brand new truck anymore. What it could be?
View 2 RepliesFord Ranger / B-Series :: 2001 Edge 4.0 5 Speed Auto - Noise While Accelerating
MY 2001 Edge 4.0 5 speed auto has a noise while accelerating. It happens only when truck is first run and disappears after warming up after a few miles. It just turned 1500 miles. Can't figure out if it is from trans or possibly a speedo cable. It goes to the dealer next week.
View 6 RepliesFord Ranger / B-Series :: 1996 - When To Change The Timing Belt On A 2.3L
What is the recommended interval for the timing belt change? I have a '96 B2300 with ~85K on it and he original timing belt. I wanted to change the serpentine belt and my mechanic said he'll take a look at the timing belt. It's not cracked or anything but he says that after 8 years it should be changed.
View 14 RepliesFord Ranger / B-Series :: Change Shifting Points - Shift Into 5th At 45 - 50 Instead Of 55?
I have a 2002 3.0 with the 5R44E. I don't like how late it shifts into 5th gear. Is there a way to make it shift into 5th at 45-50 instead of 55? I feel like I have to let off the gas half of the time to make it shift and I don't have a heavy foot. If anything, driving with a light foot seems to make it shift into 5th later.
View 8 RepliesFord Ranger / B-Series :: 1986 2WD Not Running - Shift Linkage In Way To Change Starter?
But here's too my question. I recently bought a 2wd Ford ranger 2.9 automatic. Bought not running. They said it wouldn't turn over that there was something wrong with the starter. I figured it was the neutral safety switch turned out it was there's a wire broke on it. I can get in there touch the wires together and it'll turn over. But I can't fix it because the shifting linkage is In the way. I'm wondering how too take it off. I've never worked on one before. And I don't wanna mess up my gears.
View 1 RepliesFord Ranger / B-Series :: 2000 - No Change In Idle When Pull The Injector Plug
Its a 2000 flex fuel 3.0... Its not the actual injector. I think its wiring or computer. No change in idle when I pull the injector plug. But I think I can feel the injector opening and closing. Compared to nearby injector diagnostic light flashes less brightly. but that's pretty hard to quantify
When I pull the plug on another injector it idles about the same but I can tell it surge up and down as I disconnect and reconnect it. Fuel injectors were backflushed and swapped same problem cylinder. Where do I go from here just take apart the loom and look for abraded wires? Its the number one cylinder, passenger front.
Ford Ranger / B-Series :: Replaced Front Brakes Now ABS Goes On A Lot
I had to replace the tie rods in my mazda b2300 and the mechanic also replaced the brake pads.
Now when I drive, I can hear the pump for the brake fluid going on and off when I'm not even using the brakes and the ABS goes on a lot too.
He tried resetting the computer by unplugging the battery for a bit but it's still doing it.
Ford Ranger / B-Series :: 1991 - Front Hub Comes Off With Wheel?
I recently bought a 91 Ranger 4wd for my son. The guy I bought it from put new manual lock outs on it. every time I take the tire off on either side the hub comes with it! Is there a clip or retainer missing? If so what and where can I get one?
View 4 RepliesFord Ranger / B-Series :: Adding Oil In Front Differential?
Thought I would try and fill up the front. Diff well not as easy as the rear diff. They make a special hose or some thing. To put in the bottle so u can get some Gear oil in ?
View 3 RepliesFord Ranger / B-Series :: 1986 - How To Disable Front Differential
My front diff is busted, and I mean bad.. I can barely even run the truck 5mph, and it's very loud. The diff casing is even busted. I want to just disable it to drive in 2wd. What's the easiest way to do it? It won't disable using the push button control.
Can I just remove all the locking stuff in the front wheels, so there's nothing for the axles to grab on, and manually turn the solenoid at the transfer case to shut off the front wheel axle?
Ford Ranger / B-Series :: 2001 - Oil Pan Gasket Sticking Out In The Front
My son and I were doing a transmission flush and while we had it on the lift, I noticed the oil pan gasket was sticking out in the front quite a ways. I assume its time for a new one. Is there anything I need to know having never dropped the pan on this truck? Is this a common issue?
View 14 RepliesFord Ranger / B-Series :: 2006 - Vibration Above 55+ From Passenger Front?
In my 2006 Ranger XLT, 4.0L V6, 2WD Manual; I am getting vibration from what appears to be the passenger front. I have so far replaced the front wheel bearings (both sides), replaced front shocks and checked rear shocks, rotated tires (to see if it changed) and had front tires balanced. I've also had a friend follow me on the freeway and check the wheel to see if is bouncing, wheel appears to be glued to the road. I have done all the front suspension checks I can and find no indications it is the lower ball joints or tie-rod ends.
This vibration is very in consistant, in different lanes it is better/worse. At times I feel it more in the steering wheel, others my seat and at times the gear shift. I don't believe it to be the engine mount(s) cause when it is vibrating I can shift into netural and the vibration does not change, I have also performed the 5K rev (FORD maitn. manual) and the engine is smooth (along with my expierence with bad mounts in my '94).
Ford Ranger / B-Series :: Front Brake Caliper Seems To Be Sticking?
Yesterday, I noticed that my right front brake caliper seemed to be sticking. This morning I jacked up the front end, and could barely turn the right front wheel when it was off the ground. So, I have concluded that that caliper is sticking. So, here is the question(s): what is the best way to repair this (new caliper, rebuilt caliper, or rebuild it myself), do I need to do both sides the same or can I just do the one that is acting up, and should I expect to pay. I have some mechanical ability, but that Haynes manual doesn't make too much sense to me. Getting it professionally repaired is extremely inconvenient, I need to be back at school (300 miles away) Tuesday evening, and probably couldn't get it in to get it done before then.
View 12 Replies