Ford Ranger / B-Series :: Hard To Get Out Of 2nd Gear / Engine Surges Then Starts To Lose Power
Aug 6, 2013
My surging/running down issue has returned on my '86 2.3l Ranger. I thought it was electrical, when things improved with the new ignition switch, but lately it's hard to get out of 2nd gear before the engine surges then starts to lose power. a poke of the gas pedal starts the who cycle over again. I pulled codes but it's hard to tell what the reader is saying either 33 and 34 or 334. The good thing is all the codes point to the EGR system. Looking for a diagnosis tree to determine if the valve is bad or the sensor is shot? They are both not cheap so I don't want to just throw parts at the problem.
View 14 Replies
Advertisement
I have a 1999 ford ranger 2.5L. When I turn the key to the ON position, right before the ignition turn, everything comes on like it's supposed too. However, if i try to change into reverse, the truck will start without me even touching the key. Also, if I start it using the key and try to go into reverse, the starter engages and makes the all to familiar grinding sound. I am completely stumped.
View 4 Replies
It's a 4 cylinder 5 speed, and once or twice a day when the light turns green and I go to put it in low gear, it just doesn't want to go into gear easy. It's like the syncro isn't happy or something. The clutch is depressed all the way and not dragging.
View 14 Replies
I have a 2002 sienna that will lose power to radio, air conditioner, power windows, surges when going down the road. So far it only last for a little while. And for a while now there has been times y…
View 2 Replies
I have a 99 ranger 4x4 4.0 V6 with 200K miles..I just had the slave cylinder replaced and bled however, it is still hard to get into gear and when at a stop light with the clutch pedal pushed in all the way the truck tries to move forward as if its in gear. I took it back to the shop and the mechanic says that the hydraulic system is working as it should and the problem could only be the pilot bushing failing and causing the trans to partially engage. The clutch and previous slave cyl only had 25K before the slave cyl failed and started leaking!!
View 12 Replies
I have a 1999 ford ranger 4x4 with automatic 5r55e and it had problems shifting smoothly into third gear. I changes the valve body gaskets and the (rooster comb) detent lever. Now it shifts very hard and has on first second and passing gear.
View 6 Replies
2000 Ranger 4R44e transmission.Hard shift from 2-3 gear and when i run about 35-40 mph and brake then acelerate it downshifts hard . Whats wrong with it?
View 14 Replies
Rebuild on the Mazda 5 speed transmission. My 1986 Ranger 2.3 Four cylinder has 280,000 miles and the clutch has never been replaced. It's not slipping but I'm having trouble getting it into gear from neutral. Was told that the release springs on the clutch plate have weakened causing the clutch to not release completely so figured it's time to replace it. It's done well the last 280,000 miles. The question I have : overhauling on one of these Mazda trans and how difficult was it. Any special tools required, etc...I see Autozone has a rebuild kit which appears to have bearings, seals and gaskets. Figured while it was out I would go ahead and rebuild it myself if I can. Rebuilt a few engines but never touched a trans.
View 4 Replies
2000, 2.5L standard transmission. IAC replaced about 2 years ago, DPFE sensor and vacuum hoses replaced early last summer. Truck has been running just fine until I washed it last night. Went to work, and when coming to a stop and pressing in the clutch, engine starts to race without coming back to idle. Had to turn the truck off in order to get the engine from racing. Same thing on the way home. What else can/should I be looking at? I did not open the hood to wash the engine off, so it can't be water from the wash.
View 7 Replies
My friend has a 98 ranger that has a lose connection on fuel relay under the hood, Hit a bad bump truck dies, Pop hood wiggle wire and your good till next bump. This got real old real quick. How this connection is made, Is it soldered?
View 2 Replies
My '90 Ranger is experiencing a pretty bad misfire after doing a tune-up. I changed the plugs (gapped to .045), wires, distibutor cap, rotor button, air filter, fuel filter, and cleaned the IAC. It had a barely noticeable miss before the tune up, that's why I did it. Now, it's pretty horrible.
At idle, it's definitely noticeable, and at cruising speeds (RPM's below 3K) it bucks and surges. The weird part about it is WOT runs are as smooth and (somewhat) powerful as ever! At idle in neutral it will revv up just fine without any hesitation as well.
First thing I did was check the firing order, again and again. Made sure all my wires were properly seated on the plugs and on the distributor prongs. Pulled the plugs back out, they were all clean and properly gapped. I pulled the wires off one by one to try to isolate the misfire, but every plug wire I removed made around the same impact on the motor.
Next I ran codes. KOEO, I got code 95 - fuel pump secondary circuit failure. Don't know what to do about this. Fuel pumps comes on at the turn of the key, relay clicks... KOER, I got 11 (pass code), so nothing there.
Then I hooked a fuel pressure gauge to the schrader valve on the fuel rail, and at idle pressure was a steady 35 PSI. I also removed the vac. line to the FPR while running to see if gas came out. I checked for vac. leaks as well.
Now not sure what to check now. I've checked everything I know to check, but nothing works....
View 14 Replies
I have a 1994 Ford Ranger with 4.0 V6 Automatic. The problem is when it idles it idles low and surges up/down and pushes a very small amount of black smoke puffs and smells like gas. I have installed new coil, new wires, new plugs, new ect, new crankshaft position sensor, and new maf. It has new intake manifold, new injectors, new alternator and it still does the exact same thing. Nothing is phasing it. I ran the key on/engine off test and got egr codes and a map sensor code, then ran the engine running test and got 998 and 126 code. The 998 code says that its basically a hard fault/ have no idea.
I do know this is a donor engine out of another year not sure what year, but i know when i ordered the coolant temp sensor the only ones that would plug into it are the years 1990-1993. Now here's my other question, why would the computer give me a map sensor code when truck doesn't have a map sensor? It has MAF sensor, and why egr codes? The truck doesn't have egr and never came with it. I do know I've unhooked battery and replaced the maf and its like it doesn't even recognize it? Could it be the ecm/computer bad or needs flashed?
View 5 Replies
My 3.0 with 216k miles has developed a rough idle and it progressively got better with new parts and cleanings. On startup it revs up to 2k then back down to 600. If I let it idle for about 8 or so minutes my Check Engine Light starts flashing. If I drive about for a little bit it stops and is just fine.
While the light is flashing I get codes P1000, P0305, P0306, and P0316. Which are OBDII Monitor Testing Not Complete, Misfire detected in Cyl 5, Misfire detected in Cyl 6 and Engine Misfire Detected on Startup (First 1000 Revolutions) respectively. Any other time the truck runs like a dream. Gets 20 city and 29.5 highway.
I cleaned my Mass Air Flow, replaced my Idle Air Control, SeaFoamed throttle body and vacuum lines, brand new coil pack, new wires, new plugs, new fuel filter, I've only ever run 91 octane, Chevron with Techron goes in at every oil change and B12 every other and I just ran 3 bottles of Lucas fuel injector cleaner.
View 12 Replies
I have a '92 Ranger with a 2.3 liter engine. She starts and runs a couple of seconds and shuts down. I'm thinking maybe a fuel pump is not putting out thepressure needed. Gotta go to work tomorrow and gotta get the truck running today.
View 2 Replies
'02 Ranger XLT, extended cab, 4X4, 4.0L SOHC, 5-speed manual, 114K miles.
Problem has occurred twice. After extended run time and engine fully heated, when I get home and shut it down, then attempt to restart within a short period of time, the engine starts very briefly, then begins shuddering violently and dies within a few seconds. Re-attempts to start result in a very shuddering attempt to run for a couple seconds, and then it dies. After a couple of re-attempts, it doesn't even attempt to start; just cranks over with no results. Has to sit about 7-8 hours before it will restart.
No OBD II codes; Passed, no codes shown. I purchased a crank position sensor, but haven't installed it yet: just a stab in the dark after hearing other people's experiences with other vehicles.
First occurrence followed a lengthy trip in heavy stop-and-go traffic. Shut it down when I got home, then attempted to re-start after a few minutes to run a short errand. Sat for two days without any re-attempts; then restarted and ran fine on first try a couple days later.
Second occurrence followed a couple hours of hitting yard sales with the neighbor, in which time I did not shut the truck down; just left it idling while we perused the sales, for fear it wouldn't re-start. Reckon it's a good thing I did, 'cause when we got home and I shut it down and attempted to leave again shortly thereafter, it malfunctioned as described.
Retries failed after sitting 4-5 hours, but after eleven hours of sitting, it started right up and ran normally.
View 3 Replies
My Daughters 2004 Ranger has about 195K the power steering reservoir is full it turns to the left as it should (assisted power steering) turning to right there is no power steering (manual Rack) I am thinking the issue is most likely in the steering rack..
View 2 Replies
1994 Ranger .. Last wednesday I had to get a jump because the lights where left on. Everything was normal on thursday. Friday morning. I went to go start the truck and notice that it would try once to start and then try a second time and it would start. Today I was driving it. The check engine light came on and when I get the RPMs up to shift up, I would loose all power and have to wait till it gets down below 10mph before I would get the power back.
View 8 Replies
My 40 Ford pickup is on an 86 Ranger chassis and uses the stock Ranger steering gear. My question is about the connections on the steering box. I'm using a GM power steering pump and several steering gear vendors have told me that outside of needing to adjust the pressure for the correct feel, the combo works. I fired the truck for the first time tonight but the steering wheel went crazy, shaking around and finally spinning on it's own to a hard left.
Some quick research leads me to believe that I have the lines reversed but it would be great to know for sure. I did manage to find on e diagram of a Ford PS box on Google and it shows the lines reversed of what I have set up on my truck and I can't for the life of me remember how I figured out what the plumbing should be when I installed it. Which port on the box is the inlet and which is the return?
View 2 Replies
Im wanting to get more power out of my 94 auto supercab but I don't wanna kill mpg it has 3.08 gears I was thinking swap to 3.55 to keep mpg would there be noticeable power difference?
View 6 Replies
The reverse gear went out in my 97 ford ranger with automatic transmission. I took the transmission out and replaced the reverse band, cleaned everything up, put it all back together and back in and filled it up with fluid. Unfortunately, between me and my assistant, we did not secure the pump correctly and sheared the ears off it. It made a racket when we started it. It would go through all gears while jacked up but when on the ground it had no power. It would barely move. And there was no fluid coming through the pump when I cracked the lines. We pulled it all out again, took it to a shop, put on a new pump and had them reassemble it all and we put it back in, making sure to do it right this time. But I still don't have the power I had before all this. It's very sluggish in all gears. There was no racket on start up this time. And when I crack the lines there is intermittent fluid loss but not a constant flow. I really don't want to pull this thing again. What am I doing wrong?
View 2 Replies
This truck has been giving me tranny problems for a while now. About a year ago, stopped in traffic in neutral, I attempted to shift into 1st but it wouldn't go into gear, not reverse, not any gear. Eventually after a minute or so of trying it reluctantly went into 1st. About 6 months ago I started the truck after being parked and again it wouldn't get into gear. Shut it off, tried to get it into gear, nothing. Checked the hydraulic fluid reservoir for the clutch and it looked a little low so added a bit and after that it shifted into gear (maybe coincidentally). Now about a month ago, it again wouldn't shift into gear after being started. I checked the reservoir again, looked fine this time. Shut the car off, attempted to shift and this time shifted with ease
Something that I've noticed in the past year is that sometimes now when I shut the engine off it doesn't run down smoothly; kind of slows then clunks to a stop. Didn't used to do that.
View 2 Replies
