I've a 1994 Ranger XLT 4.0L with a missing fuse panel cover. I'm trying to get the horn to work and we've traced the problem to a missing fuse. Unfortunately, there are 3 empty fuse slots and no info on their rating or use. Where I can get the proper info. Truck was a salvage, no ops manuals, and sloppy work putting it together.
View 14 RepliesWas riding along a couple of days ago and felt something odd under my left foot. When I stopped I reached down and discovered it was the dash fuse cover panel. I went to snap it back into place and no snap; it wouldn't pop back into place or stay put at all. Just keeps falling out. It was sufficiently annoying that I ordered a replacement, but that one's not staying in place either. The only other thing I can think of is that the surrounding lower dash cover may be warped, but nothing looks crooked or out of place.
View 1 RepliesI have a 98 Ranger with a 3.0 (5 speed) that has 254,000 miles on it. I drove it to town this morning (8 miles) and it ran normally. I stopped for just a few minutes at a house and when I re-started the truck, it was missing very bad and the CEL came on. It wouldn't haul itself in anything higher than 3rd gear. I decided to try to make it back home. I drove it less than two miles and it cleared up and started running perfect again. I came home anyway and read the code with my scan tool.
It said that I had a miss fire on cylinder #5. I erased the codes and shut the CEL out and its been running perfectly ever since. (I have put about 150 miles on it so far) If it does it again, I will start by replacing the plug wires. I have already done that but its been a long time ago. The plugs have been replaced twice as well. I was wondering if it could be something other than electrical like a dirty injector or maybe the compression rings lined up and it momentarily lost compression.
I have a 2001 ranger 2wd with a 2.3. It has a miss when acceleration. There is no check engine light. I have changed: fuel filter. Plugs, wires, crank position. Sensor, cleaned mass air flow sensor. Ran 2 bottles of injector cleaner in it. Still missing???? It runs and idles great. Just has a miss in the lower RPM's 1000-2000 then goes away. I really don't wanna take it to a shop. What do you all think??
View 11 RepliesMy truck has had this annoying tendency to drink coolant. I believe I took care of it by replacing the thermostat gasket. Not so, it drinks about a quart every 50 miles - so quite a bit really.
Finally bit the bullet and took it to the dealer so that they could figure out where the coolant was going.
Answer I got back was - timing cover gasket, water pump, lower radiator hose.
The water pump appears to be good, its just the gasket that's bad. So my question is - how significant is the timing chain cover leak? Poking around online it appears to be reasonably common, but sounds very expensive. The dealer indicated it would be 2 days work minimum.
Bought an 01 Ranger 4x4. The 4wd doesn't work, no clicking in kick panel, lights etc. got a used unit and plugged it in, blew my brake switch fuse (#9 on side dash) I failed to disconnect the negative ground ( oops) the original part # in the truck is
1L547H417AC
Do I need to get the exact same part number on a donor vehicle? I can get a CM for 25.00 at a local pick n pull, they have a lot or explorers there. Also will this solve my fuse issue? The truck sat for a few months and the battery died before I owned it.
85 ranger 2.3 fuel injected misses at high acceleration. Fairly new plugs and wires, just replaced the timing belt, pretty new fuel pump in tank, new fuel pressure regulator and pcv. It idles well, starts up and drives pretty well until you get it in 4th and really bog it down. Could be timing issues but I'm pretty sure I did everything right when I put the belt in. What it could be? I know when the tank fuel pump went out, it did something similar for a while...
View 9 RepliesI've got a 1988 2wd Ranger with a 2.9l v6. I just recently got it running. It has been setting for awhile. I replaced fuel tank, both pumps, fuel filter, Plugs, Wires, Cap, Rotor, TPS. It ran great for about 100 miles. Then yesterday on my way to work about 4 miles down the road it started to miss/stumble especially at about 55mph while in overdrive. When I got home I pulled the codes and I got KOEO 22 Map sensor signal out of voltage(engine off), 53 TPS signal voltage to high, 95 Thermactor Air System Problem, or Fuel Pump Monitor signal, indicates circuit problem.
KOER I got 21 ECT sensor signal voltage out of range or loss of signal during normal operation or Crank Sensor problem, doesn't have a crank sensor I believe. But I did change the ECT sensor and it still stumbles and seems like it misses. Noticed it is sluggish getting up to speed kinda surges and bogs. Im at a loss it isn't showing any more codes. Checked all plug wire connections and made sure everything was making connection. The only other thing I can think of is that the ignition module on back of distributor is going bad. Not advancing the time correctly.
4.0. I'm having what feels Like a Miss on Light throttle/cruise. Once warmed up it's fine. Idle is fine too. There is No CEL/Codes.
View 14 RepliesDescription: It will crank over forever but not start. New timing belt water pump, etc, so it is not timing. tried different fuel pump relay. no luck. new fuse no luck. The radio fuse also shorts and blows when I change it. Headlight does not come on, but the cabin "ding ding ding" sound plays. Marker, turning, reverse, and brake lights work.
CHECK ENGINE LIGHT does not come on during key turn. I may know what caused it or it may not. Before all of this happened, my audio system fuse under the hood blow. It blew again after I installed a new fuse (immediately).
One day, the wires on a portable cigarette light pump snapped and the two wires had been touch. I noticed the truck stalled several times when letting off the gas and coming to a rolling stop. The fuel pump relay makes a click noise when I turn the key
I live in Kansas and was home in Georgia for the last 2 weeks. The truck drove great there after a fuel up started missing and surging at 50 to 70 thought it might have been bad fuel. waited till it was low added Lucas fuel treatment and premium gas still was doing it. no check engine light. went to Advance and fuse for light was blown they checked and was getting mass air flow code. unplugged it and seemed to be better, not perfect but better. plugged it back in and went to do it again. Changed mass air flow night before the drive back to Kansas. Ran well from Savannah to north Georgia then started doing it again the rest of the way home. Going to have advance check code again.
View 12 Replies1998 4.0 ... She only misses about 30 seconds during stone cold startup. I figure it's probably the plug thats hardest to reach ? Isn't that the way it always is? From the hood I can see only one spark plug, so I figure I'll do all the plugs. Is there any right or wrong approach to the plugs? I did the thermostat today, but this plug job looks like it's gonna be a bitch. Time for some skinned knuckles Next is the right side O2 sensor, that looks like fun too. But I gotta say, this little truck is sweet. Great visibility and easy to park in the city. I really like her. She's a keeper. She needs some new sway bar bushings too, but no surprise with 127 K on the clock.
View 5 RepliesMy 2000 Ranger standard 4.0 4x4, started spitting and sputtering the other morning just when i was gone up hills then it would quit doing it. The other evening it got to where it don't idle, missing very bad, and wouldn't even pull itself up a slight grade, and the wife said there was flames and sparks coming out the exhaust. Now it wont even try to start, it just turns over. I put a different coil pack, wires, and plugs, and still nothing. I pulled the gas line off the frame fuel filter and its shooting gas out, and I got gas to the check port on top of the engine.
View 5 Replies1996 4x4, manual trans. Wants to kick out of first, and when shifting into 3rd I have no gear. Doesnt grind, just goes in as though it were neutral.
View 4 Replies2001 M B3000 v6 my sons truck w 122k. He is overseas and I took it to deliver a CB750 bike to my brother in law... 4oo miles away from my place.
In the middle of nowhere TX it developed a bad miss or knock, almost a shudder in the 2 to 3 k rpm range. Idles ok just below 1k runs fine at 70 mph as long as the rpm is near or over 3k.
Not sure I want to turn around and drive back the 400 with it running like crap. I will take it to Autozone and pull codes tomorrow a.m. but what should I expect?
I just got my grandpa's 2002 Ford Ranger Edge after waiting years to obtain it. It runs great the only problem is that there is NO power to the radio what so ever. The truck belonged to the family and every one drove it but no one knows what happened.. There is no power to Fuse 28 however 12V to all other fuses that have to deal with the radio.
View 12 Replies2000 Model, The fuse keeps blowing on this. I thought it was the cruise control fuse because the cruise kept not working and when I replaced fuse it would work. Only for a little though, then I looked at manual and it says the fuse is for the brake position switch. I am presuming this is just like the old days and that is the brake light switch under the dash. They use to have two wires now there is like five. Anyways I do not see any bare wires or anything that would blow a fuse, is it common for these switches to go out or what??
View 13 RepliesMy dad's 1991 Ford ranger 3.0 2wd just died on him when he was driving home and I checked to see if the truck had a spark and it did not so I replaced the ignition control module, then ignition coil, then distributor and rotor cap(plug) and I put new plugs and wires on it a few months back too. I also checked to make sure that the timing chain was working as well (while I had the distributor cap off). Then I realized that the EEC maxi fuse was blown. I then found a fourm that said it might be the relay so I replaced the EEC and the fuel pump relays while I had them both out. Every time I put a new 30 amp fuse in the EEC slot and turn the key to start it the fuse blows and the truck won't start. What might be wrong?
View 1 RepliesFound a tee on the heater hose leaks when it warms up. Appears the PO had noticed it but put a hose over it and now is leaking around behind the valve cover. This is a hard plastic line around 5/16. No online parts show it as being available. Is there a fix for this ?
I would bet several others have had this problem as it lays right on top of the flange of the valve cover where I think it would rub a hole pretty quick.
1989 Ranger 4X4 4 cylinder....
I have 2000 V6 3.0 Ranger and it has sprung a small coolant leak from timing chain cover gasket. I think just few drips after driving a while since I don't see significant drop in coolant level (Took a month to notice level dropped in reservoir) and did not see an active leak while idling. No water in the oil.
The proper repair would be to replace the gasket, but for the age and condition of the truck, I don't think it is worth it. Searching for a cheaper solution, I found K-Seal and see lots of reviews with success. Will it damage the cooling system in anyway? I think it would be worth a try even if it doesn't fix the leak as long as it does not cause any harm.
My 2000 Ranger has been leaking fluid around the front Diff cover so I decided to pull the cover and reseal it. It was obvious that this was going to be a tight job but I didn't anticipate running into a bolt that can't be removed because interference from the front cross member.
View 3 Replies