Ford Ranger / B-Series :: Front Brake Caliper Seems To Be Sticking?
Oct 8, 2005
Yesterday, I noticed that my right front brake caliper seemed to be sticking. This morning I jacked up the front end, and could barely turn the right front wheel when it was off the ground. So, I have concluded that that caliper is sticking. So, here is the question(s): what is the best way to repair this (new caliper, rebuilt caliper, or rebuild it myself), do I need to do both sides the same or can I just do the one that is acting up, and should I expect to pay. I have some mechanical ability, but that Haynes manual doesn't make too much sense to me. Getting it professionally repaired is extremely inconvenient, I need to be back at school (300 miles away) Tuesday evening, and probably couldn't get it in to get it done before then.
View 12 Replies
Advertisement
2000 Ranger, see my sig.
Just had to swap out the pads on my truck yesterday. The pedal was pretty mushy and I was getting shaking in the steering wheel when the brakes got warm. Shaking wasn't all the time, only after they had been used quite a bit - say after city use and the brakes had to be applied suddenly. So I popped off the tires and swapped out the pads and replaced the brake fluid - flushed it.
On the driver side front, the pads barely had any real wear and the anti-rattle clip was all messed up. It was installed properly, but it looked like the pads had smashed into it. The rotor appeared to be warped, or at least out of round - but just barely. You could see it wobble slightly in one spot if you spun the hub with the caliper removed. The caliper itself was sticking slightly.
I didn't see any evidence of damage, the brakes flushed just fine although the fluid was incredibly dirty (because I haven't done it in a long while). On the passenger side front, the pads were worn down to the level I would have expected given the mileage. The wear was even.
My question ultimately is this - is the out of round hub the culprit here? Might there be something else going on like a caliper problem? Ultimately I plan on having the rotors surfaced - one of them certainly needs it and with new pads I might as well do it anyway.
View 5 Replies
I know this has been talked about many times and how to solve the issue but thought I would ask some other questions too. Earlier in the summer, I did grease the slider pins as preventative maintenance. I don't drive my truck all that much and when I used it yesterday, (about 30 minute drive) I came home to burning brake smell. I'm wondering if enough heat would cause the caliper to go bad? Should I just grease the pins again or change out some parts?
View 6 Replies
One of the pistons in my driver side (UK) front brake caliper is sticking, so I've bought a second hand caliper just to fix the problem until I come to sell my pri in a month or so.
View 15 Replies
2005 Toyota Solara my front driver side caliper was sticking and heating up a couple months ago... replaced the caliper and the rotor... still had the same problem. I would drive it, it got hot and stuck, after I parked for a little while it slowly released. Talked to a couple of mechanics and they both said undoubtedly I had a bad flex hose and it was collapsing with pressure and then will release... I changed the flex hose and flushed the fluid and it was immediately fixed...no problems.
Drove the car for a month, went to South Carolina and back and then a couple days ago the same thing started happening. Talked to a mechanic, he told me that the new caliper may have gotten fried from over heating before I changed the flex hose... Got a new caliper today (warranty) exchange... changed it out and still have the same problem. When it sticks I can release the pressure by opening the bleeder valve so it seems like the flex hose issue again... my only thought now is maybe the new flex hose is a bad one and someone mentioned the proportioning valve.
View 9 Replies
My son and I were doing a transmission flush and while we had it on the lift, I noticed the oil pan gasket was sticking out in the front quite a ways. I assume its time for a new one. Is there anything I need to know having never dropped the pan on this truck? Is this a common issue?
View 14 Replies
My left brake caliper locks up on me. I have replace it, the brakes , and the wheel bearings. when im driving down the highway and go between 45 -55 my front end shakes really bad and i start to lose power.
View 8 Replies
Have 50,000 mile on my 2011 F350 6.7 and up until today the truck has been flawless. This is my weekend vehicle and sees very light duty hauling fishing gear to my boat (100 miles hwy) and pulling my 7x12 enclose trailer with goose decoys. On a couple of occasions pulling my 29 CC from marina to my home and back. Took truck in for oil change and tire rotation, service advisor informs me I have 2mm on rear brakes and 3mm on fronts. Not sure why rears have more wear than fronts. Schedule to have brakes done for today and now find out that front right caliper is sticky and they want to replace both front calipers. I cannot believe that a 2011 SD F350 with 50,000 miles and of that mostly highway needs brakes let a lone calipers are going bad. Service manger tried to tell me that brake fluid should be replaced every 2 years, to which I responded that I have Ford perform all scheduled maintenance. He went on to say that this is not scheduled maintenance, wtf bs is he telling me, if it is necessary then it would be scheduled maintenance. Truck gave zero indication of stuck caliper, no sound and no excessive brake dust on wheel.
View 14 Replies
I just hit a pothole on my way home just now and now my front right caliper is sticking. It happen about 10min from my house. As soon as i hit the pothole I can feel my truck pulling to the right and felt like there was some resistance when i was driving. I got home and peeked my head in the wheel-well and i can smell the brakes burning and smoking a little. How would hitting a pothole cause a caliper to stick. Is there anyway to unstick it or am i gonna have to change that caliper out...
View 8 Replies
I heard a grinding noise coming from the right front tire last night. Came home, removed the wheel / tire and noticed the caliper was stuck pushing the pads against the rotor. I pushed the caliper pistons back in so they're not frozen, just sticking.
View 14 Replies
My front disks are pulsing & the thickness is near minimum, so I guess I'll have to replace them soon. Is any particular brand better than others?
These stock ones are made by Bosch and I'm not impressed with their lack of resistance to warpage. I see "Drilled and Slotted" available at Rockauto. What's your experience? Are they any good?
View 1 Replies
1998 ranger 5spd... I have 117k miles on this little ranger and I recently took it on a little trip and since that trip it has a ticking noise under the hood as if the lifters were sticking. I believe it has hydrolic lifters in it. I put some sea foam in it 200 miles ago and changed the oil about 50 miles ago. I used Valvoline full synthetic and it seems like it has lessened the tick and it drives a lot smoother, in my opinion. Is there any thing else I can do to relieve that ticking? It is more noticeable when the engine first starts and is louder if i push down harder on the gas. It is not preset if i do not put that much pressure on the gas.
View 6 Replies
I have a 2001 ex. 4x4 6.8 v10. I have been having vacuum issues and brake issues lately. My front brakes seem to be sticking, some times they drag some times the don't squeeze when I step on the brake causing uneven wear and pulling when I stop. Also feels like I have no power assist. I also have a vacuum issue with the auto setting on the hubs, they don't engage I have to manually lock them and sometimes my a/c stays on defrost. And my cruise control doesn't work, the light comes on and love done the self check but it doesn't show anything is wrong. Could I have a bad brake booster?
View 5 Replies
98 Ranger Front brake lines Too short! they kink in sharp turns and wear out then start to seep then eventually leak and need replacement. Checked parts references and the lines have been considered stock. Not sure if I have a 1/2 year model.
View 1 Replies
My front driver side brake line broke. It had a typical double flare fitting at the caliper but at the distribution block on the other end it had a flared fitting that would be used on a industrial hydraulic unit. I took it to the NAPA store and they told me to cut the nut off the old line and put it new line and double flare it. I did and it leaks. Do I need a special fitting on the end that goes the distribution block?
View 2 Replies
My buddy has been having a strange problem with his 275,000 mile 2003 F150 2wd. The right side caliper will lock up out of the blue and will not release for anything. We put 3 news calipers on it within a 4 week period thinking that we had a defective one but no change. I am thinking either a bad brake line or, more likely, the front abs block...
View 1 Replies
My teenage son just bought his first car, a 1991 Ford Explorer XLT 2-wheel drive. I had it checked out by our mechanic before I let him shell out the money, and everything seemed OK. It's the prototypical low-mileage car (127k actual, confirmed by Carfax) owned by a little old man who took good care of it (stack of service records a foot high) and didn't drive it very much.
Earlier this week ... he'd driven it for about two weeks with no issues ... the left front brake caliper locked up on it, to the point where it heated up enormously, the pads and rotors got so hot they were discolored and some transmission fluid got blown out by the strain.
He took it to our regular mechanic, great guy who we've used for years and has worked magic with our cars, he got into it and he diagnosed the problem as ... I hope I'm explaining it right ... a little pin or piston or something in the caliper was upside down. He put it back in the right way, and everything seemed to be OK, although he said my son would probably end up needing a brake job sooner than later because of the way the pad got ground down.
FYI, master cylinder is full of fluid, our mechanic couldn't see any leaks anywhere. Although when we took the car to the mechanic, my son tried to back it up to get a better angle at getting into the service bay, and the pedal went to the floor.
Fast forward two days, and danged if the same thing didn't happen with the right front caliper, seized up although he didn't get it as hot as the other time, parked it a lot quicker. And of course it happens on Friday going into the weekend, when our mechanic isn't working, he won't be able to do anything until Monday, which leaves us scrambling trying to get everyone to work, etc., down one car.
Doing a little online homework ... which we probably should've done before my son made this purchase ... I'm seeing a lot of brake issues with '91 Explorers. I asked my mechanic if he thought there was some ABS-related problem here and he said he didn't think so.
I will say that the car apparently sat undriven for a long time, which I know can unleash a lot of issues. What might be going on here? Do we just need to go ahead and replace the calipers, any hoses, etc., as preventive maintenance?
View 1 Replies
I have a 99 150 4 wheel drive..5.4 ..auto...110.000 mile.....notice when driving in town in hot weather....when you are on and off the brake petal a lot....stop and go..etc.....the truck starts to hop or bounce....some....I got out ..and notice the right or passenger side front brake seems a lot hotter than the drivers side......but ...when it does that....the steering wheel doesn't pull to one side...when changing pads before ..notice no one side worse for ware than other...thinking it must be sticking brake calipers....they don't do this say on interstate driving even when on and off the petal some...
View 1 Replies
what i have is the driver's side door on my 1999 ranger is hard to open, the door seal sticks to the door and makes it hard to open, i am afraid of breaking the door handle off, is there any thing to clean seal with to make it not stick? the seal is not sticky to touch neither is the door but when out in the sun for a while they stick together, mechanic told me to spray with wd40 that didn't
View 2 Replies
I read a reference to the front brake caliper bracket bolts being one time use torque to yield and must be replaced every time they are loosened. Is this true?
This is on my 06 F-350 in my Sig.
View 3 Replies
2001 F250 SD diesel. Brakes have been working fine with no pulling. They just started to squeal recently so I knew it was time for some new pads.
I'm having a problem that seems to plague me often when I try to replace disc brake pads. I can't get the twin pistons to go back in to allow room to get the new, thicker pads in.
I unscrewed the cap to the master cylinder and used a spreading tool (that came in a brake kit from Advance Auto Parts) to compress the pistons. No movement.
I put a lot of force on it. No piston movement.
I unscrewed the bleeder screw and tried again. No movement.
View 4 Replies
