Ford Ranger / B-Series :: Fan Only Work At High Speed / Blower Motor Hose?
Nov 13, 2012
I recently bought a 96 ranger.I noticed the fan did not work but for high. I search the internet and found how to remove it and discovered a mouse nest(village) which basically took over the housing where the evaportor core,blower motor resides. I bought a chilton but cannot remove the housing around the core so I cleaned it the best I could(air compressor and vacuum and disinfectant)...
I had to buy a new blower motor and resistor. However, I cannot find the hose that attached to the blower motor?-mouse had chewed a hole in the one- I've looked and found serveral differents names for it but seems I cannot find it at my local parts store.
My question is- is this intake hose? vent hose? I'm guessing I will have to go to dealer or, if I know the name I can look it up in a salvage yard?
View 14 Replies
Advertisement
I've got a new to me 97 Ranger that the blower has never worked in and I can't get it going. I've checked the fuse. That's good. Tested the relay. That's good. Did an ohm test on the power switch for the blower. It's open in the "OFF" position and closed in the other positions. I've got continuity through the speed selector switch. New resistor and pigtail because the other one was nasty looking. What seems odd to me is that I've only got power to the blower motor relay at one terminal with the switch on (number 30 I believe). In addition, when I test the plug for the motor itself with my test light, one of the wires (org/blk I think) has power only when the switch is off. And I ran power straight to the fan from the battery and it spun right up. What am I missing?
View 8 Replies
Have a 2004 F-250 and blower motor speed 3 is not working..replaced resistor pack with Motorcraft part and everything works except position 3 ....
View 6 Replies
I have and 07 F250 and the #2 speed for the blower motor don't work (hasn't since I bought it) I read that the most common cause of this is the resistor under the hood on the firewall so I replaced that and still no 2nd speed??? Where I look next? Motor itself maybe?
View 11 Replies
I am not great with electrical but can manage. Here's the deal, Ihave a 1997 ford ranger 2wd 2.3L 5spd with a/c 233,000 miles i just replaced the heater blower motor resistor as the old one was rusted bad as was the pig tail going to it bad that one of the terminals broke off and was rusted in the harness so i replaced the plug as well problem is i still have no fan if i jump it it works but have no power at the plug for resistor or motor and no power at the switch inside the truck I do have power to one terminal where the relay plugs in, where to look next?
View 14 Replies
with a new heater core, new blower motor, and new resistor and no heat, what would be the problem? gonna check the thermostat tomorrow.
View 2 Replies
I replaced the blower motor resistor on a 2010 F150 with dual climate control where the blower was stuck on high.
After replacing the resistor, now the lower speeds work fine, but when placed on high speed, the fan completely shuts down. Replace with the old resistor, and it only runs on high.
How to proceed, or what else might be the problem?
View 7 Replies
My blower motor does not blow hard on high. 2009 AVALON.
View 3 Replies
Wiper problem is that they only work on high. The symptoms are as follow. The relay is working as the controls are ran thru the intermittent steps. I have tried two control switches and they acted the same. So, I believe the problem is in the motor. There doesn't appear to be any wire problems on the plug so it must be inside the motor. Could this be that grease problem inside the motor and it just needs to be cleaned and re-greased?
Radio, Has power to the plug but doesn't work at all. It doesn't appear to have a head unit fuse that I keep reading about. I have not tried to hook it up direct yet but will try that tonight. I am trying to get this truck ready to sell and need to get these items cleared up.
It is a 2001 XLT Extra Cab 4X4 with a 3.0.
View 14 Replies
My son just purchased a 1996 Ford Ranger 2.3l 5 speed it is a nice little truck. But I have a question when you press in the clutch it acts like the choke has come on it idles way to high. When you come to a complete stop it is a few minutes before it goes back to its regular idle. Is it suppose to do that?
View 9 Replies
I have an '02 F150 XL. 200k miles. My a/c blows cold, and I have every fan speed, but it just doesn't blow very hard. I replaced the blower motor thinking that would work, but that did nothing. I've been told to clean the evaporator core, but I don't know where that is. How to do that, as well as any other part causing the problem.
View 14 Replies
Well my blower motor only blows on high which IMO points to the resistor, went and bought one and still only blows on high. Tried to test the plug that goes to the resistor but couldn't get anything, shouldn't there be 12v going to the plug and then step down to the resistor until high is selected then 12v bypasses the resistor all together? Blows strong and cold, too cold actually since we cant turn the blower down so we have to turn it off for a few minutes.
View 9 Replies
I have google it looked all over was told it was under the hood next to the fan even shown a photo when I went under the hood right were the resistor was in the photo there was a long black box about 4 inches long and 2 inches wide. looked nothing like the photo.
So I went back on line and read that its above the passengers feet you take a few screws off after you take the glove box off and it should be there. Well after taking 8 screws off I find nothing but a coil behind there. Nothing that looked like a resistor.
2006 f350 diesel?
View 11 Replies
I bought my youngest daughter a used 2009 Ford Escape (out of warranty) a week ago. Manual HVAC controls, 3.0 V6, AWD, 73K miles. The HVAC blower motor do not seem to move any air on speed 1 and 2. However speeds 3 and 4 appear to operate normally. Speed 4 noticeably puts out more volume of air then 3. Each 3 and 4 operator what seems to be normal speeds for their setting.
I would normally suspect resistor but my experience is usually that you have all or nothing not it's partially working like this is. I don't mind throwing a new resistor in there and trying it but I rather come up with a better way of troubleshooting it then throw parts at it.
View 5 Replies
What is the testing procedures for the blower motor controller on my 2009 150 Lariat. In the old days it was called the resistor but now it is computer controlled for the dual climate control. My fan is stuck on high, the fan switch does work(the bars on the display change when I push the fan speed button). The climate control works also, just blasts you with air and the temp is changing a lot due to the fact of the fan on High. I am 99% sure it is the blower motor controller, but I would like to test the controller.
View 14 Replies
When turning the ac/heat on it will only work on the high setting and none of the lower ones - 2003 f250 .....
View 3 Replies
Where I might be able to find a vacuum hose routing diagram for a 2.9? I have searched high and low but with no luck.
View 14 Replies
My 2010 Expedition Limited AC seems to be stuck in the highest fan speed setting. Changing the setting on the panel control do nothing to change the speed. But you can adjust the temp and it will respond. It is a dual control unit. When I try to turn the system to off completely it will go to what I believe is the vents and stay on full blast. If I turn the truck off and on again the whole system remains off until I turn it on again. The only way to turn it completely off is to turn it to off mode and turn the truck off.
View 1 Replies
Currently My AC / Heat blower motor operates but, speed 1 and 2 are the same, 3 and 4 are fine. I replaced the blower rheostat that is located on the firewall, but still no difference in fan speed.. A few years ago the blower only operated on Hi and the rheostat was the problem then.
View 3 Replies
I don't know if its a coincidence but it rained hard all weekend and went to work this morning to find out the blower motor only on 4(high). I checked the plug going into blower motor and it looks dry and clean. is there a common occurrence with this? What to look for?
View 14 Replies
I have a 1989 towncar. The blower motor works in any selection (vent, panel, hi-low, mix, defrost) but does not work in the "floor" position. It also turns off in the off position as it should.
I changed out the entire climate control assembly with another one from a junkyard. I thought the function selector electrical switch might be bad. However, the blower motor still does not work.
View 1 Replies