Ford Ranger / B-Series :: Engine Starts Very Briefly Then Begins Shuddering Violently And Dies Within A Few Seconds
Jun 14, 2017
'02 Ranger XLT, extended cab, 4X4, 4.0L SOHC, 5-speed manual, 114K miles.
Problem has occurred twice. After extended run time and engine fully heated, when I get home and shut it down, then attempt to restart within a short period of time, the engine starts very briefly, then begins shuddering violently and dies within a few seconds. Re-attempts to start result in a very shuddering attempt to run for a couple seconds, and then it dies. After a couple of re-attempts, it doesn't even attempt to start; just cranks over with no results. Has to sit about 7-8 hours before it will restart.
No OBD II codes; Passed, no codes shown. I purchased a crank position sensor, but haven't installed it yet: just a stab in the dark after hearing other people's experiences with other vehicles.
First occurrence followed a lengthy trip in heavy stop-and-go traffic. Shut it down when I got home, then attempted to re-start after a few minutes to run a short errand. Sat for two days without any re-attempts; then restarted and ran fine on first try a couple days later.
Second occurrence followed a couple hours of hitting yard sales with the neighbor, in which time I did not shut the truck down; just left it idling while we perused the sales, for fear it wouldn't re-start. Reckon it's a good thing I did, 'cause when we got home and I shut it down and attempted to leave again shortly thereafter, it malfunctioned as described.
Retries failed after sitting 4-5 hours, but after eleven hours of sitting, it started right up and ran normally.
View 3 Replies
Advertisement
I have a 2005 ranger SOHC 4.0 new rebuilt engine It starts then dies after a few seconds then doesn't start at all unless it sets for a few hours or over night and will do same thing. It has 60 psi on fuel rail, good spark I'm starting to think my PCM is causing all this?
View 14 Replies
I just replaced the water pump and put it all back together, now it won't run well enough to drive. Checked vacuum system, all sensor connections, hoses, gas cap, changed fuel filter, I can hear the fuel pump kick in, reset system with battery disconnected and have looked at everything I can think of so far.
Now - starts fine, idles about 10 seconds and then begins to idle rough and dies. If I use the throttle I can often keep the idle up, but then backfires or acts like no fuel and again dies. Used fuel cleaner and made sure there was plenty fuel in tank.
I am looking at replacing sensors at this point but which one first?? They get a bit expensive real quick.
View 5 Replies
I've got an issue with my 92 2.3 ranger.... sitting at idle for 30 or so seconds it starts to chug and sometimes dies.... I can hit the throttle and its fine for another 30 or so seconds.... while cruising on the freeway after about 30 minutes it starts to cut out badly... let out of throttle for a few seconds and it clears up and drives fine...
Here's the part that has me confused... pulled codes yesterday using a innova scan tool...
koeo were 4, 10, and 538...
koer were 111, 10, 157, 158, 181, 327, 328, and 334....
How does it give me a 111 pass code and then still come up with all the other codes? I am thinking my ecu may be screwed.....
View 4 Replies
I have a '92 Ranger with a 2.3 liter engine. She starts and runs a couple of seconds and shuts down. I'm thinking maybe a fuel pump is not putting out thepressure needed. Gotta go to work tomorrow and gotta get the truck running today.
View 2 Replies
'88 Ranger 2.9L V6 starts and runs but shuddering. Most noticeable when shifting and revving the engine. Will a dead cylinder cause this? How do I check?
View 2 Replies
Ole girl finally let me down, or I let it down at 224,000mi. Started just fine one early cold morning and in about 30 seconds started stumbling and down for the count she went. Acts like it wants to run but will only stumble.
Checked inertia switch (ok) and all vacuum lines/caps appear to be fine. I was kind of due for new set of plugs/wires and a fuel filter. Replaced all didn't see any problems with the old when pulling. She will run for a few seconds, but stumbles and not smooth while running. Checked fuel pressure KOEO 40psi steady. I can hear fuel pump charge system per as usual.
Seeing as it is super cab checked for chafing on wiring to fuel pump under cab. Looks fine. I've heard tell could be alternator, which seems odd to me. Wondering if it would be worth pulling it off and taking it in for a bench test? Maybe I missed something. I know the intake gasket is suspect.
View 14 Replies
The truck started acting up while driving. It would shut off (no miss or anything), but would start again. Now it is sitting in the driveway and wont run more than 3 seconds. The fuel pump has been changed and did not work. The fuel pump relay is new and did not work. I read that the fuel pump goes to another circuit after start up. Could it be running to start and then shutting off? Inertia switch is not tripped. Where to look next. 1992 Ranger 6 cylinder ....
View 10 Replies
My 2003 2.3L used to run bad... it had a lot of lag to it when i would try to accelerate. The check engine light was on so i got it checked, and the reading said o2 sensor high voltage or something like that... anyways, i purchased a new sensor (i researched, and found there is only an upstream o2 sensor), replaced it, and the truck ran WAY better, no more lag during acceleration, it was crisp. As i was driving home one day, i was accelerating up a hill, and at about 4000 RPM, the truck almost dies and starts sputtering.
The check engine light started flashing, so i new it was serious, but luckily i was able to make it back to my house. When i got home, i looked under the hood and noticed that #2 & #3 spark plug caps had popped off the spark plugs. What I don't understand is what would have caused that to happen in the first place.... Is it a clogged Catalytic convertor, or is the o2 sensor bad.... Ive read different opinions and technical diagnostic possibilities, but man, i don't want to throw a bunch of money at a truck that I'm really going to have for a few more months. but I need to get it fixed in the mean time.
View 2 Replies
Recently, today in my 87 Ranger suddenly the engine dies and all electronics in the cab fail.
I noticed under the hood that the fusible link connected to the battery and an orange and black wire was smoking. Tracing this line i found that it leads to the ignition switch, as well as some other places.
There is another fusible link and the junction between the yellow ignition wire and the orange and black wire from the battery. This fusible link also was failed.
I'm planning on replacing the fusible links tomorrow but in case that does not fix it, where to look next.
The problem only occurs when the key is in the ON position. I'm thinking maybe I could do some tests with a multimeter on the ignition switch but am not sure of the details of what I should test for.
Summary: Fusible Links C, and E burn out when the ignition is in the ON position.
View 6 Replies
Truck quit running yesterday suddenly and unexpectedly. It sputtered briefly and the motor total quit running. I pulled over and tried to start and it briefly fired but then totally quit. Got towed home. And now testing to see what all to repair..Thinking fuel.
I don't get any codes from the tester with KOEO..just the good to go etc..no codes or the good to go 111..etc. Guess this problem can't be identified without motor running.
My wiring diagram doesn't give me all for my Calif car..I don't see where the relay is but my fuses are all good, and I'm getting voltage when I crank the motor at that inside firewall switch on both its wires(incoming/outgoing)..forget what its called..Inertia Switch?..that will shut off fuel pump during accident or impact etc. And I've read that this switch is upstream of the relay(if I read that post correctly) so guessing it's the pump itself that is bad.
Does that sound right? Should I go ahead and pull the fuel tank etc and replace the pump? Or is there more testing I should do? When I turn the ignition key on..the pump makes zero sound. That's not the way it normally operates. Usually with the key on the fuel pump comes on momentarily and I can hear it. Forget how to drain the fuel tank etc..I don't see a drain plug? I did it once many years ago..but forget how?
View 7 Replies
I have just inherited my recently deceased father's 1992 Ranger with the 2.3 liter engine. He was a Ford Mechanic but got to ill to worry about fixing the Ranger. So, let me begin, the engine dies randomly, (at idle or in gear driving doesn't matter what gear or speed), turning key to off and then to on will allow vehicle to restart every time. No "Check Engine" light has ever lit, I do have an "Antilock" light that comes and goes. The engine codes I keep getting are: 10, 218 and 222.
Code 10 is a computer check code,
Code 218 is "Loss of Ignition Diagnostic Monitor (IDM) signal/left side, and
Code 222 is "Distributorless Ignition System - Loss of right side ignition diagnostic monitor (IDM) signal.
These codes were from my Innova reader. I have read where other similar problems were fixed with a new Crankshaft Position Sensor, replaced mine, no change. Another symptom I just noticed is my temp gauge stays near the cool end when it should be higher.
View 14 Replies
I have a 1999 B4000 4.0L with 160K miles on it. Bought the truck new. Up until about a year ago it ran perfect but has developed an idle, stalling and occassional jerky ride problem. It occurs at any temperature, engine hot or cold, A/C clutch on or off and in Park, Drive or Neutral. When you start the engine it will not idle unless you keep your foot on the gas. The idle speed will drop to 200-300 rpm and the engine dies. Sometimes you can barely tap the gas pedal and the rpm will shoot up to normal idle speed (about 900 rpm) and stay there a few seconds then begin to drop again. If the engine is cold it will often die a couple times after starting even with the foot on the gas and then about the 2nd or 3rd time run with your foot on the gas.
At stop signs and red lights you have to keep your foot on the gas to keep it running. If you are approaching a stop sign and take your foot off the gas to coast to a stop and brake, the engine rpm will drop and the engine will die. It always starts fine though. Once you are driving it generally runs just fine at low or high speed. You can generally set the cruise control on the expressway and cruise right on. However, sometimes all of a sudden the truck will start bucking and jumping as if it has a terrible misfire. It usually lasts a few seconds and quits. Often if you step on the gas it quits. Even less occasionally the engine will begin to slow as if it is starved for fuel and slow down. You can press the pedal to the floor and it sputters a bit then picks up and runs fine.
I have read about all the threads in this forum and others and tried some of the suggested fixes but it still has the problem. I have tuned it up with new plugs, wires, fuel filter, air filter and PCV valve. Based on some of the forums advice I have replaced the IAC valve, the EGR valve and EGR Pressure Feedback Sensor, and cleaned and inspected the MAF sensor with MAF cleaner. I have checked all my vacuum lines and no leaks there and checked the engine timing which is fine. Fuel rail pressure and engine compression are also fine. Spark plugs show no clues, exhaust is clean and the engine uses virtually no oil. There has been no tear down on the engine like removing the heads, cam, timing gears or any of that and the engine is completely stock.
It shows no codes related to the problem. Two or three months after the problem started I showed a code that indicated an injector problem, traced the problem to a bad injector, replaced the faulty injector and it was fine. That took care of that code but didn't solve the idle problem. In my younger days I was into drag racing and I rebuilt engines, swapped transmissions, etc. and still do my own tune-ups today so I am fairly familiar with auto repair and have most of the tools for testing newer cars but this one stumps me. As a last resort I'm about to take it to the dealer.
View 14 Replies
2000, 2.5L standard transmission. IAC replaced about 2 years ago, DPFE sensor and vacuum hoses replaced early last summer. Truck has been running just fine until I washed it last night. Went to work, and when coming to a stop and pressing in the clutch, engine starts to race without coming back to idle. Had to turn the truck off in order to get the engine from racing. Same thing on the way home. What else can/should I be looking at? I did not open the hood to wash the engine off, so it can't be water from the wash.
View 7 Replies
My surging/running down issue has returned on my '86 2.3l Ranger. I thought it was electrical, when things improved with the new ignition switch, but lately it's hard to get out of 2nd gear before the engine surges then starts to lose power. a poke of the gas pedal starts the who cycle over again. I pulled codes but it's hard to tell what the reader is saying either 33 and 34 or 334. The good thing is all the codes point to the EGR system. Looking for a diagnosis tree to determine if the valve is bad or the sensor is shot? They are both not cheap so I don't want to just throw parts at the problem.
View 14 Replies
My 3.0 with 216k miles has developed a rough idle and it progressively got better with new parts and cleanings. On startup it revs up to 2k then back down to 600. If I let it idle for about 8 or so minutes my Check Engine Light starts flashing. If I drive about for a little bit it stops and is just fine.
While the light is flashing I get codes P1000, P0305, P0306, and P0316. Which are OBDII Monitor Testing Not Complete, Misfire detected in Cyl 5, Misfire detected in Cyl 6 and Engine Misfire Detected on Startup (First 1000 Revolutions) respectively. Any other time the truck runs like a dream. Gets 20 city and 29.5 highway.
I cleaned my Mass Air Flow, replaced my Idle Air Control, SeaFoamed throttle body and vacuum lines, brand new coil pack, new wires, new plugs, new fuel filter, I've only ever run 91 octane, Chevron with Techron goes in at every oil change and B12 every other and I just ran 3 bottles of Lucas fuel injector cleaner.
View 12 Replies
I have a recently purchased 2000 ford ranger 4X4 with approx. 130,000 miles on a 3.0L. When I bought the truck, it was running rough while in gear at idle, after first putting it in gear, and when coming to stops, then it quit running all together. I started by replacing plugs, wires, and ignition module. I finally got it to fire up after that, but instantly noticed the tell tale white smoke from the exhaust. Needless to say, my oil looked like chocolate milk. Rather than having the heads machined and checked, I opted to purchase a new set of cylinder heads from Dover cylinder head.
I got those on this week and she fired right up. After a few oil changes to eliminate the residual coolant from the oil passages, she still starts and runs fine, although the idle is a bit rough while in park. When I place it in gear the idle gets a little rougher. After a quick trip down the road, I'm noticing a pretty solid shudder when coming to a stop, almost like it's stuck in 2nd gear, but I can't really tell for sure. Seems to shift fine going up through the gears, but coming down is when the issue is.
I believe I'm dealing with two separate issues, one being the rough idle upon startup that doesn't seem to go away, and two being the rougher idle upon stopping. I've read everything from EGR valve, idle air control valve, low fuel pressure, and a laundry list of other things, and I just don't want to start throwing money away chasing my tail.
View 4 Replies
I've shipped my R32 back to the UK, the combination of cold and damp weather has taken it's toll on my car. I started it up Saturday and left it ticking over to allow it to warm up before driving it. The car is used to Houston heat, so a few minutes running will allow the oil to warm a little as the weather here is around 40F at the moment. The car ran for 5 or so minutes, then stalled.
The car starts to about 3 seconds, then dies. I have checked VAGCOM, the only fault is a steering wheel sensor (?). It has a full belly of Shell 99 RON fuel and was serviced just before if left the USA in October.
I have had it towed to the local dealer for repair. I have tried disconnecting the battery for 30 mins to reset the car, it didn't make any difference. I have also tried another key in case it's s sync problem.
View 10 Replies
This is concerning my little brothers truck. It is a 2008 4.2 liter with around 55,000 miles on it.
He drove it to work today, and called me this afternoon saying that the truck starts then dies a few seconds later, and the battery light illuminates. He and a coworker checked the battery and connections....cleaned off corrosion on terminals, battery reads 12.xx volts without a load on it, it is the original though.
As of right now he is changing the fuel filter which hasn't been done yet. I also know of issues with the fuel pump driver module. I remember checking the one on my 2005 back when I owned it. As I recall it causes a no start condition, but would it cause a start then stop condition like this? He will check this when he is done with the filter.
Anything else that we can check in a parking lot to try and at least get it home?
View 6 Replies
Simple enough the truck starts then after about 30 seconds it bogs down and dies. I am getting these codes.
705 Transmission Range Sensor Out of Position
708 Transmission Range Sensor Circuit High Input
720 Output Speed Sensor Insufficient Input
743 Torque Converter Clutch Circuit
745 Pressure Control Solenoid Malfunction
1747 Electronic Pressure Control Solenoid A- Short Circuit
Sounds to me like the converter it locked up. What do you think? Its a 5.4L
View 3 Replies
So i start my car and it starts easy but after a few seconds it dies. I can get it to keep running by changing the fuel mixture but then it has no throttle and it will die if i try to use the throttle. It is 1985 VW Jetta engine in a 1981 Scirocco
View 2 Replies
