Ford Ranger / B-Series :: Clutch Pedal Will Not Go To The Floor And Therefore Truck Won't Start
Aug 29, 2015
Installed a new clutch and slave today. Kept the same master cylinder.
The problem I am having is that the clutch pedal will not go to the floor, and therefore the truck won't start. The slave is moving back and forth roughly 3/8 inch, maybe more. I am pretty confident that there is no air in the system.
If I loosen the pressure plate a little, the clutch will go to the floor. But tighten it back up, and it again only goes down about 75%. This is a late '95 so it has the self adjusting clutch. I did get the correct kit for it, as well as slave. It's like the self adjusting part is too far adjusted and won't let my slave travel as far as needed.
In troubleshooting, I did notice that I failed to get the dowels in the flywheel aligned in the pressure plate. I am old school and not used to dowels in the flywheel! The dowels are not hitting anything and are not preventing the pressure plate from seating on the flywheel. But it is something I'm going to fix if I have to pull the trans again.
For reference, I replaced the clutch because the slave cylinder was hanging up and preventing the clutch from getting fully released. Aka clutch slipping.
View 6 Replies
Advertisement
1997 Ford Ranger w/manual 5 speed tranny
A few weeks back my clutch pedal seemed a bit softer than usual one day. Still it worked fine... no problems shifting. Today after a short ride it went almost to the floor before disengaging. Now I cannot get it in gear without grinding.
So cold out I'm not sure I want to tackle this right now, what to look for and where?
View 14 Replies
My buddy called and said his clutch pedal went to the floor on his 04 4.0 ranger. Said no fluid leaks or anything, so I suspect the slave cylinder went. He said the slave is on the inside of the trans and you gotta pull the trans to do the slave, so might as well do the clutch too. How hard is it to replace both these on this truck? I've done it on a 94 cummins, so the trans should be a lot lighter. just wondering how bad of a job it is to do?
View 2 Replies
So I just had my entire clutch replaced while another repair was taking place. What I've noticed is the "clutch engagement" has changed. Where as I would have the clutch start to engage/disengage at the 1/2 way point on the pedal travel is now the last 1/4 of the pedal. Is this a "normal reaction to a new clutch that just takes getting used to or is there an adjustment I can fine turn it with? Do I just have to wait for it to "break in"? When I replaced the clutch on my dearly departed 94 ranger, I replaced the bearings & disc only reusing the pressure plate and did not have this issue.
View 3 Replies
1999 ranger 3.0, 5 speed stick. I was backing out of my driveway but there was a car coming so i pushed in the clutch and waited for the car to pass, when I let clutch pedal up off floor i heard a grinding noise, a little while latter did the same thing in first. Is this a first and reverse gear scyronizer or something else. What causes this and how to fix it ?
View 10 Replies
acts like abs sensors could be bad. but the brake pedal goes almost to the floor, after it does it's pulsating. But the abs light does not come on. I already changed brake booster, no change!
View 5 Replies
I've had my truck a few years now but for 2 it was basically parked. When I started trying to use it again I am having issues with the clutch now. When it is cold everything is fine, but on hot days or after I have been driving for a while It will lock the pedal up and will not let me dis-engage the clutch at all. Sometimes when it does eventually let the pedal down it will go to the floor and stay there for a few seconds until it slaps back up and engages slamming the truck into gear.
I have yet to try much. I'm not good at working on anything other than stereos in cars but I am willing to try. My thought is some water got into the system and is boiling in the lines but I am not sure. Places to start? I really need my truck going and the couple places I've taken it dont even want to try it seems like.
View 2 Replies
This is unusual. After driving into town for new tires, the clutch pedal was hard and I could not depress it after the tire tech parked the truck. It did finally depress with a pop, though the pedal functioned there after the clutch did not function properly.
At times it seemed to be ok at other times it seemed weak. I stopped by Autozone and checked the fluid, seemed low and I added some. Continued home not completely confident that I would make it. Had to make one stop along the way.
Once again the clutch pedal was stuck at the top and would not depress. I finally slid the safety switch up the clutch shaft to start the truck, when the engine started the pedal depressed. I was able to continue home but the clutch is not functioning properly.
View 2 Replies
I have a 88 ranger supercab 2.9l 4x4 with the fm146 trans and recently I have had a problem with my clutch master cylinder rod falling off my clutch pedal. I bought the new bushing and put it on and it was fine until yesterday. It wants to keep coming off. Is there a clip of some sort to hold it on or no. I looked at a few at the salvage yard and they did not have a clip just the bushing. So what do I do?
View 1 Replies
I'm looking for a part number for the rubber stop that mounts behind the clutch pedal on the firewall for a 2001 Ford Ranger 4cyl 2.3L 5spd Manual. Can't seem to find it on the web. It looks like it snaps/presses into a mounting hole behind the pedal. The original one decided to disintegrate and now I get a nice knocking noise when ever the pedal is depressed.
View 7 Replies
I replaced the clutch, slave, flywheel and pilot bearing. Now it sounds like gravel bouncing around under the truck.
Everything works beautifully, but there is horrible noise especially at idle. If push the clutch it will quiet a little. If I change the rpm it will get worse then quiet out then get loud again, there is a sweet spot.
What the heck did I do wrong. It's a horrible gravelly grinding sound.
View 7 Replies
I have a 1994 Ford Ranger Supercab with 180,000 miles, 4.0ltr 6cyl and it is in relatively good condition. When I bought the truck the check engine light was on. The previous owner said that it was something in the gas tank that has gone bad but it was not a big deal and the truck could be driven with no problems.
My mechanics have tried several times to read the error code but their diagnostic tool won't tell them what is wrong.
I have noticed over the past few days that when I am slowing down and riding the clutch (I was making a u-turn this morning) that the truck will shut off. It starts right back up but it keeps happening.
I have been considering replacing the IAC, new spark plugs, rotor and wires and fuel filter but I am not 100% this will fix my problem. I am NOT a mechanic but know plenty of them so it will be a situation where I buy the parts and a buddy puts them in.
View 9 Replies
Started up my truck today, accel pedal didn't want to move, after giving it some more force it eventually became "unstuck". Now, the real issue I'm having is from a dead stop, in 1st gear, as I'm letting out the clutch the truck boggs down as if I'm not trying to accelerate. I'm giving it as much as I normally would as I'm letting out the clutch but the motor will either die or take a couple seconds before it starts to go. Once I'm moving I don't notice any problems clutching through gears. The check engine light IS on now, however I don't have any diagnostic gear or really any tools for that matter. 1998 2.4L 5-speed...
View 2 Replies
I have an '89 Ranger, Extended Cab, 2x4, 2.3l, Manual transmission with 255,000 on the odometer. I've owned it since 1990 and as far as I can remember it has either never had a clutch or only had one. I realize it's past due.
Everything has been fine up until this morning. 10 minutes after leaving the driveway this morning going a steady 55mph, no incline, it sounded almost as if I hit a deer. The truck jerked real hard, I put it back into 5th, and limped to my destination. Keep in mind for the next 30 or so miles there was absolutely no clutch slippage.
Here's the symptoms: No slippage, won't go into gears (I have to match rev's and shift without clutch, I drive a big rig and do this daily), when I do get it in 1st at a stop sign it wants to lurch with clutch all the way pushed down, I still have a great clutch pedal, and the most interesting thing to me is it sounds like something is being tossed around in my bell housing.
I'm almost 100% certain it's the clutch, however, I just wanted to come on here and report I have no slippage and it sounds like something being tossed around in the bell housing area. Is it possible a piece of the clutch could have "broke" off and that was what that huge jerk at 55 mph was? Approx. how much would a shop charge to put a clutch in on this model? I live in a rural area where prices are not inflated.
View 9 Replies
I have a 95 Ranger with the 2.3L and it is a five speed. I am having a starting issue. I have replaced the ignition switch, clutch position switch, starter relay and had the starter tested. The truck will not start with the key. I can jump across the relay and it starts fine but will not even click with the key.
View 3 Replies
I had my battery out for quite some time. When I put in a brand new battery my key was not recognized and my truck will not start.
View 3 Replies
I have a 2002 Ford Ranger, and it wont start at all. Ive replaced the starter, had the battery checked. Not the battery, took starter out, had it checked too, its not the starter either. Someone said it maybe a fuse? This is totally frustrating, and I need to get it figured and fixed asap. Its been going on for weeks., I had it fixed and then it just stopped. It wont even take a jump anymore.
View 4 Replies
This has happened 4 times now over 2 weeks. The engine will turn over but will not start till I press the gas pedal. I have to keep the engine running for a few seconds by hold the gas pedal steady.After it's running you can cut the engine off and it will start right back up.
View 9 Replies
I have a 96 ranger 4.0L shift lever was very sloppy and one of the torq bolt fell on the floor I used loc tite and tightened them up with no problem put everything back together and now it wont start. I think I checked everything even replaced the neutral safety switch, adjusted the tranny cable, checked fuses and switched around the relays maybe an ignition switch? I am running out of stuff to troubleshoot.
View 13 Replies
My 03 Ranger 4.0L has become a mystery that has baffled every one I know. Everything was fine and I ran home to something from my house was in there maybe 10 minutes came out and the truck wouldn't start. it doesn't even crank over. out of the clear blue. I had a friend who works for a garage check it and he thinks timing chain. Since then I have been told it wouldn't just fall off sitting there with no indication at all there was a problem.
Thought maybe PATS system. Its in order. Put in on a computer from auto-zone and it shows a check engine light but the reading is there is no codes in the computer on file. I am at a loss. Its been months and I really cant afford to take it to a garage right now. Its the strangest thing ever no crank, no stalling just nothing I hit the switch it lights up like its ready to start and nada.
View 3 Replies
Removing fuel injectors-coolant contamination.. How is this done? I need to see if they are any good-or clean/replace them-after I accidentally left the clip off the hose running out of the thermostat housing when I drained my coolant last week and the first time I drove, coolant leaked onto the top of the engine/manifold depressions, getting onto and into the fuel injectors.
I tried to clean it up as much as possible the first time(finally got it going) but still a few days later the truck at times cranks but does not start-hot or cold. I assume my idiocy is the cause or maybe it is just coincidence of something else? From what I read from my symptoms it could also be the fuel pump relay, pressure regulator, coolant temp sensor, crank sensor.. among other things. My fuel pump is 1.5 years old, so hopefully that isnt it. Have the injectors possibly been contaminated to where I should just replace them?
View 14 Replies
