1999 ranger 3.0. Check engine light popped up showing P1000 and P0401 codes. I think the p1000 is a system readiness test. Not sure why that came up and the 401 is exhaust gas problem. I put on a new autozone DPFE a few months ago..
View 5 RepliesIve got a question for all you code readers out there. My dreaded check engine light has been on for about a month. I bought a code reader recently and checked it out. Two codes come up; PO401 and PO446. What these mean. My book says "Exhaust Gas Recirc. Flow Insufficient Detected" and " Evaporative Emission Control System Vent Control Circuit Malfunction". Which sensors, location on vehicle, etc..... this is a 97 5.4L Expedition.
View 9 RepliesI have 2007 ES350. I was driving then check engine light and VSC popped on. I went to autozone then they said p0776 & P0746. The car is still driveable. I can still drive it on the expressway. The shifting from 1-3 isn't smooth. I'm going to take it to a transmission shop.
View 3 RepliesI have a 2001 Chevrolet Prizm with check engine light showing PO420 and PO446 codes, what could be the problem?
View 1 RepliesDriving car today and the engine light came on, so before going home I stopped at local garage and had it checked. this is what they got- first code P1445, second code P1000. Car is a 2012 Hyundai Accent automatic hatchback with approx. 40,000 km. (25,000 miles) bought in May of 2012.
View 5 RepliesI own a 2001 BMW 325i. I bought it in 2011, it was in excellent condition, except for a small oil leak. I fixed the leak and then everything started happening. I've replaced so many things in this car that I've actually put more in to it then what I paid for it. This last issue was a rough idle and the scanner was showing me the code for a misfire. I took it in to the mechanic, he found that it was the first injector, replaced it, the night I picked it up it was still doing the same thing...engine light popped on. I brought it back the next day, they kept it for over a week, running test after test, finally they did an internal survey and found that the first cylinder is damaged and the shop has condemned the engine. My question is this: Is there no way to repair a cylinder? How or why does this happen and how much longer can I drive the car before it craps out on me. So far, it is rough when it's cold..but once it warms up it rides just fine. Engine light comes on and then goes off.
View 2 RepliesI have a 1997 Ford Ranger and my Check Engine Light came on a while back. So I eventually bought a scan tool and I'm only getting one code which is P1443. I've looked at both my Chilton and Haynes Manuals, my Ranger manual itself which is pretty useless for this problem, and I've been searching the internet like crazy.
From the threads I have read here it doesn't seem like a hard problem to fix yourself, and it seems like if you take it in anywhere they will charge you an arm and a leg to work on the EVAP system but it's an affordable do it yourself project.
I just don't know where to begin though, I see people talking about buying the complete set with hoses and the canister and sensor all together but I can't find all these parts. Where do I begin to repair the EVAP system?
Ive got a '94 ranger with the 8 plugs and more often than not while driving and sometimes when it first starts, the cel comes on and immediately I notice a lil rough running and lack of power. Also my milage has dropped since this has started. Plugs, wires, o2 sensors, not to familiar with my gas saver. I love it cause I can just get in it and go. With twice the fuel milage as my bi truck!
View 14 RepliesSo i have a 2000 ford ranger 2wd 4cyl .190k miles. My issue is the motor has a very rough/shaking idle,abs light on,and check engine light on.it also continues to blow fuses to the tail lights and dash, haha
Ive had it since it was at 40k and has been a great truck,although lately i have really neglected it.ive changed the spark plugs and new wires new timing chain. I would d love to start trouble shooting some of this stuff this weekend if the weather holds up.
Im getting an intermittent stumble with a check engine light. I have a 1990 Ranger XLT with a 2.3L 5spd. I pulled the codes 32 41 88. I looked them up but Im not sure what to check next. I have done much searching on several sites but havent found much. OBD-1 eludes me.
32(R)EVP - EGR not responding properly during test - EVP
41System Indicates Lean
88 Loss Of Dual Plug Input Control c ..
What does it all mean??? What would you check next?
My check engine light has come on on my 2003 Ranger 2.3L 4V equipped Ranger. I have a Stinger code reader which shows a trouble code P2004. I havn't been able to find out what this code means.
View 14 Replies1990 ford ranger.. I just bought this truck, check engine light stays on.. What can I do to find out what's the problem?
View 3 RepliesI have a 94 Ranger 4x4 with a 4.0 liter engine. The check engine light is on when cold and then after warms up, has trouble starting, seems to flood. When it does crank, rpms go wildly high to over 2,000. I feel it is the Mass Air Sensor but not sure as my mechanic does not have the equipment to read the codes.
View 1 RepliesMy 2000 ranger with the 3.0 is only getting around 10 or 11 mpg. It's got a check engine light on but the scanner just says lean condition. The truck also has a rough idle. I've replaced the fuel pressure regulator and fuel filter.
View 14 RepliesI just bought a 1998 ford ranger with 228000 miles on it seems to run fine has the 2.5 4 cylinder with auto trans. Check engine light is on and code is a PO171. I've cleaned the mass air flow sensor and fixing to install new fuel filter. what the problem could be?
View 12 RepliesOK, got a check engine light today when I fired up the Ranger. Like I posted previously it is running kind of rough so guess I know why now.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use? Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
I've got a 1992 Ford Ranger 2.3L with about 240,000 miles on it. The check engine light started blinking on and off pretty regularly so I pulled the OBD1 continuous memory codes and came up with this.
327 - EVP/EPT circuit below minimum voltage
328 - EGR closed valve voltage lower than expected
334 - EGR closed valve voltage high
I can't say these codes mean a whole lot to me besides I've got issues with my EGR valve and possibly the EGR valve position sensor. I was thinking I'd start by replacing the EGR valve.
Sometimes the check engine light comes on and truck will not start, the fuel pump runs non-stop.. when check engine light goes off,the fuel pump runs for a few seconds and stops,truck will start.... driving down the road check engine light will come on and truck runs bad.... 1993 ford ranger .....
View 1 RepliesWhat this code means. What can I do to fix this problem.
1999 ford ranger xlt ext cab...
My check engine light came on the other morning after a rain storm. I took it to Auto Zone and they put their reader on it and come up with P1633 code. (Keep alive memory (KAM) voltage low).
The next morning the light was off. Couple days later it rained again and the engine light came back. Took it back to Auto Zone and checked it again to make sure it was the same code.
Seems like something might be getting wet unless its just a coincidence that it was raining each time the light came on.
My 3.0 with 216k miles has developed a rough idle and it progressively got better with new parts and cleanings. On startup it revs up to 2k then back down to 600. If I let it idle for about 8 or so minutes my Check Engine Light starts flashing. If I drive about for a little bit it stops and is just fine.
While the light is flashing I get codes P1000, P0305, P0306, and P0316. Which are OBDII Monitor Testing Not Complete, Misfire detected in Cyl 5, Misfire detected in Cyl 6 and Engine Misfire Detected on Startup (First 1000 Revolutions) respectively. Any other time the truck runs like a dream. Gets 20 city and 29.5 highway.
I cleaned my Mass Air Flow, replaced my Idle Air Control, SeaFoamed throttle body and vacuum lines, brand new coil pack, new wires, new plugs, new fuel filter, I've only ever run 91 octane, Chevron with Techron goes in at every oil change and B12 every other and I just ran 3 bottles of Lucas fuel injector cleaner.