Ford Ranger / B-Series :: Burning Oil / Coolant In Cylinder 3 On Driver Side
Apr 14, 2015
I have a '90 Bronco II w/ the 2.9L V6 with a head/gasket issue leak. Its burning oil/coolant in #3 cylinder drivers side. I would ask this in the B2 section, but the Ranger section seems to have alot more activity.
I'm wondering what my options are. I'd like to replace the head with a better aftermarket design if possible. I've seen World Products mentioned as a good replacement, but they are no longer making them anymore. Nearest I cant tell, that leaves King and Odessa aka Clearwater heads. On the 'bay Odessa doesn't have the greatest feedback. King looks like a good product, but kinda spendy also. Short of those two, re-man is the only other option.
The casting # on my head doesn't line up either, is the 86TM the better Euro head for the Merkur?
If I keep this engine, w/o doing a 4.0L conversion, I'm tempted to replace both cylinder heads because of the amount of work to tear it down to that point.
This motor has had some valve ticking also, but I've read it can be injectors instead. What should I do? This will only be used as an off highway light trail rig.
View 9 Replies
Advertisement
Is it what it looks like? Why is it there, to pressure bleed the system through it rather than using a modified MC cap?
View 5 Replies
1990 Bronco II, 2.9l, auto, 4x4. Was running just fine. Sitting in Park just idling away. All of a sudden, just starts running real rough, ticking, etc.
Towed it home. This morning, started up OK but still running really rough.
While running, pulled spark plug wires one at a time from the drivers side. Had no effect but could tell the wires were sparking as I held them up to metal.
Turned truck off. Drivers side exhaust manifold COLD, passenger side HOT.
This sounds real bad to me. Am I missing something simple that could cause the drivers side of the engine to not work?
View 4 Replies
I've got an 08' Ranger FX4. Recently I had the drivers-side headlight go out. Today I replaced the light, and while I was there, I decided to check every bulb on the truck. Everything else works, but I noticed the 2 factory "foglights" will not come on. This is a fairly recent development, because I use those lights quite often.
Even thought they don't cast a huge amount of light, here in the Vancouver area, winters are dark & rainy, so I think 4 points of light as opposed to 2 points is a benefit. To activate those lights, you pull on the headlight selector switch. Do those lights have their own dedicated circuit with fuse? Or does this sound like a switch problem?
View 14 Replies
I seem to have a coolant leak somewhere - i changed the oil yesterday and while i was at it i topped off the coolant in the recovery tank to the cold line. Took the truck out for about a half hour then parked it over night. when i came out this morning i found a pretty sizable puddle on the ground, seeming to originate from the drivers side, and when i checked the radiator it was low but the coolant recovery tank was full past the cold line...i let idle today for about a half hour then let it cool down trying to catch it in the act but saw nothing. if i trace the source of the puddle it seems to be coming from the cap area or at least that side of the compartment. would this be the radiator cap itself? allowing coolant to boil over and out but not get sucked back in? Since I've had the truck i have noticed a small, very small, amount of coolant on the ground now and again but this is the first big puddle.
View 1 Replies
I've been having to add a quart of oil between every 3,000 mile oil change. This is a used 2000 2.5L motor now with about 150,000 miles on it and 317,000 on my truck. I notice the oil is coming from somewhere on the side maybe in a few places. I think the oil plug is dripping a little. I'm going to try an OEM Ford plug because I've changed them several times with aftermarket plugs and they never seal right. I thought it might be the oil pan gasket but it doesn't really look wet around the flange all the way around.
Then I checked higher up thinking it maybe the valve cover gasket which has been replaced and it's drive around the cover. I noticed under the power steering pump bracket it's all wet with oil. It's not the power steering, I've never had to add to it. It appears to be in the middle under the intake. I didn't see anything from the pressure switch. It looks like it's mostly around the pcv valve box. Is there a gasket that leaks there? Or anywhere else that is common to leak? I fixed my transmission pan gasket leak which cleared up some of the mess on the bottom. How hard is it to change that pcv valve box? They call it a crankcase vapor separator where the pcv valve goes.
View 10 Replies
One last issue with my 2000 B3000 3.0L. The leak seems to be on the left (passenger) side of the water pump very near where the bottom radiator hose connects to it. I can't find any loose bolts. It does not leak while driving the truck or soon after. It has to sit for several hours or overnight before it shows up. There are usually 3 or 4 wet spots where it drips from the water pump to the frame to the driveway. It is small enough that I only have to fill up my coolant tank every 1 or 2 months. Could this just be a small gasket leak? It's been happening for about a year or so I think. I replaced the radiator about 2 years ago. I've been expecting it to get worse or bust loose and have been checking it very often. I've never seen one not leak while running like this-has me puzzled.
View 6 Replies
Is there something that would make the 3 cylinders on the drivers side of a 1990 2.9l not fire? I have spark to the plugs and pressure/fuel at the schrader valve on the fuel rail. The passenger side cylinders are firing fine and the engine runs (roughly) on these 3 cylinders. Truck was running just fine, then all of a sudden, drivers side is dead. Is there a fuse or something that controls these three fuel injectors?
View 1 Replies
1987 ford ranger loaned it out and they said the hub spins on the driver side but the tire won't engage so it has no 4 wheel drive. Soon as I get it back hopefully today will know more.
View 14 Replies
I'm normally in the bullnose section, but recently started working on my father-in-law's 96 ford ranger. He wanted me to replace the front rotors.
I replaced the passenger side without a hitch, but when I went to replace the driver's side, I noticed the cotter pin and castle nut were missing. A nail was in the cotter pin's place. I backed off the spindle nut and found that the threads were eaten up, as was most of the spindle with various gouges and nicks.
1996 Ford Ranger XLT 2.3 ......
View 11 Replies
I am a new owner of my first truck and it is a 2003 Ford Ranger 3.0L Extended Edge with 138,000 miles on it. I keep getting a chirping noise coming from driver side of truck. It only happens when I have the AC on. I can turn AC to just air and the chirping stops. This only happens when I am driving. If I have my truck parked in drive with the hood up, I go and turn on AC full blast and I hear no chirping. I can see AC compressor turn on a few seconds after I start the truck and it is not cycling on or off every few seconds as some people I have asked told me it should do. AC air is ice cold so I should have enough freon. Now this chirping is not constant like a machine gun going off but just about every 5 seconds or so it would chirp. I have heard of bad camshaft sensors causing chirping but would that happen every few seconds and only when you are driving down the road with the AC on? Now I have noticed when truck has sat for a long time I get belt squeal for a few seconds and it then goes away. I think the squeal goes away when AC compressor starts because I observed this when looking for this random chirp. Any clues?
View 4 Replies
My 89 735il is leaking coolant from under the driver's side bottom of the car. Is this a heater core problem? Temperature gauge displayed hot temp, then coolant started to leak out...
View 14 Replies
When driving down the road, there is a constant "thud thud thud" coming from the front driver's side of my 99 Ranger. I've been looking online for about two hours now, going back and forth to my truck to see if I can figure out the problem. All I've come up with is that it's the sway bar links. they're both disconnected, and I'm going to replace them anyway, but would that cause the constant thudding?
View 3 Replies
Bought a 2002 ranger with a four liter in it. Didn't notice until actually going off-road there is something wrong with the four wheel drive. In 4 high it will drive good for a random distance then a loud bang, pop, comes from what feels like it's the driver front tire. The faster you're moving the worse it is. It's not consistent at all.
Replaced the transfer case shift motor and both CV axles. Still does it. Walked next to the truck while it's moving and the front tires look like something is in a bind and it's causing the bang. Beating my head against the wall at this point.
On a side note it has something wrong with the tranny. Taking off it feels like someone bumped the rear, and after about twenty minutes of driving od light starts blinking and it shifts hard from first to second. Kill it, cures that specific problem just not the takeoff problem. Not sure if this is all related. Pulled the pan and refilled with as much fluid as came out. Which was a dark red. Still having same issues.
View 5 Replies
I noticed that one of my vacuum lines was bad on the driver's side. I've done a lot of reading on the 4WD systems and frankly I'm confused now. My understanding is that when in 2WD the solenoid is open pulling a vacuum on the actuators (IWE) which keeps them disengaged. When you switch to 4WD the shift motor on the transfer case sends power to the front wheels and the solenoid turns off the vacuum which engages the actuators sending power to the wheels. Therefore if there is a vacuum leak the actuators won't disengage properly.
Through my trouble shooting I've determined that I think the solenoid is working properly because I'm getting a vacuum when in 2WD and no vacuum in 4WD. I believe that both actuators are engaged and working properly when in 4WD. However, I must not be getting a vacuum to the driver's side actuator (hub) because the line is totally busted up and can't possibly hold a vacuum. However the passenger side line looks good to me. Does this mean that I've been driving around in "3WD"??? I don't seem to have any problems when in 2WD turning (no tire skip or hop).
View 1 Replies
I have an 03 ranger and my driver side window will not roll down... My pass side rolls down just fine...when I push the down button all I get is a clicking noise out of what seems to be a little black box underneath the driver side dash and I can actually physically feel the clicking along with hearing it... When I push up on the button I get no noise or anything... this might be the motor...the regulator...or the actual switch?
View 1 Replies
So I have a 1990 Ranger XLT 4x4, 2.9 v6. My issue is I am getting a loud constant whistle sound on the drivers side, just in front of the rear tire. It is not from the tire and it is a whistle not a whine. The truck is all stock nothing special. I do not have an exhaust anymore only a cat. Anyways the sound is constant an does not get louder or quieter while moving or in neutral it just stays the same. It just started in the last few days. Also the truck is a Manual.
View 3 Replies
I bought a set of Ranger seats for my 1957 Ford project. My question is the drivers side seat reclining mechanism is broke. I believe the seats are out of an STX or sport model, they have a slide out bolster and power lumbar and side bolsters.
Where to get a replacement mechanism. The mechanism works the handle is busted off. It is from an extra cab so the handle is a two way for the driver and or if anyone in the back wanted to use it. I think they may be from a 1992, only say this because I had one backin the day with these kind of seats.
View 4 Replies
My front driver side brake line broke. It had a typical double flare fitting at the caliper but at the distribution block on the other end it had a flared fitting that would be used on a industrial hydraulic unit. I took it to the NAPA store and they told me to cut the nut off the old line and put it new line and double flare it. I did and it leaks. Do I need a special fitting on the end that goes the distribution block?
View 2 Replies
So I just got done with my first 2 problems of the month with this truck last week. Front end and emissions along with spark plugs. Now, 4 days later this morning, I'm driving the truck trying enjoy the investment, and the AC compressor starts seizing up and burning the clutch. Unrelated but also worth noting, about an hour later the brake pedal gets real soft and the brakes get really sloppy at stopping the truck. The truck also stalled (auto trans) crossing a highway, luckily it was 5am and no traffic was coming.
I'm at $6k invested on a truck with 116,000 miles, and I've only put 6,000 on it. The repairs don't stop, and I've got many more ahead. Like rear suspension, axle, trans, and radiator fluids, and paint, to name a few. Any suggestions on fixing the AC before I drive this truck into a lake?
View 8 Replies
In 4 x4 ( 2000 ford ranger 4.0 ) and drive for a while I can smell gear oil burning off the exhaust looks like it's coming out of the right cv shaft? Is there a seal that goes first That's bad?
View 6 Replies
