The panel goes off and the fan quits blowing. Sometimes it works, cools great, then just cuts off...
1989 Bronco II 2.9 4x4 auto 164k miles... I have been on TRS, BroncoII Corral, and even FSB searching.
This is the first attempt at reaching out because i have found that here at FTE the folks that chime in know their stuff, or know where i can find out for myself.
1988 Bronco II - 2 days ago while driving my check-engine light came on for about 5 seconds, though there were no apparent drivability issues, then went away and did not come back for the remaining 20 or so miles home. Then yesterday while driving to a destination the engine cut out a few times. Gauges and such stayed illuminated but the engine lost power as if it wasn't getting fuel or spark. It occurred randomly over a 3 minute period: 1 second bogging, then 10 seconds powering, 3 bogging, 20 powering, 2 bogging... I depressed the clutch to check if the engine could idle and it stalled. Then I restarted the truck and drove 5 miles home with no issues or check engine light and even driving for a minute at WOT would not make the issue remanifest. I did not drive it today for fear of breaking down and I hope to get this solved before taking it on the road again.
I read the following codes:
KOEO: 11 (passes)
Continuous Memory: 22: Manifold Absolute Pressure (MAP) or BARO sensor out of range.
KOER: 11 (passes)
The Problem: When I start my Ranger it dies right away, I do this about 10 times or so (worse when it is wet or has rained) then I can finally keep it running, by hitting the gas. Once I get it running it will cut out while driving as well. The idle is normal and if fires properly, I just took it in to the shop (non-dealer) and they said it fires normal and has normal fuel pressure, and the their computer returned no error codes. Their sugestion was replace the throttle position sensor. Do you all think this part could be the cause and where is the this sensor and is it hard to replace?
View 12 RepliesI've been replacing my steering components over the past month and have fixed all the previous issues other than this one that's got me stumped. After I make a hard left the steering will pull left (very hard) until I either turn the wheel right or hit a bump. Sometimes when going immediately from a left turn to a right turn (or vice versa) I can actually feel a slight pop as it starts to pull.
The order of repairs thus far has been: new power steering pump, new inner & outer tie rod ends, professional alignment, new steering box with both lines. The shop and I both agree the ball joints are good. I've jacked my truck up by the frame and removed the wheels to check for steering/suspension play but have not been able to find any. 180k miles on the chasis.
Still cant seem to fix this 87 ranger 2.9... NEW fuel reg, fuel press reg, rebuilt computer.cold it will start and run fine.then it will shut down with in 5 to 18 miles then you cant hear the front or rear pumps at all!. Let it sit over night and your off again.. Can't get any codes.. Can a pump over heat and shut both off??
View 14 RepliesI have a 2006 2.3 ranger motor runs fine at idle and as I ride down the road the motor just cuts off. If I pump gas it will take off again and in 3 miles it will do it again. After 20 miles running good it will cut off again. Replaced coil pack, fuel pump, Cam sensor, Idle control sensor! What else could be causing this?
View 3 RepliesDriving a 2008 Ranger XLT 3.0. Starts runs and drives fine, how ever it seems to have a tinny ruff idle.
What I noticed is when in park or neutral when I idle it up @ 3000 RPMs it seems like it runs on 3 cylinders and sort of cuts in and out very quickly. Is this a protection thing on the ranger.
Running on the road it kicks down and runs thru all the gears normally from idle all the way up to 5000 RPMs. Just would like to make sure this is normal.
Here's my problem I have a 02 ranger 3.0 with some problems and I need to bounce it off some one with knowledge.
1. starting and normal running fine / ok .
2. In drive at 2200 rpm t0 2800 rpm the engine is sluggish and at night the head lights dim about 30%
3. Sometimes the battery light will turn on during this problem.
4. The only code is for a air leak fuel / evap system .
5. Above 4200 -4500 rpm the engine staggers or cuts out.
Parts changed coil: / ECM, Fuel pump and filter, plugs & wires several relays and alternator.
Inspection: Checked most ground and common grounds, looked for damaged, cut worn an burnt wires or worn harness plug / connectors .
I have a 99 Ranger 4.0 4x4. When driving on a hill, the truck cuts back and looses power. I can press the pedal and go into passing gear and it will pick up speed but that is the only way the speed will increase and not slow down. The truck jerks when this happens.
Things I have tried:
Replace all plugs and wires
Replaced Coil Pack
Replaced Mass Air Flow sensor
Replaced O2 sensor
Replaced throttle cable
Took truck out of overdrive
Changed to better grade of gas
Changed oil
I had Cat. Converter checked
There are no codes showing. Truck may drive OK on one trip but act up on the return. It seems to use a lot more gas when it is acting up. I now have run out of options that I know about.
I have an 87 ranger that has started having problems over the last week or so. I had a similar problem a year or so ago. I put a new fuel pressure regulator on and it fixed it. So it started acting up again so I got another regulator and it didn't work at all. It won't idle at all without dying. The motor revs up then cuts out completely and dies. It's like I'm repeatedly pressing the gas pedal when I do get it to idle but I'm not touching it at all. It runs fairly well on the road until I let off the gas then it goes to shaking and jumping up and down till I get back on the gas.
A guy told me to unplug a little cigarette pack shaped plastic box and see if it changed anything. I think he called it a map sensor? But that didn't do anything. I was thinking maybe the fuel filter was clogged up but I don't really know. It is fuel injected 2.9 4x4 regular cab. About 110000 miles. Not sure if filter has ever been changed. It doesn't smoke or smell like gas so I'm thinking it's starving for fuel.
I have an F-150 with a 5.4L EFI and A/T. For the past two days while driving along the engine just cuts out. There is no chugging or sputtering. It just dies. When it happens, I place the trans in Neutral while still rolling along and it starts right up.
I had suspected it might have been a bad eec relay and connector that I had trouble with in the past, but I changed that all yesterday and the problem happened again today.
Our Ranger, 2002, 4 cyl. 2.3 5 speed is shutting down while driving. This has happened twice very recently. Both times on interstate at highway speed. First it loses power then completely shuts down. After stopping, turning key "off" it restarts and runs fine. It does take a longer time to crank before starting.
It is not throwing any codes and the CE is not coming on. I suspect the fuel pump is shutting down. Seems like fuel pressure loss is reason for loss of power? Then extended cranking to restart is the initial build up? What else could it be? If not the pump itself, is there something that would take away power from the pump then get reset?
1994 FORD RANGER stalls while driving - differant speeds ...differant miles ...no rhyme or reason to it - cranks right back up ...can even pop clutch and cut it back on. Already replaced Ignition Start Module - Dpes sensor - temp sensor - and scan shows all codes are clear and truck passes. We are clueless to whats causing this. 4 cyl 2.1
View 12 RepliesToday my 2001 ford range edge starting running funny. When in park it idles around 3k rpm and then when driving it feels like it wont shift past 2nd because it is around 4k rpm around 50mph and I'm afraid to go to any higher speed for fear of damaging the engine. I'm currently at work so im unable to really get under the hood atm.
View 2 RepliesI have a 1985 ranger 2.3l efi and it bogs and dies while while driving, it can sit and idle all day long but when you go to drive it, it works great for 3-4 minutes then out of nowhere starts bogging sometimes I can keep it going a little longer but in the end the truck always dies . I know I'm loosing fuel pressure , I hooked a gauge up to it and drive it down the road when the truck died it showed 10 psi , from here I'm lost . It has a new fuel pump in the tank and I can hear the other one running when I click the key on , Also two new fuel filters .
View 3 RepliesRecently, today in my 87 Ranger suddenly the engine dies and all electronics in the cab fail.
I noticed under the hood that the fusible link connected to the battery and an orange and black wire was smoking. Tracing this line i found that it leads to the ignition switch, as well as some other places.
There is another fusible link and the junction between the yellow ignition wire and the orange and black wire from the battery. This fusible link also was failed.
I'm planning on replacing the fusible links tomorrow but in case that does not fix it, where to look next.
The problem only occurs when the key is in the ON position. I'm thinking maybe I could do some tests with a multimeter on the ignition switch but am not sure of the details of what I should test for.
Summary: Fusible Links C, and E burn out when the ignition is in the ON position.
I've been dealing with this for 2 years now and its going to snap my axle shaft one of these days. I am scared to take it out in a snow storm because the truck will clunk and then release. Its a split second thing but its enough to notice and make me worry a lot. I cant figure out why and ive done the plugs and wires but that didn't solve the problem. It only happens when its snowing or when I drive though a gust of wind that has stired up some snow. I know it must be something electrical because it only happens when there its cold and wet and not all the time. In the rain it does not matter but when it snows i just wont go out at all. The truck is a 2003 4.0 4x4 with a manual. Not a function of the 4 wheel drive it happened in 2wd as well.
View 14 RepliesMy 1999 ford ranger, when started, shakes and then while i am driving. my check engine light is on and reads a #3 cylinder misfire. I have taken it somewhere to get it checked out and they can't figure out what is wrong with it. this problem only happens 50% of the time. I don't know what to do. Also just got a tune up.
View 14 RepliesMy 2004 Ford Ranger has 220,000 miles, runs great, and when I bought it this summer the 4 wheel drive worked great. Starting when the weather got cold when I engage the 4 wheel drive (no lockouts electronic engagement). I will drive and it will kick in and out of 4 wheel drive when it starts to slip or I have to accelerate.
When the 4 wheel drive kicks out I will let off the gas then it will engage again on its own, but will slip out again when on ice or I start to slip. When the 4 wheel drive engages it does NOT make any strange sounds, no clunking or nothing, it engages smoothly, and disengages properly.
What it could be? a connection? Any way to fix or diagnose the problem? I have been told that it probably is not the transfer case, because if it were it would not engage or stay in 4 wheel drive at all.
Background- 2000 Ranger, 3.0L 2WD 170,000mi. This truck is not my daily driver, i try to drive it once a week.
I've never had this issue before... I drove all over town yesterday; multiple stops, no issue. Today i go to do the same thing and upon accelerating out of the driveway i lose all power for about 3 seconds. I get power back for about 3 seconds then lose it again. This continues for as longs as i'm driving. Also, no CEL. I go back to the house to look things over, can't find anything staring me in the face really.
Truck idles fine and the issue is not present when i run up the RPMs in park. I've been reading some other threads about similar issues and most replies begin with checking the regular maintenance stuff i.e. TB, MAF, IACV, pcv, etc. It seems like a complete loss of fuel or spark...but only when in gear with constant throttle???
I have just inherited my recently deceased father's 1992 Ranger with the 2.3 liter engine. He was a Ford Mechanic but got to ill to worry about fixing the Ranger. So, let me begin, the engine dies randomly, (at idle or in gear driving doesn't matter what gear or speed), turning key to off and then to on will allow vehicle to restart every time. No "Check Engine" light has ever lit, I do have an "Antilock" light that comes and goes. The engine codes I keep getting are: 10, 218 and 222.
Code 10 is a computer check code,
Code 218 is "Loss of Ignition Diagnostic Monitor (IDM) signal/left side, and
Code 222 is "Distributorless Ignition System - Loss of right side ignition diagnostic monitor (IDM) signal.
These codes were from my Innova reader. I have read where other similar problems were fixed with a new Crankshaft Position Sensor, replaced mine, no change. Another symptom I just noticed is my temp gauge stays near the cool end when it should be higher.