Ford Ranger / B-Series :: Brakes Cut Out When Pulling Up To Stop Lights Toward The End And ABS Kicks On
Oct 25, 2012
I recently changed the front pads and rotors on my 2002 Ford Ranger 2wd and I'm having some troubles now. Occasionally when I'm pulling up to stop lights toward the end of my braking i can feel them cut out and the ABS kicks on. It's a very intermittent problem, and it only happens at low speeds. When I try to induce the fault it never happens, it only seems to after an extended period of braking going less than 10 mph. I'm very confused, and I was thinking about changing out my calipers unless know what might be happening.
View 1 Replies
Advertisement
That's the best way I can describe part my latest problem. If I'm stopped at a light, a lot of the time it almost feels like it wants to stall when I first pull out. Then, it seems like it is shifting funny at certain speeds like the transmission can't decide what gear it wants to be in. Tends to do that about mid acceleration (don't have an rpm gauge to look at). At idle it seems to run fine. BTW, engine also runs rough with the ac on.
View 12 Replies
All I did was take wheel off to tap a stud and I saw the inboard pad shim came off. So I removed the shim and reinstalled everything and the wheel is severely pulling to the right. Yesterday I took the caliper off but did not take off hose, cleaned slide pins and lubricated with anti seize. Still pulling to right bad. Don't hear any squealing or grinding. But pass side wheel is definitely hotter than drivers side. One mechanic said he thinks it would be a bad hose before replacing caliper. What could it be?
View 8 Replies
When I turn the control to heat the AC compressor kicks in. If turned to vent it does not kick in. Was this just a design flaw.
View 3 Replies
I have a 2000 ford ranger 2.5 automatic. runs fine except when stopping at lights and intersections it stalls. I have changed the MAF, TPS and hasn't made a difference.Truck only has 64,000 miles. What to look at next. no codes...
View 14 Replies
My supercab 2WD has about 100,000 miles on it. When I hit the brakes, the ABS kicks in at low speed (less than 10 mph) even though the tires are not slipping.
View 1 Replies
I was pulling out of a parking lot making a sharp turn when all the sudden I lost my power steering. I have a '94 Ford Ranger manual transmission. It didn't make any sounds. I was going to try to keep adding power steering fluid to it and try to get it home to my mechanic in my hometown - but it drips constant liquid when I drive it down the street (you can see drips) so I don't think that's possible. I've read a lot on here about gear boxes failing, but would this cause it to leak even if the truck wasn't running? (the puddle builds quickly when its just sitting there, engine off). I took it to a mechanic (I don't have tools), and they said they can't say anything for sure until they look around, it could be seals or a new gear box.
View 2 Replies
2003 ranger xlt 4wd electrical - My radio lights up when driving lights are on but no clock display or anything else. My cigarette lighter and aux power outlet do not work and mym 4wd does not work. when i try to change from 2wd to 4wd no lights come on in the dash. I have checked all fuses and they are good. What to check next?
View 4 Replies
My brake lights will not work but all other lights do, bulbs and fuse have been replaced.
View 2 Replies
I had to replace the tie rods in my mazda b2300 and the mechanic also replaced the brake pads.
Now when I drive, I can hear the pump for the brake fluid going on and off when I'm not even using the brakes and the ABS goes on a lot too.
He tried resetting the computer by unplugging the battery for a bit but it's still doing it.
View 2 Replies
Little back story, truck sat up for 2 years. Had 1/2 tank of gas in it that time. I had to do a complete motor swap. I been driving for past couple of days. Had it stall on me while I was waiting on wife to come out of store. Thought it was just bad gas. Today I was heading to town and had to slam on brakes and it started to stall again. It shut off. I cranked it back up and it runs fine till I start slowing down. then it wants to die.
I can keep my foot on gas petal and little and it will stay running. I got to where I was heading and put it in park and it idled fine for a few seconds and then I could hear a whine from the fuel tank. Sounds like the fuel was having a hard time, like it was fighting the pressure build.
Thing is It cranks right back up and drives fine as long as I dont come to quick stop or set idling for a few seconds. I can hear the pump straining, so I am assuming that when I keep my foot on gas a little the pressure is staying lower and not as much is being bypassed and the pump is fine. I think the pump is on its way out but wanted to hear what yall think.
I do have a brand new IAC valve that I bought and did not get a chance to use on the blown motor.
View 10 Replies
I tried to explain this to a garage in January with no luck. When it is raining I hit my brakes and my truck jerks like whiplash. Softly hitting brakes doesn't do it, normally hitting them does it (only in the rain), I had some welding done after I went to the garage.... They fixed the front passenger side now it feels like it is under me and it is now doing it when I brake in reverse too... I bought it October 2012 and it was safety inspected until October 2014. Trying to decide if it is worth keeping. I want to keep it but when I go to a garage they see dollar signs. It only acts up when it's raining. And I had the welding done in January and it was fine, until I got new tires last week.
View 12 Replies
Received the truck, 1989 Ranger XLT long bed single cab from my mom. It had been used by my younger brothers for some years, and then sat at mom's for a couple years.
It needed new front brakes badly, so replaced rotors, and pads. No unexpected problems there.
Looked at replacing the rear. Both adjuster cables were initially broken, so they obviously weren't adjusting, or braking. Replaced with a hardware kit, and shoes, and drums. Its the 9" drums, BTW.
Still not actually braking. I can tell this, when at a stop sign in the winter, with the brake pedal held down, and the backs will still spin, with the tranny in D. Even on gravel or grass, this'll happen.
One shop told me this is because the axle seals are leaking. THey've never leaked badly, and the axle fluid isn't low, by and shade of the imagination. Also, this theory falls apart, when the parking brake works just fine, right? Its just hydraulically that they don't work.
I've since replaced the wheel cylinders, the brake line from the frame to the rear axle, and the master cylinder. No change. Bleeding them doesn't seem to be a problem; i.e. no lack of or little fluid witnessed, it seem fine.
Also have bypassed the RABS valve for about a year or so, and its made no difference. Last fall I pulled the drums off, and manually adjusted them, and it didn't seem much better either.
View 11 Replies
On deceleration with the brakes (not coast to slow) I get a growling. Sometimes a bit worse than others. Seems to get worse coming up to about 20mph from speed. No other time. I was thinking front wheel bearings as the load up from deceleration. But I just jacked it up and could not find anything that felt or sounded wrong. No play or grind or "bad" feelings in either of the fronts. Front end recently rebuilt, new tires too.
View 9 Replies
I have a 2007 ranger and when applying the brakes i get a vibration, I think it may be in the rear of the truck but it is hard to tell.
View 2 Replies
My manual 5 speed 99' 2WD 2.5L Ranger is starting to have some small problems here and there. My main concern is when I start the vehicle sometimes, there is no idle. The vehicle will turn over and if I do not hold the gas pedal down it will die immediately after about 2 seconds.
If I hold the gas down so the RPM's stay up (Around 700 RPM's or so, something just a little above 0 to keep it from dying) after about a minute, sometimes few minutes the idle will kick in and I do not need to hold my foot on the gas pedal to keep the truck from dying.
This is about all I know from the problem besides that it does not matter how long my truck is sitting. For example, my truck was sitting for 5 days and I came home and started it up just fine, but after I drove it a few minutes later and stopped driving, when I went to drive it about an hour later the symptoms came back again.
Also, My brakes are acting a little funny. I went through when I first got the vehicle and bled the brakes, took the front rotors in to auto zone or another shop and had them fixed up, and new brake pads. Sometimes when I first start driving the brakes are extremely sensitive, to the point where I apply a little bit of pressure and my truck will start skidding. This goes away after driving for a little bit though.
View 1 Replies
I just had new shoes, hardware, wheel cylinders, drums, leaf springs, rear shocks, and shackles put on. The brakes were done about 4 or 5 months ago and the springs and shocks just a few weeks ago. The rear brakes were locking up after I had the work done, but I thought they were just too tight. I loosened them a little but it only worked a little.
Now it's starting to lock up pretty much every time I apply the brakes. The ABS kicks on and the rear tires skid. I took the drums off today and didn't see any leakage or anything out of the ordinary. They weren't too tight and I readjusted them but they weren't out of adjustment much if at all. I looked at the Ford symptom chart and it says for brakes that lock up easily there could be sticking or binding components. I didn't see any. Then it says check parking brake components.
Now I see they didn't hook up the equalizer bracket that goes to the front leaf spring hanger when they changed my springs so I assume thats why my parking brake pedal goes to the floor. Then it says check the shoes and linings, which are fine. The last thing it says is to check the fluid control valve. Which I'm guessing is the prop valve.
The only way to check it according to Ford is swap it for a known working valve. One person told me that it could actually be a bad brake booster check valve. Is that possible? Anything else that's common? It's got 272,000 miles on the frame but everything's been changed that typically wears out at least once.
View 9 Replies
I have a 2004 Ranger 4x4, 4.0, auto and have trouble with the back brakes howling, locking up and generally driving me nuts. I've replaced the drums, shoes, cylinders, emergency brake cables and all the hardware. We've bled all 4 numerous times, blown out the lines, looked for leaks and done all we can think of. What am I missing?
View 1 Replies
I have my 1940 Ford pickup on an 86 Ranger chassis. I'm finally to the point where I can drive the truck a little (still not running right) and I'm thinking about upgrading to power brakes. I have used the entire braking system from the Ranger in this build. What's involved in upgrading? Right now, there's a standard Ranger master cylinder hung on the firewall and attached to a Ranger pedal hanger assembly on the other side of the firewall, so I have all Ford parts to interface with. Also, what is the diameter of the booster and how deep is it from front to back and will the upgrade require a different master cylinder?
View 3 Replies
My truck is pulsating when I am coming to a stop, a lot of you all said replace the rotors to which i did and new brakes, shocks. Today I went to get my truck all four wheel alignment done to my truck.. something is not right..
I got my driver tire facing straight, look at the left.. I went back to the alignment shop showed them that, they put it back up there, they called me over and pointed out the machine they use say, it is aligned.. So what is the problem you figure?
To update all I've done to the truck in regards to front end..
rack and pinion
upper control arm
upper lower ball joints
stabilizer inks
rotors (front)
brakes
shocks
When I straighten my left wheel, the right does not look right..
View 4 Replies
1996 F350 PSD 7.3
Front Dana 60 mono beam
4 x 4
Last week I broke my front right caliper. I replaced the caliper, rotor and pads. Now, when I apply the brakes I pull to the left. I took the truck into my repair shop and let them figure it out. They were unable to repair the truck. They replace the master cylinder, all brake lines, calipers on both sides, brake pads, bearings on both wheels, vehicle alignment, tire balancing and tire rotation. The tires are three months old. Prior to last week i did not have any problems braking or steering. Driving at 60kmh the truck goes straight until i gently brake, it will slightly pull left.
View 2 Replies
