What is the likely culprit? No other electrical issues, brake light quit working when brake is depressed, all other lights work including blinkers/running/head. Was going to break out a wiring diagram....
View 7 RepliesI'm having some issues with my 99 ranger. It all started on my way to work one afternoon. Going down the road I started to smell some type of electrical burning smell. I looked at my instrument cluster and seen a trail of smoke come up between the steering wheel and ins cluster from under and gear selector covers. After that the O/D off light started flashing and downshifting hard. My pwr windows and dome light also quit working. Checked fuse #26 and all my fuses before going into work that afternoon, all of them were good and none blown. After shift was over that night going home I needed to use the wipers and they wouldn't work either. Also noticed then that my speedo, odometer and trip odometer not working. I've pulled my dash and steering covers off trying to find or see anything but nothing yet.
View 14 RepliesI have a 2005 F250 with 6.0 Crew cab
Wanted to change out factory bulbs to LED's. The factories were working just fine, just wanted LED's. Broke a couple of center bulb holder's/clamp. Don't really know what they are called. Went to junk yard got a couple of used ones, those worked because when we opened the doors on wrecked trucks Dome lights came on! Got home put them in and NOTHING. No dome, no map lights with LED's. Changed back to factory bulbs and only map lights come on, NO dome lights on front or back and my 3rd brake light quit along with the 2 bed lights. Checked the wiring plug and have power to one wire. What fuses would I need to check or to check where next? Owner's manual is not very specific about which fuse.
I have a 2000 Ford Ranger, 5spd with 3.0 v6. The speedometer will jump around or quit about half the time whenever you push the brake pedal or use the turn signals. I've cleaned all the grounds I can find including taking the battery cables off the clamps and cleaning them, and I had to clean all the fuses (inside box and outside box) because most of them were corroded. It still does it. Occasionally, I'll hear a buzzing/crackling noise like electricity arcing when I use the brakes or the turn signals which sounds like it's coming from the left side of the dashboard.
I took off panels and the fuse box, but I don't see any sign of arcing. Also, the noise only occurs when the truck is actually moving, never when it's sitting still. Also, the engine has a slight flutter at an idle. I hooked up a computer, and the O2 sensors were erratically jumping between rich and lean, so I replaced all of them. It says Insufficient EGR flow detected, so I did put a new EGR valve on and cleared the codes, but it still reads the same. And lastly, the computer refuses to finish either of its diagnostic tests. I've tried the Koeo and the koer tests, and neither will complete.
My odometer has quit working but sometimes will run a few miles. The truck has about 100,000 miles on it and the speedometer works fine.
View 14 RepliesThis morning the passenger side wiper on my 89 Ranger stopped working. I heard a clunk noise and it stopped but driver side still works. What should I check first? I'm guessing a shaft came off but don't know where it is located.
View 14 RepliesMy son has a 99 ranger and the 4 wheel drive quit working. Traced it to the front hubs not getting vacuum. If I jump around the vacuum solenoid(not sure if that's what it's called), the 4 wheel drive works. Looking for a wiring diagram that shows how this is supposed to work electrically?
View 5 RepliesI recently had my fuel gauge stuck on full and at around the same time, my left rear brake light doesn't work. I do have LED brake lights in the rear so I am not sure if that changes anything. I thinking something with a ground or is it possible that these aren't even related.
View 2 RepliesI have a 1997 Mazda b4000 new plugs wires head gasket an I cleaned out the radiator. My question is the truck runs good but my heat quit workin what could it be all fuse look good. Also there is water coming out of my tailpipe with white smoke. Should I be concerned.
View 2 Replies My buddy's 1998 4.0L Ranger caught fire from the dreaded brake switch shorting on the master cylinder. In his defense, he's only owned the truck less than a week and had no clue of the recall. The damage is mainly to the wire harnesses on the driver's side.
Rebuild the wiring. What other years of the Rangers I can pull the wiring harnesses from? Or if the 3.0 harness will work?
1993 Ranger XLT 4.0 AT. Initially replaced ECM for other problems and then noticed Cruise w/n disengage when brake depressed unless pedal is pushed several times and with more pressure. Put in another ECM and have same problem. Have replaced the brake switch and lights come on as they should. When pedal is pushed the vacuum dump valve on the pedal will dump the vacuum to the servo but when you release the brake pedal the cruise control kicks back in and speeds truck back to set speed.
So this tells me that the dump valve is only a fail-safe feature for when pedal is depressed and does not actually deactivate the servo. Everything else with the cruise works fine: On/Off switch, Set/Accelerate, Resume, Coast. How to proceed next? Like where to find speed control module and how to test it? How to check servo to see if it is getting or dropping voltage that will electrically disengage it, etc? Don't want just throw parts at it. The new ECU's that I used came from ECU Exchange in Florida and there still remains the possibility that they are still the problem.
I have a 2008 Ranger Sport 4x4. I noticed yesterday that when I stepped on the brake pedal it felt like nothing was there until I step a little harder then it was like full brake application. The truck only has 63000 on it. Then every once in awhile it would be normal ie very light brake application and slows like it should. Then back to same issue... Any thoughts about this??
View 8 RepliesI have a 2010 Ford ranger sport 4x4, manual, and when backing up at a decent speed, then press the brake to slow up then depress the clutch, the brake pedal pulsates and it feels like something is grinding. It has happened in first once, but I can make it happen in reverse anytime...
View 1 Repliesacts like abs sensors could be bad. but the brake pedal goes almost to the floor, after it does it's pulsating. But the abs light does not come on. I already changed brake booster, no change!
View 5 RepliesSo, a few day i bought an 84 Ranger and even since have not been able to figure out what the hell is wrong with the brakes. I know it's not the brake booster for starters. Because, i went to Auto Zone and picked up a new one and when i took the old one off (before i had put the new one on as well) i tried to see if the brake pedal would now move freely and it won't. It is still very stiff and squeaks when you push it down. i then to get it to return have to pull it up with my foot... What it might be? the WD-40 failed here as well.
View 3 RepliesI have a 1990 4x4 ford Ranger, the little truck was purchased in early 2008 as a work truck but has ended up becoming my main vehicle, it has been a good truck for the most part but know I am having some brake issues, well have been having for some time but they seem to come and go. Usually it happens when I have to hit the brakes hard, the rear brakes lock up, I replaced the master cylinder months ago and thought that fixed it, then a month later it happened again. The last time it happened was friday, the time before that was in march 09'.
I have searched this online and found numerous try this but the original poster never comes back to say if the problem is fixed or what fixed it. My ABS light DOES NOT come on when this happens, it does function properly, it illuminates when the key is turned on then goes off. My parking brake no longer works either but I think that is from me "driving thru" the locked up rear brakes. I plan on replacign both drums and shoes within the next week but would like an option to repair the locking up issue.
Recently the ABS light came on (truck does not have ABS), also speedometer quit working and trans was not shifting right. After a few minutes the problem went away.
View 4 RepliesWas checking fuses for why my 3rd brake light and pedal adjustment switch does not work. Was also looking for a fuse to tie into so that a light in the cab floorboard will stay on when the headlights or marker lights are on... After trying several spots to no avail (finally putting it into the bright headlight fuse). I got the light to work.... But now my ABS light stays on!!! Also 3rd brake still not working...
View 1 RepliesI recently bought a 2006 Ranger with supposedly 110000 miles... I don't think I made a good deal... because I found the stabilizer end link in terrible shape which seems suspicious for this mileage in my personal opinion!? But this isn't the reason I am posting today... I have a serious breaking issue and I couldn't find explanation yet.
My ABS Light is on. When I slowly brake at low speed and when the brake is almost completely depressed... I hear a low humming sound, and the brake pedal seems to momentarily drop back just slightly. This also happens when I'm going down hill and breaking. For the most part, the car breaks, and it's only every 8th or 10th time braking that I experience this issue.
My guess is this is linked to the ABS... but I can't afford expensive service and need to resolve this on my own.
I have a 98 Ranger 2wd reg cab 2.3L 5sp. Recently the airbag warning light was blinking 2-7 which indicates bad lamp in passenger airbag deactivation switch. Since the lamp has no numbers or markings on it, and my repair manual has no schematic on that part, where I can find the ma, wattage or ohm rating of the lamp? Or a part number / source for a replacement lamp?
View 13 RepliesJust Bought 97 Ranger 2.3L 5 speed. Everything worked except interior cab light and cab brake light. Also the wipers and A/C blower only work on highest speed when I bought it. I assumed there was a problem with the switches, bulbs and/or fuses. But when I picked it up last evening I noticed the dash lights were very dim on the way home. Then when I got home I shut everything off and removed the key. I then opened the drivers door and touched the brake pedal and the dash lights and the parking lights came on along with the "key in ignition" bell alarm each time I touch the brake pedal. If I close the door the dash and parking lights come on but the key in ignition does not sound. With so many things malfunctioning I don't know where to start.
View 7 Replies