Ford Ranger / B-Series :: Ball Hitch Won't Remove?
Feb 23, 2014
I know this sounds pathetic but i cannot get the ball hitch off of my truck. That thing is on there and i cant get it loose because the ball keeps turning when i try to break the nut loose. I have tried several ways to keep the ball still but they don't hold it enough for me to get the nut loose. I dont care about keeping the hitch i am trying to put a smaller one on and don't need it so if i have to break it to get it off i don't care.
View 4 Replies
Advertisement
OK, I haven't done a Ranger w/ torsion bars in the front , only coils. What is the best/safest way to do this?
View 1 Replies
My hitch receiver is looking pretty strange lately and I want to take it down, grind it and repaint it. While crawling underneath the truck today, I noticed that it appears the bolts holding the hitch are kind of covered by the Tank Skid Plate.
I did some searching, and from what I've gathered, it appears that To drop the skid plate means to also drop the tank as they are one unit.
Is this true? Is there any way for me to get the hitch receiver out without messing around with the gas tank?
View 13 Replies
What sort of trick do I need to perform in order to remove the cup holder that is on the front floor of my 2001 4-door Ranger. I'm hoping to be able to remove it without busting it to pieces.
View 4 Replies
Broke one of the shackle brackets. Planning on pulling the bed and doing all four. I've searched and read as much as I can in a short period of time. I have a few questions about bed removal.
1. How hard is it to remove the factory plastic bed liner?
2. Do I need to remove the spare tire to get to any of the bed bolts.
One reason I decided to remove the bed is I can't get the spare out. I figure I'll be able to fix that as well once I have the bed off.
View 14 Replies
I bought a tow hitch to put a carrier on the back of the vehicle for long trips where we might have 1 or 2 too many suitcases to fit inside.. I don't want the hitch on the vehicle for everyday driving which will be 99% of the time. It seem to me that if I could get the right size threaded studs I could just lift the hitch into place, tread on 4 bolts, and be done without having to take off the exhaust suspension bracket.
View 1 Replies
On my '88 Ranger, there is the key lock that needs to be pressed to remove the key. When I changed the ignition cylinder, I darn near went ahead and removed it. I though I better check here first, and see if I was going to disable some other function I don't know about.
View 1 Replies
2005 Ford 350. I want to change the ball joints on the front axel and I cant remove the axle out of dif. to remove the ball joint housing. I have been prying and pulling and it just moves out a 1/4 inch or so .They tell me there is no ring to remove in dif before you can pull it out but why this trouble?
View 4 Replies
My brother crashed his 2000 Ford Ranger Pick up and did some front end damage. The spindle,( steering knuckle) and upper control arm need to be replaced. I told him, WHILE YOU ARE AT IT AND THE TRUCK IS ALL APART, you should replace the ball joints and tie rod ends.AND>>>if you replace one side you should do the other side too. Front end and steering parts should ALWAYS be replaced in pairs. Also get a wheel alignment! My other brother said, don't do that if they are still ok. why pay the extra money for parts you don't need. I said, you can do it cheap, OR,you can do it right. Who is right?
View 12 Replies
My hitch is rusting so bad that I can pull it off in pieces. Surprisingly it seems to be the only major rust on my EX. I crawled under it the other day to check out how it is removed and I only saw half of 4 bolts. Those bolts look like they are under the fuel tank and I can't get my socket onto them.
My question is, do I need to drop the fuel tank to remove the hitch, and also is there anything else I should do while the fuel tank is down.(Besides replacing the hitch with a new one.)
View 14 Replies
A buddy of mine ripped the hitch off his excursion due to rust. Anything can be fixed. I will try to get a picture of it.
View 10 Replies
I just changed my Oil, added a FRAM filter and bought some good Quakerstate High Mileage and my truck runs good. However, I noticed that my Check Oil light is constantly on. I also recently changed my Oil Sender, and I wonder if that has got something to do with it.
View 3 Replies
I have a 1994 2.3l 4cylinder xlt ford ranger regular cab Manuel transmission. My transmission is going out. I found an 04 ford ranger Manuel transmission off a v6 will this be compatible? And if not what years will be?
View 2 Replies
I have a 1994 ford ranger 4x4 that I just put on and 35's and when I get to 35 mph it shakes really bad. What the problem is. Have been told that I need a steering stabilizer.
View 9 Replies
I need to change the AC relay. What is the location of the relay.
View 6 Replies
I have a weird issue. When I'm running AC on my 2.3l ranger sometimes the idle wont go down but rather hold its current RPMs till i either turn the AC off or place the truck back in gear. What that could be?
View 6 Replies
Opinions welcomed...thinking of taking a gamble on an '04 with 248k miles on it.....not sure what engine is in it.
View 14 Replies
Hello. I never did this before but could you lock one hub in 2wd and leave the other unlocked. Also can you leave one hub locked while in 4wd? I was thinking if you have one hub locked would all the power would go to that wheel? Or will this do damage?
Thanks
View 3 Replies
I fit explorer rear axle to my 2wd ranger. But now I have fromt x-member with front suspension and front drive axle from explorer. Can I fit all this stuff to my ranger?
View 2 Replies
My wife backed the truck into a pole and bent the driver's side bumper and one of the ears on the trailer hitch (the part that bolts to the frame). I bought all the parts that need to be replaced (the left bumper end, the hitch itself, and the plastic bumper cover), gut am hesitant to try to change it all myself. How hard is it to change out all these parts? Is there a write-up any where out there for this?
View 2 Replies
Fabricated own receiver hitch for the front? The ones available exit under the bumper and hang way to low, severely limiting approach angle.
I am planning on building one that exits through the large hole in the middle of the bumper, similar to the 99-07 style. I will use it for my custom generator mount and/or a small winch.
View 14 Replies
