Ford Ranger / B-Series :: Alarm Triggered / Cannot Stop It / Truck Won't Crank
Apr 10, 2016
OK- the truck is a early '96 B4000 4.0, 5 speed 4x4. The key could be pulled from the ignition switch in the "run" position (worn key/lock cyl.) I got in the habit of not using the key (never turned the switch to "lock", just "off"). No issues, been driving the truck all over with no key for some time. Now I can't find the key and alarm fob. No worries, I'll just replace the ignition lock/cyl. Done.
Now the alarm is triggered, and I can't stop it. Truck won't crank, either. I assume the no crank condition is the result of the anti-theft being active. I assumed that because I had been driving around with no key, that I did not have a "chipped" key, assuming the truck wouldn't run unless the "chipped" key was in the switch. Since it ran fine, the assumption was no chip. Now I'm not so sure.
What I would like to do is disable the anti-theft/alarm system totally. Pulling the fuse is no good b/c that kills the fuel supply. Is this possible, or do I scrap the truck? I've found 2 sources on the web that indicate that grounding the the green/purple wire that goes into the drivers door will disable the system.
View 1 Replies
Advertisement
My truck is pulsating when I am coming to a stop, a lot of you all said replace the rotors to which i did and new brakes, shocks. Today I went to get my truck all four wheel alignment done to my truck.. something is not right..
I got my driver tire facing straight, look at the left.. I went back to the alignment shop showed them that, they put it back up there, they called me over and pointed out the machine they use say, it is aligned.. So what is the problem you figure?
To update all I've done to the truck in regards to front end..
rack and pinion
upper control arm
upper lower ball joints
stabilizer inks
rotors (front)
brakes
shocks
When I straighten my left wheel, the right does not look right..
View 4 Replies
1999 XTL 4.0 auto, was doing fine, replaced Interior light bulb, now wont crank over!!! i suspect the anti theft system... how do i fix or ByPass the security system, i can start the truck by Manually engaging the starter Relay under the hood.
View 1 Replies
This has happened 3 times.
1st) pulled quickly over to side of road, shut off truck. It would not start then. Towed it to service station and it started the next morning (with no repair made). I wonder if tow ride dislodged the the blockage in fuel line(?). Always sounds like it's going to turn over, but like not getting fuel.
2nd) Went to leave work, truck wouldn't start. Towed to my mechanic and he replaced fuel pump. Thought it was fixed because it ran fine until just the other day.
3rd) Slowed down to complete stop in heavy traffic and it stalled. Would not restart. Again sounded like it was going to start but didn't seem to be getting fuel. Good samaratins pushed me off road. Had it towed to mechanic. Started the next morning without any repair or service. It's like the tow ride and bumps getting it off the tow truck dislodges what ever is blocking the fuel line.
My mechanic replaced the fuel pump, but I don't think her replaced the fuel filter.
View 6 Replies
Started up my truck today, accel pedal didn't want to move, after giving it some more force it eventually became "unstuck". Now, the real issue I'm having is from a dead stop, in 1st gear, as I'm letting out the clutch the truck boggs down as if I'm not trying to accelerate. I'm giving it as much as I normally would as I'm letting out the clutch but the motor will either die or take a couple seconds before it starts to go. Once I'm moving I don't notice any problems clutching through gears. The check engine light IS on now, however I don't have any diagnostic gear or really any tools for that matter. 1998 2.4L 5-speed...
View 2 Replies
Sometimes the check engine light comes on and truck will not start,the fuel pump runs non-stop.. when check engine light goes off,the fuel pump runs for a few seconds and stops,truck will start.... driving down the road check engine light will come on and truck runs bad....
View 2 Replies
I'm having an alarm issue that I didn't think much about until last night. Twice in the last three days I've come out to a completely dead battery because the alarm has been triggered. The first time it happen was at the gym and I thought maybe the car got bumped, I inspected it and found nothing out of place. Last night , I came out and the car was dead. This time the car wasn't around any other vehicles and was in a place that no one should have had to go by it. Something is a miss here and was wondering if any of you might have experienced anything similar? The first time it happen I was able to get into the vehicle using the key fob, last night I wasn't so lucky. I had to use a lock kit to get in so I could jump it. I had to do this because I usually separate my fob from the physical key so I don't have to carry them. Until this is resolved, I'll have to stop doing that.
One more thing, I noticed last night after getting the car jumped, I was able to drive home, park the car and when I went to set the alarm, my auto headlights would not shut off after hitting the "Lock" button several times on the fob. Every other time, hitting the lock button twice would always shut off the lights.
View 5 Replies
For my '13 GLS, I leave my fob in the center dash box compartment, and lock the doors using the button on the door. Sometimes when I unlock the door w/my key, the alarm goes off. Why is that, and how can I prevent that w/out having to carry around my fob?
View 2 Replies
I recently acquired a 2004 Ranger EDGE that seems to be in decent shape, but I am having an issue. The car alarm will just go off on it's own, usually at the worst times--middle of the night--which doesn't make the neighbors happy. Is there an easy way to disable the alarm but still be able to use the keyless entry system? If I have to disable the entry system I will do that if need be.
View 5 Replies
I have a 2008 Elantra SE. The anti theft alarm gets triggered for no reason on occasion. At first I thought it was only on rainy days, but now it happens in full sun as well.
I don't need the alarm, as nobody pays attention to them anyway. Is there a fuse I can remove to disable it?
View 1 Replies
Ok in parking lot car is armed but driver side door is unlocked press the unlock on remote will not unlock the doors however I can pop the trunk with remote. Try to start car and alarm is triggered and car will not start. I have fault codes like 00928, 01358. Is there away to disable the entire alarm so I can start it and get home.
View 1 Replies
I have a pretty stock 98 Ranger XLT (Single cab long bed) MFG 11-1998. 3.0 v6, automatic, 2wd. Manual crank windows, Manual mirrors and I presume manual locks as well (All tho aesthetically they look just like powered locks, pins sit flush with panel when locked) It has the PATs system (uses a transponder key and has the theft light). When I got the truck I got one key nothing more.
I would LIKE to have an OEM alarm system in this truck. Blinking lights, remote, that sort of thing.
My questions, would this truck have come with the alarm computer (I think its called the RAP module). If so where would it be located? If I don't have one, can I buy one, plug it in, program remotes and use it? If so how do i program the new remotes without power door locks ..
View 14 Replies
I have a 2002 F250 7.3l with an aftermarket alarm. I can't read what the third letter is on the decal MV? 2000 Modular Vehicle Security. I added a pic of the alarm decal below. The key fob it had was aftermarket for the alarm and stopped working about a year ago. Today I unlocked the drivers door with the key and the lights started flashing and I can hear a clicking sound. It done this a few times back when the key fob still worked and I just kept hitting lock and unlock until it finally stopped. It won't let me start the truck at all and I have tried unhooking the batteries with no luck.
View 4 Replies
I have a 1996 Mazda B2300 & I heard that it is similar to the Ford Ranger.
Well the thing won't crank or start.
This is what I have done so far. I wanted to put a RPM meter on it. I followed YouTube videos on how to do it. I cut the Tan wire w. the yellow stripes & try to connect the wire to thr RPM meter. Then it won't start soo idk what to do. I also took put the PCM too. (I was looking for the wire) Now be honest, I talked to a mechanic, he said thag I might have blown my PCM or Blown another fuse. But when i put the key in to crank, it won't start ot click at all. The lights come on & it wants to start but won't start.
Then my mechanic tried to start it by the... Idk what it is called but you can start it & it wont evet start. It will crank like crazy but will not start at all.
View 1 Replies
94 Ranger, 4.0, Automatic, 280k miles. Normally starts and always runs fine. Sometimes will crank and not start. Fuel pump replaced Feb. 2015 and again Dec. 2016. Have had it towed 3 times. Always starts when it gets to the mechanic. Sort of reminds me of vapor lock on the old cars with carbs, because if it sits long enough after not starting, it will start, no problem. Never died out or even coughed when running and plenty of power. When I take off the gas cap, it sucks in air like a whale. Twice I did that and it will not start right away, but if it sits for an hour or so, it starts no problem. Just bought a new gas cap 10 minutes ago and looked in a Haynes manual and a " gas tank vapor valve assembly" is mentioned. I don't want to change parts just to see what happens. Mechanics say there are no codes shown.
View 1 Replies
I have tried about everything i know about cars on this truck!! It ran great when I got it until a head gasket got blown so I tore into it and replaced them both torqued heads to specs. Made sure valves wasn't to tight. Distributor is in correct spot timing is correct had ignition module tested good!!! Coil tested good replaced both fuel pumps and put new tank and sending unit in the truck b/c it needed it new fuel filter replaced return line firing order is correct 1 4 2 5 3 6 it is getting fire it will crank and crank sometimes act like it is going to start then not also I can get it to run for about 3 sec on 3 or 2 cylinders it seems to have plenty of compression as well!! only thing really I can think of that could be wrong is computer? Also one last detail tried pull starting it as well still wouldn't go.... V6 2.9L...
View 9 Replies
It's a 01 Ranger 3.0 V6 5 spd 2wd. He drove home from work then the next morning wouldn't crank over. Turn the key and it doesn't even attempt to crank. All dash lights, headlights, etc come on. Battery is good. Took starter out and tested at parts store. Tested good. Clutch switch was good. Replaced ignition switch with no change. If I jump the solenoid on the starter it will turn the engine over. When turning the key I can hear the starter relay in the fuse block under the hood clicking. All fuses were good. I found the main engine ground wasn't hooked up to anything. I hooked it back up and still nothing. All battery connections were good but cleaned them anyway. Not really sure where to go from here.
View 6 Replies
I lost the windshield wipers, speedometer, dome light, door alarm. Check all the fuses I can find all are ok. Whats wrong.
View 7 Replies
Getting the Banana ready for it's smog test appt at the shop last night (it WAS today) Check engine light had popped on and it had been starting to sputter and surge at the idle occasionally for the last few days so I took a look at the MAF and saw dirty wires. Aha I can fix that, a couple squirts of MAF cleaner, plug it back in and voila! No more light, the Banana ran down the road around the block, over the hill and through the dale like a champ. I shut her down and call it a night.
This morning, hop in and fire the Banana up like usual and all I get is a nice peppy crank over. The Banana has had a bunch (pun intended) of new parts throw at her recently... new battery, starter solenoid, plugs and fuel pump relay and fuel filter. All within the last couple of months.
Out of complete disbelief, I ground on the ignition for a little while and she finally kicked over and sputtered to life. I let her idle a couple of minutes and things seemed fine so off we go. I make it about a block before the Banana starts hiccuping and bucking like something possessed and dies.... kaput.
The Banana has a 3.0, manual transmission and at least half a tank of fuel. Long story short and a tow truck ride home again, half a day trying unsuccessfully to pull a code, any code.... nothing. She will half-heartedly cough and spastically run with ether shots and near as I can tell I'm not getting fuel to the fuel rail relief port. I'm really hoping there is some way to diagnose a faulty fuel pump without having to drop the tank and fish the damn thing out.
I'm not hearing it run when the ignition is turned on but then again I don't think I've ever heard it run. Any other things to try before I replace the pump itself???
View 13 Replies
I have a 2005 Ranger 4x4 4.0 automatic with an intermittent no crank, no start issue, So the problem has been getting worse over time This time when it wont start, all of the lights work, the radio, the fan, etc. They are all bright and functioning.
The battery is brand new and showing 12.9v at rest. (Yes, I have tried to jump it and charge it to be sure). However, The gauges are not functioning when the key is turned. I have no click, the lights don't dim, nothing happens when I turn the key.
Another neat point, if I turn on a directional with the key on, the relay clicks so rapidly that it won't even flash the lights. I am assuming that it is a ground someplace, but I dont even know where to start on this truck.
View 14 Replies
I have 2000 Ranger 4.0L 4wd, 5sp ...
Just in the last month or so as out temps have been dropping off I've been having troubles getting her started. It happens both when the engine is cold, ie first start of the day, and after starting when warm. It did it a couple times last spring, but then all summer and fall I didn't have any problems (warm outside air temps) but, now its happening again. I'd say any time the Outside air temp is 40F or less, I am worried it won't start. IF i get her to start, everything else is just fine and she runs like a top. Here are the symptoms and what I've done so far.
When I crank I will get a couple cylinders to fire for a second or two then it falters out behaving like fuel starvation. Then I crank again right away and nothing fires... just cranking over and over. If i wait a minute and crank again same symptoms or it will fire right up. Baffling!
I thought Idle Air Control valve and sticking fuel pump relay, so I threw new parts on, but no fix.
About 75% of the time if I turn the key on, hear the fuel pump running, turn key off and on, hear the pump again x3 and then attempt the start it is successful.
Unfortunately, I don't have a code reader, or fuel pressure test equipment. The check engine light is NOT ever on. DO I HAVE A FALTERING FUEL PUMP??? I've heard thats tough to change out.
View 5 Replies
