Ford Ranger / B-Series :: A/C Works Occasionally - Blend Door?
May 28, 2015
Compressor clutch engages, lines are cold, when it works air is cold. A/C guy thinks the blend door isn't working right, is it vacuum operated or electric?
View 3 Replies
May 28, 2015
Advertisement
Ford Ranger / B-Series :: 1998 - Replace Blend Door Actuator?
I purchased a 6.7 Diesel 2014 F250 Super Duty Crew Cab about 3 months ago. Yesterday I started my truck using the remote starter from inside my house. Seconds after I heard a loud noise. Looked outside, saw nothing and thought nothing of it till I went to open my door and realized that the driver door window shattered! I live in a quiet area, it wasn't a rock thrown at my truck or anything like that, it just Blew!!!!
I'm wondering if the truck might have some sort of pressure or torque if you wish on that window to make it just pop! My mirrors were folded in however I can't see that playing a role......
Ford Ranger / B-Series :: 1997 - Blend Door Motor Removal?
My actuator/motor doesn't have the screws that hold it on. It's just clipped down. Can I just pry it up & off with out it breaking the clips that hold it down? It's a 97 Ranger.
View 2 RepliesFord Ranger / B-Series :: 1999 - Blend Door That Channels Air To Dash Vents Is Opening And Closing
Started the other day. Seems like the blend door that channels air to the dash vents is opening and closing as it feels like it. Sometimes open for awhile, sometimes closed. The defrost vents keep blowing cold and normal while doing this.
View 9 RepliesFord Ranger / B-Series :: Pinging Occasionally From The Exhaust
Since putting my new exhaust on (post-cat)... I've had this "ping" occasionally from the exhaust. Sounds as if someone is taking a small metal bar and hitting the exhaust. Random intervals, pretty loud, does it whether the engine is off or on. Only does it when warmed up though. I can't narrow it down due to the randomness of it.
View 5 RepliesFord Ranger / B-Series :: 2003 Won't Start / Turnover Only Occasionally
Okay so the other day my ranger wouldn't start after i got off work, it would turnover only occasionally but now it wont even do that. I've tried the fule turn on/off switch underneath the passenger glove box. I unscrewed the fuel like valve cap and pressed the pin but the fuel like barely squirted out so does it mean my fuel pump is bad or what??
View 9 RepliesFord Ranger / B-Series :: 1996 - Heater / AC Blower Only Works When Warm Out
I have a 1996 Ranger that the Heater/AC blower only works when the outside air temp is above 45 degrees. I have replaced the relay, and the blower motor resistor. What could be causing this?
View 3 RepliesFord Ranger / B-Series :: 1999 - M5OD Popping Out Of Third Gear Occasionally
My M5OD in my 1999 Ranger 4x4 with 3.0 occasionally pops out of 3rd gear. I think it does it only under light throttle or coasting. Also some vibration, especially in 3rd gear. Once in a while the gears grind when shifting into third. Truck has 145,000 mostly highway miles. Frequent fluid changes with Redline D4ATF.
What could be the cause, bad synchros ? How hard is it to remove the transmission and make a repair for something like this, what kind of special tools, etc. I assume a transmission jack would be real useful, what else would I need other than the normal wrenches and sockets ? Is there a good shop manual recommended for doing this repair ?
Ford Ranger / B-Series :: 1999 4x4 - Clunking / Rattling Occasionally While Driving
I am considering purchasing a 1999 4x4 ford ranger. The original owner has receipts for everything done on it recently. Rebuilt transmission, New ac, New shocks, new tires. I have never owned a ford but I always loved my friend's ranger. The only problem I had with it was an occasional clunking/rattling noise when test driving. I have read and was told this can be a common problem.
View 1 RepliesFord Ranger / B-Series :: Code P0500 / Speedo Works / ECM Gets No Speed Signal
97 ranger 2.3l 5spd ... I keep getting p0500 code. the speedometer and odometer work fine. I understand they get they're reading from the OSS on the transmission. Now I also have the vss in the axle housing which I believe is what gives the ultimate speed reading to the pcm that way there is no need to ever adjust for axle ratio.
When using the torque app with my obd reader my OBD MPH guage does nothing until I get to about 55 then it bounces around randomly between 20 and 55 and once I hit 60 mph it reads correctly. I have tried 3 different vss sensors checked wire continuity from sensor to firewall examined the teeth/sprocket that gives the vss it's reading and it all checks out...
My questions are:
- What volts or ohms are supposed to come out of the plug end so I can test if the signal to the sensor is working
- Looking for wiring schematics for this sensor to pcm...my schematic only has the oss.
Ford Ranger / B-Series :: 1999 V6 - Engine Making Sucking Sound Occasionally
My 1999 Ranger with 4.0 EFI V6 engine makes a "sucking sound" occasionally. At first I thought it was a belt slipping, but now I believe it is some kind of intake air leak. If I stop the truck while the sound is on, I can open my driver's door and get to about the front of the hood before the sound stops. I have never been able to observe the engine with the "sucking sound" on. Sometimes the engine will kill when the "sucking sound" stops, if the engine is idling and in gear. If I just keep driving normally, there does not seem to be any permanent problem. What the problem is?
View 4 RepliesFord Ranger / B-Series :: 1999 - Door Seal Sticking To Door - Hard To Open?
what i have is the driver's side door on my 1999 ranger is hard to open, the door seal sticks to the door and makes it hard to open, i am afraid of breaking the door handle off, is there any thing to clean seal with to make it not stick? the seal is not sticky to touch neither is the door but when out in the sun for a while they stick together, mechanic told me to spray with wd40 that didn't
View 2 RepliesFord A/C :: Blend Door Actuator - Clicking
What is the difference between :
Part # XF2H-19E616-FA and
Part # YL5Z-19E616-AA?
The middle numbers are the same. And they look the same? the first one is mine. Blend door actuator out of a 2000 ford windstar. Will another part # work? If the connection is the same?
Ford Excursion :: No Air On Passenger Side - Blend Door?
Went into town earlier and the a/c was not blowing out the 2 passenger side vents. Could switch to defrost and it would blow correctly. The rear is working as well. The drivers side vents blow good and if you cover those with your hands to block them off its like it forces air to blow out the passenger vents. Could this be a blend door issue?
View 2 RepliesFord A/C :: 1999 - New Blend Door Actuator Won't Working?
I have a 99 EB Expedition 5.4 with EATC climate control. I replaced the heater core that had been leaking severely. When I got the dash back on I adjusted the controls with the engine running while watching the blend door actuator under the dash. it moved but not as much as I thought it should. So I drilled an "inspection" hole behind the glove box and into the plenum cover. I watched the blend door open and close when the hot/cold buttons were adjusted, but the movement was intermittent.
I'd checked the blend door for cracks prior to installing the heater core and found none. I left things alone for a day while I drove as normal. When I had time to work on it again, the actuator quit working. I figured it was damaged from the coolant leaking into the cab so I decided to replace it. It was indeed full of coolant. I bought a Dorman actuator (part #604-216) and plugged it into the wiring harness to test it before installing it. I adjusted the controls with the ignition in the "run" position and nothing happened. I'm at a loss as to what could be the problem. I've searched for this problem, but the only threads I find are incomplete or deal with the "manual" controls. I checked all my fuses and they are all good.
My questions are:
Could I have bought the wrong actuator? Would the harness fit the "manual" actuator? The part number was identified as being for the main blend door for "automatic" controls. Is there a possibility the EATC head unit is bad? It still sends air to the panel, floor and defrost when adjusted.
How do I test the voltage at the connector? I just bought a multimeter but I'm not sure which wires in the harness deliver power to the actuator. I know there are a lot of people on this site who've gone through the heater core/blend door ordeal and have lived to tell about it. What I should do next.
Ford Aerostar :: Blend Door Actuator Location
Where is the Blend Door Actuator on the ford Aerostar?
View 14 RepliesFord Ranger / B-Series :: 2006 - Door Mirror Replacement?
Replacing their door mirror with an aftermarket door mirror and not been happy with it?
I have a non-powered door mirror. if I understand my FoMoCo Workshop Manual correctly, I should be able to replace the exterior mirror glass without the need for a completely new mirror assembly.
Ford Ranger / B-Series :: Dome Light Sometimes Comes On When The Door Is Opened
So I read the posts on dome lights staying on and the solution to spray WD40 in the latch but my problem is the opposite. The light sometimes comes on, sometimes it doesn't, when the door is opened, same if using the dash switch, sometimes light, sometimes darkness. Sometimes it just barely lights up, and I see its an LED in there. 2004 2wd Edge 2 door.....
View 4 RepliesFord F-150 (2009-2014) :: Blend Door Actuator Re-Calibration Before Using?
Time for me to replace the actuator. I just have one. I've watched many videos on it but none say anything about re-calibration before using. A few posts say this is needed. Is it? if so how is it done?
View 6 RepliesFord A/C :: Blend Door Actuator Broke (Gear Inside)
I have an Explorer with automatic A/C. The blend door actuator broke (a gear inside) so I replace it with a Dorman part (could not find the Ford ones anywhere). Part #604-202, looks identical and fits. But... doesn't work.
If I do the EATC test (OFF+FLOOR, then AUTOMATIC), the display shows error coded 024, 025, 052. What is the meaning of those?
Ford - Mountaineer :: 2003 - Very Little Heat In Cabin But Not Blend Door?
My 2003 mountaineer 4.6L has front and rear heat. The issue is the heat in the front is barely warm and the heat in the back is poor. I have replaced the blend doors front and back and I'm sure they work as I can go from cold to barely warm and back again when I change the temperature setting.
I can feel hot fluid going from the engine to the front heater core and also down under the vehicle to the rear when the vehicle is warm. The return on the front is almost cold - so heat is being given up by the heater core in front, but it seems to me that if the return is almost cold, there's not enough hot coolant delivery. The overall heat is very poor in the cabin.
The coolant temperature gauge is steady and just below 1/2 with no erratic movements. I flushed the front heater core a couple years ago. Coolant has also been flushed last year. I know that the heat is underpowered in this vehicle, but it's a far cry from when it was new.