Ford Ranger / B-Series :: 5R55E - Gasket Blowing Out Of Separator Plate
Jun 30, 2014
My buddy has a '98 B4000 4.0 4x4 Auto, and just recently he lost 4th gear for whatever reason. Which is strange, considering 5th gear still works, and OD requires direct (4th) to work.
So we're thinking its a valvebody problem, and apparently the gasket blowing out of the separator plate is a very common problem. So we decided we're going to drop the valvebody and inspect/replace the gasket.
Now I see that the they now bond the gaskets to the separator plate: What is the part number for this bonded plate?
I've also seen mentions of a TSB, and other mentions of an updated EPC solenoid. Looking for more info on this?
View 13 Replies
Advertisement
Well I finally went and bought another Ranger. Pretty red 5spd 4WD long bed. I knew it didn't run when I got it (crazy leaky fuel line...stupid squirrels), and the owner was pretty sure it had a head gasket failure. He claimed it was blowing white smoke and using coolant. I hadn't been able to get it to run to verify that, but I can't see why he would lie about that.
I finally got the fuel line fixed today (FYI, don't waste your time or money buying those Dorman OEM connector patch kits at Advanced Auto). While we were cranking the truck, I noticed gas escaping the degas bottle the radiator was pressurized before the thermostat should be open. That to me says blown head gasket (crossing fingers it isn't a cracked head) for sure. I tried to get a picture of the dipstick, but in the light it definitely looks like peanut butter. I just wanted to make sure before the massive ordeal of pulling heads/top end work that will follow
Anyway, plan is to fix her up and get her back on the road! Some picture enjoyment .......
View 14 Replies
I have a 97 ranger 2wd 4.0 with 5R55E. Drives fine in 1st and second. Slips in drive and rev.
View 6 Replies
What is the part number for the gasket that goes on the water separator on a 2003 6.0 diesel.
View 6 Replies
Dad gave me an 87 Ford ranger a couple weeks ago. I love it. Everything works except I'm having transmission leak issues when I drive her more than 30 miles or so.the symptom is fluid puking out inspection plate area. I checked coolant lines today and unfortunately they are working great. I've had a couple suggestions recommending replacement of the front seal our front pump seal (is there a difference?)
View 7 Replies
I have read all I could find on replacing a blown head gasket and and after absorbing everything that TigerDan posted on here, I dove in and began. After disassembling all the topside junk I finally got the intake manifold loose and got down to the head. I began undoing the head bolts and found two broken bolts. The head won't budge so I am calling in a cherrypicker. I don't know what kind of mess I'll find when the head comes off. I assume the head will be warped or the block may be damaged.
View 6 Replies
I have a 1983 ranger with a YFA. I recently took it apart and in the process of the rebuild I noticed the metal gasket was still in the spot where the needle pin goes. It has adhered to the carb. Any way to get it un-stuck? Also, there is a module, and the gasket comes in the rebuild kit so I know it belongs, the part number begins with 2I3 but the rest came off with the dirt. What is it for and would it hurt anything if it wasn't plugged in? It hasn't been since I bought it.
View 2 Replies
My son and I were doing a transmission flush and while we had it on the lift, I noticed the oil pan gasket was sticking out in the front quite a ways. I assume its time for a new one. Is there anything I need to know having never dropped the pan on this truck? Is this a common issue?
View 14 Replies
I have a 91 Ranger V6 4WD with 150K that has been sitting for 7 years. The last time I drove it (7 years ago) to a mechanic, who diagnosed it with a bad head gasket - leaking coolant and coolant in the oil.
What am I looking at as far as a project: besides redoing the head gasket, what else will I most likely need to do given that its been sitting 7 years?
View 6 Replies
My 89 2.9 has gotten water in the oil. One year ago I pulled this engine to replace the crank shaft (defective Ford design 1/2 thust bearing created a nasty grove in the crank allowing it to slide back and forth1/4 inch), new bearings, oil pump, timming chain, all seals and gaskets (not head gasket). The engine had great compression so I didn't do any thing more. Now I have a leak. No oil in water. NO compression leaking off into the water jacket. No "steam" coming from the exhaust. I've replace the intake manifold gasket. It showed signs of water leaking through the gasket, actually bubbles of water trapped inside, so I hoped this was it, but I still have water in the oil. I have now removed the intake and driver side head (head gasket shows now sign of leaking). No signs of water in cylinders. Is it possible to have a warped intake manifold? I have removed it twice, and I was told that some V6's need to be slowly removed VIA de-torque the bolts. I didn't do it the first two times I removed it, today I did. I plan to remove the passenger side head tomorrow. I will take the intake down and have it tested for warping. I have read many stories on this web site of the heads getting cracks, but they all seem to be in or near the valves, I assume that allows water to be burned off as a steam engine OR compression being pumped back into the water jacket.
Is there any other source of the leak that I'm missing? Is it possibly my intake? OR should I go ahead and replace the heads?
View 14 Replies
My 95 Ranger has been a good truck in the 6 years I've owned it. I had to pull the heads to replace a leaking head gasket and wound up having the heads rebuilt due to weak valve springs and worn valves. I replaced the gaskets, installed the heads, get it all back together.....won't start. Fuel pressure is good. Found that there is no spark. While putting the crankshaft position sensor connector back on I noticed it didn't look too good. I replaced the connector and that's all I did and no spark. Long story short, after a lot of research, the coil pack, cps and coolant temp sensor were replaced and still no spark.
Everything has the proper voltage to it. After a little more research I found a post with the same basic issue. His issue wound up being the ecm. So I removed the ecm....it's a used one from a salvage yard. I've owned the truck 6 years so I have no idea when the ecm was replaced. It showed up today and will get installed when I get home from work. I also ran across posts about the camshaft sunchronizer and they should be replaced at about 80K miles. Since the truck has 289K I'll replace it. Still no spark. I'm hoping it's the ecm.
View 14 Replies
I am working on my buddy's 1994 Ranger with a 2.3L I4 that has been going thru a large amount of engine coolant. The trucks has approximately 180,000 miles on it. When I had it parked on concrete I have not seen any signs of coolant on the concrete or any signs of coolant leaking. The next place I checked was inside the cab to see if there was any coolant from the heater core and there was not. The water pump has been replaced a couple of years back. I replaced the spark plugs today and did not see anything on the plugs that I would have thought were signs of coolant in the combustion chambers.
With that being said I have not worked on a vehicle with a leaking head gasket before. Would there be any visible signs on the sparks plugs? If so what would I be looking for? When standing in front of the vehicle with the engine running there is a slight smell of antifreeze being "vaporized". Are there any noted issues with this engine that would cause this? Are there any other things I should check? Could it be a leaking head gasket causing this? If so how can I check for that?
View 1 Replies
I just finished replacing the Valve body gasket in my 99 ranger with the 4.0 liter v6 with the 5r55e trans. My problem now is that I have no gears i can shift it but the gears do not engage.. I did install the updated bonded separator plate and the tsb for the blow off valve with it.
View 6 Replies
I have 2000 V6 3.0 Ranger and it has sprung a small coolant leak from timing chain cover gasket. I think just few drips after driving a while since I don't see significant drop in coolant level (Took a month to notice level dropped in reservoir) and did not see an active leak while idling. No water in the oil.
The proper repair would be to replace the gasket, but for the age and condition of the truck, I don't think it is worth it. Searching for a cheaper solution, I found K-Seal and see lots of reviews with success. Will it damage the cooling system in anyway? I think it would be worth a try even if it doesn't fix the leak as long as it does not cause any harm.
View 2 Replies
I have a real problem with 2000 Ranger, after changing the upper radiator hose and thermostat, I now have a pretty constant leak from the gasket between the thermostat body and engine. Appears to be something that is triggered by the thermostat opening, so whatever the leak, the thermostat is blocking it.
I've changed the gasket, cleaned the mounting surface as good as I could. Tried re-torquing the bolts, but on that score - what is the torque specs for the 2000 3.0 liter Ranger?
But ultimately, what the heck is wrong here? This should be a pretty brainless operation really. Am I tightening the connection too much and cracking the gasket? I guess that has just occurred to me, although the gasket is not as stiff as a typical fiber gasket is.
View 10 Replies
I have a 2000 Ranger, V6 4L, and I believe my head gasket is blown, my radiator fluid goes straight to the oil pan. It has probably been leaking for a while, I did not realize it was leaking internally, I had been adding coolant for a few months but thought it was my radiator leaking because it had a crack in the housing, so I had that changed, but then a few weeks after that It gave out. I drained, and flushed the engine twice, and just parked it. My question is, should I just have the head gasket changed, or does it need a new engine because it had been leaking for a while and not sure what kind of damage it has done internally.
View 3 Replies
Description: It will crank over forever but not start. New timing belt water pump, etc, so it is not timing. tried different fuel pump relay. no luck. new fuse no luck. The radio fuse also shorts and blows when I change it. Headlight does not come on, but the cabin "ding ding ding" sound plays. Marker, turning, reverse, and brake lights work.
CHECK ENGINE LIGHT does not come on during key turn. I may know what caused it or it may not. Before all of this happened, my audio system fuse under the hood blow. It blew again after I installed a new fuse (immediately).
One day, the wires on a portable cigarette light pump snapped and the two wires had been touch. I noticed the truck stalled several times when letting off the gas and coming to a rolling stop. The fuel pump relay makes a click noise when I turn the key
View 3 Replies
2000 Model, The fuse keeps blowing on this. I thought it was the cruise control fuse because the cruise kept not working and when I replaced fuse it would work. Only for a little though, then I looked at manual and it says the fuse is for the brake position switch. I am presuming this is just like the old days and that is the brake light switch under the dash. They use to have two wires now there is like five. Anyways I do not see any bare wires or anything that would blow a fuse, is it common for these switches to go out or what??
View 13 Replies
My dad's 1991 Ford ranger 3.0 2wd just died on him when he was driving home and I checked to see if the truck had a spark and it did not so I replaced the ignition control module, then ignition coil, then distributor and rotor cap(plug) and I put new plugs and wires on it a few months back too. I also checked to make sure that the timing chain was working as well (while I had the distributor cap off). Then I realized that the EEC maxi fuse was blown. I then found a fourm that said it might be the relay so I replaced the EEC and the fuel pump relays while I had them both out. Every time I put a new 30 amp fuse in the EEC slot and turn the key to start it the fuse blows and the truck won't start. What might be wrong?
View 1 Replies
Got a 2005 V6 Ranger with low mileage. Having a heater problem. We've replaced the thermostat, heater core, flushed the system twice, burped it to get the air out and replaced the hot water valve. The heater works for a few days then it goes cool: not cold. Adjusting "Temp" will make the temp decrease but it will not return to hot air?
View 2 Replies
Fuse #41 keeps blowing...scan tool says o2 sensor heater circuit malfunction. Problem is that when the o2 sensors are unplugged it keeps blowing fuse the second I hit the key. Where this short would be? I can't find a wiring diagram anywhere. ( I'm new to this forum and I'm sure there is a sticky somewhere..
DTC codes: P1451, P0743. P0750. P0760. P0765. P1747. P0135. P1409. P0755. P0155
View 6 Replies
