Ford Ranger / B-Series :: 4wd Does Not Engage - Lights On The Dash Flash On And Off
May 4, 2015
I have a 1999 Ranger 4x4. My 4wd does not engage when I turn the switch to 4wd lo or 4wd hi. The lights on the dash flash on and off. I disconnected the battery and now the lights are clear. But if I try again to engage it, the lights return. I feel I have a vacuum issue but would like to know more about locking hubs. If I convert them over, how do I know that my system will work? There has to be something else that changes from 4wd lo to 4wd hi. How do I check to see if this is working properly.
View 6 Replies
Advertisement
I have a 97 ford ranger V6 4.0. my 4x4 lights flash on my dash board 6 times and go out, a few minutes later it does it again. When I lock my hubs and put it in 4x4 nothing happens. What could be causing this?
View 5 Replies
My '96 ranger with a 4.0 auto will be running fine and then dies. When you go to start, the engine will will crank over. Also notice that there are no lights coming on the dash when the key is in the run position. A few hours latter the truck started right up. Not reading any codes. Transmission was rebuilt a few weeks before this problem.
View 6 Replies
Ok first I am not super-mechanically inclined but i'm pretty smart and a fast learner, lol. That said I have a 1999 Ford Ranger and two nights ago first one blinker stopped working and then an hour later the other one stopped. What I mean by "stopped" is they weren't turning on at all.
Ok so, the flasher lights are all working when turned on. I went to the auto parts store and they said I needed a new flasher. I bought it but they weren't sure which one to replace. Well there were only 3 that size in the box under the hood so I used the process of illumination. Except the new one didn't exactly fit the first one so i tried the two others. Well when I think I had it in the right one.
The Blinkers would only flash once and then that was it. The guy at the store said the flasher may be faulty but he did not have another one so he gave me my money back. I noticed on the way home that the blinkers would still flash once even with the old flasher in place. The 4 way flashers still work normally so all bulbs are working.
View 4 Replies
I drive a 1999 ford ranger and can't figure out why my 4x4 won't engage. I have vacuum all the way down to the hubs and when I turn the switch it sounds like the transfer switch is engaging but the 4x4 still doesn't engage. What do you all think could be the issue? I thought about just putting a set of the manual locking hubs on it and just be done with it.
View 1 Replies
97 automatic 4x4 SXT 4.0L. 4Hi will engage, but when I shift to neutral, press foot on brake, and shift to 4lo, nothing happens. No light, no sound. Occasionally it will make a sound, and even more rarely will light up, but it does not feel like 4Lo is engaged even when indication says it is. I pulled the shift motor and replaced, as well as verified that the transfer case could be shifted to 4 hi and lo by using an adjustable wrench. I have not put truck on stands yet, but I'm pretty sure 4 hi is truly engaging. I did attempt to engage with shift motor connected electrically but not mechanically, and it shifted. What is keeping 4 Lo from shifting? If it's a vacuum issue, wouldn't 4 hi not shift? I did check the vacuum lines and the vacuum reservoir and they seemed to be okay.
View 3 Replies
1997 Expedition ... I've looked through quite a few 4X4 issue threads and haven't seen my issue described yet ..
When in 4X4 high most times all is well but every once in a while the lights on the dash will flash from 4X4 to 4Lo then 4AWD then settle right back where it should be at 4X4. I don't think that the front axle is being affected as the truck doesn't seem to fall out of and then back into front axle lock.
My guess is that this is an electrical issue but will get to the bottom of it and report back.
View 2 Replies
I bought a 99 ranger few months ago cant the 4x4 has not worked in the truck for about 4 years. Bought it off my dad. He hasn't figured it out the t case locks in the drive shaft spins but hubs will not lock in. Has new hubs in it and still not working. Trying to get it fixed so I can park the diesel for the winter and run the ranger.
View 3 Replies
1987 ford ranger loaned it out and they said the hub spins on the driver side but the tire won't engage so it has no 4 wheel drive. Soon as I get it back hopefully today will know more.
View 14 Replies
I bought a 2000 Ranger 4x4 3.0L auto today from the neighbor guy sight unseen with a "bad tranny" for $400. I'm very unfamiliar with the Ranger family, but long story short:
When moving the shift lever, the trans doesn't engage. It needs to be engaged from underneath. Do the cables tend to stretch, or break? I can't find any adjustment on it anywhere.
View 5 Replies
I have an 02 2.0L Jetta which has started to die when slowing down or stopped. So kind of scary when you have a line of cars waiting behind you at a stop light. It only started this past Sunday and has happened 6 times since then (3 of times yesterday). All the indicator lights on the dash flash and it settles to the CEL, ABS, Bat and Seat belt light (like when you start you car, but don't turn it all the way to engage the starter). The clock and tripmeter reset. everything starts back normally when I put it back to park, turn completely off and back on.It seems like it should be an electrical problem but I'm not sure where to start, the battery and the fuses seem to have a good connection. I don't think its the alternator since the battery is staying charged too.
View 1 Replies
So I just had my entire clutch replaced while another repair was taking place. What I've noticed is the "clutch engagement" has changed. Where as I would have the clutch start to engage/disengage at the 1/2 way point on the pedal travel is now the last 1/4 of the pedal. Is this a "normal reaction to a new clutch that just takes getting used to or is there an adjustment I can fine turn it with? Do I just have to wait for it to "break in"? When I replaced the clutch on my dearly departed 94 ranger, I replaced the bearings & disc only reusing the pressure plate and did not have this issue.
View 3 Replies
I have a 2006 Jeep Commander. Periodically, and quite inconsistently, all the lights on the dash board flash on and off while simultaneously all the gauges drop to zero and the air stops blowing out from the vents. My car will continue to drive and all lights work along with the radio. This has happened while driving at 75 mph on the highway and my car will continue on as if nothing has happened. I know this isn't good, but completely baffled by it all. I have taken it to a Jeep dealer and they only saw there was a weak reading from my battery, but the battery isn't even two years old so I have yet to replace it.
I'm including a video I took while stopped at a light so you will see the RPM's drop down, but since I wasn't moving the MPH remains at zero.
View 4 Replies
I have a 02 golf and it runs great other then the reoccurring problem i have been experiencing. The problem doesn't happen every time i drive my car, but often. When i drive for a short period of time and i park and go to turn the car off, all the lights on the dash flash on and off, and most of my things restart. Some times i will stop at a stop light or sign and the car will just restart and turn off. I know this maybe something very small.
View 1 Replies
I have an 05 maxima which no longer wants to start. I've tried jumping it but that's no dice. When I put the key in the battery and brake light come on and when I try to start it there's a clicking sound from the passenger side and before the lights on the dash would flash but it has just been doing the clicking sound lately. Any guesses on what the problem may be?
View 13 Replies
I have a 2002 7.3 4x4 truck. The 4x4 will not engage, the lights on the dash don't even light up. I took it to the ford dealer and they said the fuse box and gem module. (800.00 to fix). They said the windshield leaked and shorted then out, so I needed to be replaced? I have replaced the windshield and fixed the leak, my question is the fuse box and gem a plug and play and do different years work?
View 5 Replies
My Excursion is having an issue with the 4x4 system. The. 4x4 selector switch on dash lights up properly for 4x4, but the auto hubs don't actually engage. The hubs will lock only if I manually lock the hubs. I can hear relay click, so I don't think its electrical. The hubs had new o rings installed when I did front ball joints a few thousand miles ago, and the 4x4 worked fine up until today.
View 5 Replies
2003 ranger xlt 4wd electrical - My radio lights up when driving lights are on but no clock display or anything else. My cigarette lighter and aux power outlet do not work and mym 4wd does not work. when i try to change from 2wd to 4wd no lights come on in the dash. I have checked all fuses and they are good. What to check next?
View 4 Replies
My brake lights will not work but all other lights do, bulbs and fuse have been replaced.
View 2 Replies
I have a 2006 Prius and was just on vacation for two weeks and my Prius was stored in my garage. My wife just drove the Prius about 6 miles and all the dash lights came on. The car still drives, but the cruise control won't engage. A few months back I replaced the aux 12 V battery as it somehow died, so I don't think that is the problem. When the car is off, the aux battery voltage is 12.5 volts. When it is running the voltage is 13.9 volts.
I disconnected the aux battery and then reconnected it and all the problems went away for a while. Cruise control worked again, too. I just drove it a few more miles and it happened again and just as I got home to go up my steep driveway it would only go about 3 mph. Is that the "limp mode" I have heard about? What this might be? All the dash light are lit - red triangle, check engine, VSC, Brake System, etc. I am a newbie to this site, but I did a search and didn't find much that sounded like this problem. All the lights came on previously when my aux battery died, but the car wouldn't start, so this is somewhat different.
View 1 Replies
My dash light fuse blew. I checked with a meter and I have a short to ground somewhere in the wiring for the lights. Everything else seems to be working fine.
Is there a copy of the wiring diagram somewhere?
I have the big ford shop manual but I't doesn't have any diagrams. (might be missing pages, I got it off Ebay and the index is missing T-Z).
I have the Haynes but it doesn't have the diagram for the dash lights.
View 4 Replies
