I have a 2011 Ranger. It came with Sirius radio which works with the AUX button on the head unit. This setup is not what I am use to. Anyway I want to replace the OEM unit with an aftermarket. My question is will this AUX connection effect an aftermarket radio connection?
View 11 Replies3.0 - Where is located ?
View 2 RepliesI have a '97 Ranger 4.0 4x4 5 speed, as the title says... my radio does not work. It has an original cd radio and I had installed an aux cord. After I installed it I could only get a select amount of radio stations, last week I had went out of town so I didn't drive it at all, I came back and there was what seemed to be no power to the radio at all. No display, no sound. Only the lights on the radio controls (pre-sets, volume, seek, etc.) I have checked the fuses, pulled the radio and checked everything from behind and still nothing. Could the radio its self be bad? What else should I check?
View 1 RepliesI had the intake manifold and battery replaced on my 99 Ranger and now when I got it back it worked just fine except the factory radio wouldn't turn on. Headlights​, blinkers, AC, dash lights, etc. All worked just fine but the radio will not turn on. I bought an aftermarket radio to put in it when it got out of the shop but with the factory radio not turning on I don't want to replace it until the issue is resolved.
View 2 RepliesMy 1996 Ranger Supercab XLT has the stock radio with 6-cd changer. The unit works fine but only the frequency/clock display lights up. I'm not sure where to start to fix it.
When a problem first occurred, the frequency/clock display flickered/dimmed randomly (and I think the other lights were fine). It was in the shop a few times for a fuel pump problem (the after market pump was actually not compatible and it took a bit to figure that out), and at some point after I got it back I noticed the display was fine but the remainder of lights didn't work.
I don't know if the shop did something or the failure behavior changed. What to look at? I can open the radio and fix that if needed (or replace it).
I have a 1984 ranger with the 2.8L and I am doing the valve stem oil seals.
I have instructions from the ranger station. And I have access to mitchell1 and chilton online.
Also I read somewhere about better settings to use for valve lash? The truck has about 80,000 miles on it.
Wiper problem is that they only work on high. The symptoms are as follow. The relay is working as the controls are ran thru the intermittent steps. I have tried two control switches and they acted the same. So, I believe the problem is in the motor. There doesn't appear to be any wire problems on the plug so it must be inside the motor. Could this be that grease problem inside the motor and it just needs to be cleaned and re-greased?
Radio, Has power to the plug but doesn't work at all. It doesn't appear to have a head unit fuse that I keep reading about. I have not tried to hook it up direct yet but will try that tonight. I am trying to get this truck ready to sell and need to get these items cleared up.
It is a 2001 XLT Extra Cab 4X4 with a 3.0.
I know where the filter is, i know how to bleed off the pressure. Im wondering if those clips are easy to slide off to remove the filter from the lines?
View 7 RepliesMy clutch is weak and slips sometimes and I need to replace it. ,I have replaced the clutch disc in other trucks but never a Ranger.
1999 3.0, 5 speed stick, Extended cab....
I'm in the middle of replacing my pump. With the new pump are a plastic washer and a small rubber o-ring but no instruction where they are supposed to go. They didn't know at auto zone and I haven't heard them mentioned on any youtube video. I found a crushed torn up washer similar to the plastic one in my catch pan. Maybe it is supposed to go in around the high pressure hose connection.
View 6 RepliesIs it possible to replace just the glass on the outside mirrors on a 2003 Ranger?
If so, how is it done?
I'm an experienced home mech, not really worried about doing the job. Just curious if there is any pitfalls I need to know about, or a trick/tip that may make the job easier?
View 8 RepliesI've got a '84 ranger that idles super fast for about 30 minutes after a cold start. The truck has been in the family since new and has done it since day one. I am wondering if replacing the electric choke or choke pull down would work. I've got a electric choke replacement but the cover place looks to be attached with rivets not screws. How to remove the choke?
View 3 RepliesReplacing their door mirror with an aftermarket door mirror and not been happy with it?
I have a non-powered door mirror. if I understand my FoMoCo Workshop Manual correctly, I should be able to replace the exterior mirror glass without the need for a completely new mirror assembly.
So I have ordered practically a whole front end for my Ranger. I decided to replace all the bushings, ball joints and shocks. Only thing not getting replaced are the springs, steering knuckles/hubs and sway bar. I did find that the lower half of the upper left hand sway bar bushing was completely missing along with the upper left ball joint boot. I was looking into replacing the Rack and pinion bellows/boot. I noticed that there is a line that goes up into the boot where it attaches to the body of the rack and pinion. What is that and does it need to be removed to replace the boot?
View 3 RepliesMy 1983 Ranger is in the shop. I'm being told that I need to replace the shifter assembly. I understand that this is a Mazda part, from a TK5 transmission. These parts are interchangable between bronco ii's of the same era.
View 1 Replies2003 3.0 ranger... This will be my 3rd time replacing serpentine belt and if needed 2nd. time for idler, tension pulleys...NOT SURE WHAT TO DO, should i replace parts again?
View 5 Replies1994 Ranger 4.0 XLT 4X4. My slave cylinder went out so I thought I would put in a spec clutch in while I'm in there. What do I have to pull off to get the 5 speed tranny / transfer case down? I don't want to pull off what I don't have to but I don't want to make it hard either. No Chilton on hand and I did a search on clutch but found no thread for replacement.
View 2 RepliesI've got a 2000 ranger w 158k miles, been having issues with a misfire over 65mph, and it's been throwing a check engine O2 sensor code. One of the probable reasons for the O2 code read low fuel pressure... so my husband got the bright idea of replacing the fuel pump.
That turned out to be a big story in and of itself. BUT we got it replaced with one that works, however.... now it won't start!!! You have to pump the gas and like crazy and hope that it'll start, it will eventually... but not without a bunch of coaching.
Once it's running, it's running ok. The first day after replacing the pump it was AWESOME, ran like it used to years ago, no misfire, smooth as could be, no rattle, no check engine light. But it all came back it's misfiring again, rattling when you accelerate, and the check engine is back on. I haven't had a chance to go run and get the codes ran again, maybe tomorrow I'll be able to do that in between errands. Oh, and we are gonna replace the fuel filter at some point in this week...
I have a 2001 ranger 3.0 auto 2wd and the abs light is on. this is what i have done so far. I had to replace all the front end joints so i took the front sensors and ohmed them and got continuity and voltage when i ran a metal past them and the same for the rear on the diff. so i figure they are fine. the wires to the frame look ok and i the truck has no damage so i figure the wires are fine.
I checked to see if the fuses are installed after I got the fuse layout and all the fuses are there and good. So I took it to advance auto and it came back with everything bad sensors motor controller and if anything else could be bad with the abs it said it was. I told them it is impossible for all of it to be bad. so it must be the controller. No I'm thinking the controller it the box attached to the abs pump and lines at the power distribution box under the hood.
Can I just remove that box and replace it with little difficulty or will i have parts fly out all over the place if i remove that box from the pump? All the pictures i see the the abs controller don't look the same as the one i have on my abs pump.
I have a 1996 ford ranger 2.3L automatic. I need to replace the instrument cluster. I can remove all the plugs from the rear of the cluster except 1 black wire I assume is the speedo cable. It runs from the rear of the cluster down underneath the dashboard. How to remove this cable so I can replace the entire cluster?
View 4 Replies