Ford Ranger / B-Series :: 2011 - ABS Engages At Low Speeds?
Aug 22, 2009
I have a 2001 Ranger XLT 4x4 with 38,000 miles. When I am at very low speeds (like 5 mph) and usually pulling into a parking spot, the ABS kicks on. I've heard it's the "hub" in my wheel but the dealer won't know which one to replace. Dealer said, take your hands off the wheel and see which way the truck pulls when the ABS is kicking on....well at 5 mph it doesn't pull. At $300 just for the part, I need to know which wheel it is!
Also a friend of mine had this happen to his Chevy Silverado and the replacement hub broke again so they just turned off the ABS....Is this OK to do if I don't want to fix this problem?
View 12 Replies
Advertisement
I've got a problem with my AC Compressor, with the AC on the compressor engages then disengages about every 5 seconds. Now I looked into it and some people said you can remove a washer to remove a gap. Do you think I should change the whole unit? Looked online and I can get one for $100. If I do work on the AC compressor to try and fix it or remove the whole unit do I need to drain any refrigerant etc etc. I have a hayness repair booklet and they said that to remove the ac compressor you need to get it drained by professionals. Although on the compressor I only see a electrical plug and no hoses.
View 14 Replies
2004 Ford Ranger revs the engine when you engage the clutch then when you place it in gear it's like the cruises on it want to drive without you touching the Accelerator?
View 4 Replies
My o/d has started shifting in and out at speeds over 50mph. It looks like it happens for the tiniest changes in engine loading. A windy day plays havoc and mild inclines. Sometimes the o/d light starts blinking until I switch off then operates normally. Extended warm-up driving seems to work. I've been told the rear axle speed sensor may be going bad but I have no confidence in the advice. I am driving an '02 ranger, 3L flex fuel, 2wd and just went over 100k. The atf is at the correct level but the fluid needs changing in my opinion. There are no engine codes.
View 5 Replies
My ranger started to squeak at low speeds a few months ago (when it was pretty cold) and still does it in the mornings when I first start driving it. It squeaks from around 2mph up to 25-30 and then it seems to go away (or I can't hear it anymore cause of other noises haha). It is from underneath the truck somewhere, and not related to clutch or brakes. It seems to do it in the mornings only (or when it's cold) and increases in frequency when your speed increases. Not engine related at all.
My first thought was U joints or the driveshaft rubbing, since the squeaking was directly related to how fast you were moving and clutch in/out and brakes didn't change the noise at all. I couldn't find anything rubbing on the driveshaft.
Changed the U-joints since they were kinda old, but this didn't fix the issue. Next I pulled the rear brakes and checked all the springs and such, nothing I could see was wrong. Greased up the shoe contact points and put it all back together.
It was still squeaking, so I checked the wheel bearings for play and spun them while each corner was jacked up, the bearings seemed fine and didn't make any noise when I spun each tire. I have transmission and rear differential fluid.
I've checked all of the stuff I can think of and am kind of at a loss as to the next step. I guess the things it could possibly be are transmission bearings (input/output, since those spin all the time right?), pinion bearings or rear end bearings, wheel bearings (even though i've checked them), or ??
I've driven a chevy with bad bearings in the rear end, and this doesn't sound like that. The chevy sounded like a dull roar at speed, and kinda droned a bunch. this is a very distinct squeaking sound, very similar to a squeaking bearing on the idler pulley or something like that.
View 7 Replies
A while ago I had a '99 Ranger. Long bed, regular cab, 2wd, 5-speed, 2.3. I had really poor acceleration. I was used to Toyota pickups with the 2.4 22RE, and the Ranger was considerably slower to come to highway speeds.
So, I took it to two different dealers, and they told me "that's just the way they are." I guess I believed them and sold the truck. Now, I am kind of thinking about another Ranger. Do people here think the '99 2.3 has an acceleration problem? Are there certain years to avoid the I4 in a Ranger?
View 9 Replies
I've got a 2003 Ranger 2.3L DOHC, 5 speed, 2WD. It has a check engine light with codes :
P0316-Engine Misfire Detected On Startup
P0704-Clutch Switch Input Circuit Fault
P2195-O2 Sensor Excess Lean Signal Bank 1-Sensor 1
P0171-System Too Lean (Bank 1)
The truck runs fine when coasting or accelerating but when holding a steady light throttle to maintain speed the truck starts bucking and jerking. It's doesn't feel like a misfire, more like a fuel cut out condition. When this happens and you come to a stop, you can smell that the exhaust is very rich coming out of the tailpipe. I've already replaced the upstream O2 sensor and I did a tune up about 15k ago. I'm thinking fuel pump or fuel pressure regulator. I doubt if this is related, but on start up (more so on a cold start up) the A/C compressor clutch kicks in and out 3-5 times and makes a terrible racket.
View 2 Replies
I have had my 1998 Mazda B2500 truck since 2000 and this problem comes and goes (it's mostly been gone lately). Usually when it is cold outside. At slow speeds it creaks and squeaks - kinda embarrassing - if I am sitting still it squeaks when I turn the steering wheel. Once the speed picks up you can't hear it. I have noticed this in other fords about the same year.
View 1 Replies
96 Ranger x cab 4.0 ltr automatic... Starts fine, runs fine until I stop.
When I stop, the engine idles oddly - it slows and speeds back up, tachometer and the battery gauges both lower just a bit and immediately return to normal. When the headlights are on, they dim in rhythm when the gauges dip. It does not do this in park or neutral.
Sometimes it does it right away. Sometimes it doesn't do this at all. Of course it did not do this when I took it to the shop. The battery is nearly new. Cables are fine. Alternator checked out ok.
View 4 Replies
I have a 2011 xlt extended cab with a 2.3l 4 cylinder. The truck is great... I put 120,000 miles on it in under a year.
But about a month ago the temperature gauge started malfunctioning. for what ever reason -- the truck is NOT over heating-- the gauge would increase past the "H" and then the temperature light would come on. Because the truck thinks it's overheating -- the engine goes into a "safe mode" and runs with no power. When i shut the motor off and turn it back on temperature gauge resets and the truck will run fine.
Then in another 50 or 100 miles it will do it again. Why is it doing this? I took it to the dealer here in Columbus, Ohio and the mechanic installed a new thermostat and a new "control modulator" (and a part -- not really sure what it is called) anyway, the truck is doing the same thing and the mechanic still does not know
View 3 Replies
Where the temp sensor for the rear view mirror is located. My truck is a 2011 Ranger with the 4.0 liter, AC, automatic and 4x4. I think it is somewhere by the headlights but not sure.
View 6 Replies
I have a 2011 Ranger. It came with Sirius radio which works with the AUX button on the head unit. This setup is not what I am use to. Anyway I want to replace the OEM unit with an aftermarket. My question is will this AUX connection effect an aftermarket radio connection?
View 11 Replies
I would like to install a cold air intake in my 2011 Ford Ranger. What brand should I go for? Volant or K&N?
View 4 Replies
I saw a nice very clean 2011 ranger with 63,000 miles on it . But there looks like it has a oil leak on the upper right front of the motor. Behind the pulley that does not have any groves in it . It could be a gasket or a oil seal I don't know. Is this oil leak something common with the 2.3 engine?
View 4 Replies
Installing sliding rear window in a 2011 ranger sport? Is this a DIY project or should it be left to the pros?
View 2 Replies
My 2011 Ranger with a factory Sirius satellite receiver has started showing "SAT FAULT". Checked all the usual things like: Fuse, power, connections, & antenna.
View 1 Replies
I have a 2011 ford ranger XL and I get no high beams. My low beams work fine but when I try to either activate the high beams or pull for the flash to pass they do not illuminate and the indicator on the dash doesn't come up either. I have replaced the fuse with a fresh one, even though it didn't need to be replaced, and also replaced the headlights as well cause one was burnt out.
View 1 Replies
My SC430 '02 has developed a problem with the VSC. Unfortunately it s not the light but the VSC engages at slow speeds. If I accelerate from low speeds, engine does not rev up and the VSC lights comes on. It works as if I was skidding and tries to correct the direction of the car. Just as it should if I was on ice or experienced aquaplaning, but I am on a dry road. I did a reset of the ECU, had the car at Lexus (they were able to duplicate my issue) for a zero-calibration. They found no problem with the sensors. All did not work. Presently I drive with the VSC disengaged. I do suspect the speed sensors to act up as I had Tein-Coilovers installed, but how can I get to the source of the problem?
View 12 Replies
When braking at very slow speeds(less than 5 mph), my ABS system engages. It can be startling and the truck keeps rolling forward unless I pump the brakes to get it to stop. The truck is drivable, I just have to be careful when pulling into our garage or slowing behind someone at a traffic stop. What could be causing this?
View 2 Replies
In a matter of weeks, my truck destroyed two sets of flywheels and starters. When the ignition key engages, the engine "jumps back?. Apparently, this causes the starter and flywheel teeth to grind. My mechanic cannot determine the cause of the "jump back". He thought that it might be the timing. His examination and testing, however, proved the engine properly timed.
View 6 Replies
I just bought this Ranger a really bad steering issue. When at low speeds, when I go to turn the steering "jumps/kicks." Then after I straighten out at the end of the turn it jumps in the direction that the steering wheel is being turned. This goes away at higher speeds (40+mph).
I was told by the seller that it needs a new steering pump, but my mechanic said that it was operating well. He noticed that the bearings were loose on the driver side and tightened them up. The problem went away. I just finished driving it for about 20 miles and the problem is back.
What do you think? Is there a way to easily shut off the p-steering to see if that is the problem? Is this a good idea?
View 4 Replies
