Ford Ranger / B-Series :: 2009 XL Won't Start / No Power To Headlights
Jun 28, 2016
Just got home from work with my 2009 ford ranger XL 2.3 and it was running fine, went back out 10 minutes later and it would not start. No clicking noise from the solenoid or anything. Tested the battery (12.8volts). checked all the cables, checked all my fuses and everything is good.
Then noticed I have no power to my headlights, brake lights, or instrument panel. The only power I get is to the horn and the interior light. When I try to turn my headlights on or turn the key to different positions the "smart junction box" at the passenger side kick panel starts clicking. (there are no relays on this thing)
I decided to check the battery when the key is in the start position and the voltage dropped to 5 volts. Power is going somewhere but I am completely lost here.
View 2 Replies
Advertisement
So, a couple of months ago, my Ranger lost a lot of power going down the road, and when I came to a stop it died, and wouldn't start. So I got it started by roll starting it, made it to a friend's, and then back home. I've put new spark plugs and wires in, and it needed it, badly, but it didn't work. I got a couple of codes off of it,
P0302- Cylinder 2 misfire detected(which I fixed with the spark plugs)
P1443 - which I can't find a definitive answer for
P0500- vehicle speed sensor malfunction
P0171- system to lean (bank 1)
So, the truck will turn over, and if I give it a lot of gas it'll start at stay started for a few minutes, but then cut off. When it is running it's running very very very roughly.
View 1 Replies
I have a 1988 ford ranger and my headlights won't turn on all my fuses are fine but no headlights! All the other lights work fine blinkers, parking, brake ,and tail lights! What do I need to look for????
View 14 Replies
I have a 2000 ranger and the right low beam went out, we changed the bulb to no avil. I thought it might be the light switch so we changed it also ,nothing!! We have checked the only ground, I can find for the lights (on the driver side under the fuse box under the hood). This problem has me stumped . Another problem that may or may not be related is the cargo light does not work either...
View 8 Replies
The headlights on my ford ranger 1994 won't come off. All fuses are good and wondering the next step?
View 9 Replies
1994 Ranger .. Last wednesday I had to get a jump because the lights where left on. Everything was normal on thursday. Friday morning. I went to go start the truck and notice that it would try once to start and then try a second time and it would start. Today I was driving it. The check engine light came on and when I get the RPMs up to shift up, I would loose all power and have to wait till it gets down below 10mph before I would get the power back.
View 8 Replies
The headlights on my 94' 4x4 have been kind of cloudy looking since I bought it two years ago. It's not condensation on the inside, the glass just looks like it has something on it. Is this a common problem?
View 10 Replies
ok so let me start by saying, my name is Tim, I own a 1999 Ford Ranger 6 cyl, 3.0L truck, I bought it brand new in 1999 and drove it for a few years and then took it off the road for 3-4 years then last year I went to put it back on the road and I couldn't get it running.
I took it to the dealer and they replaced a key switch module. since then the ranger seems to lack power. It also idles erratically when you first start it in the morning too.
not sure whats going on here but the engine light is on,
I get codes P0171 & P0174 (too lean bank 1 and too lean bank 2)
I would also like to note that I have replaced the fuel pump, fuel filter, transmission filter, MAF sensor, IAT sensor, PCV valve, EGR valve, TPS sensor, idle control solenoid, fuel pressure regulator & new plugs. I have also checked for vacuum leaks with no avail.
View 6 Replies
All my guages move (needle moves to the right) once I turn on my head lights. Indicating higher egine temp and higer oil pressure. What cause be causing this?
View 4 Replies
Problem with 1157 LED bulbs . I install all 4 light bulbs the tail lights and front turn signal lights the problem is all lights work with the signal lights. but when I turn the head lights the front signal lights don't work. Also the turn signal lights on my dash board both light come on
One more thing if I install the regular 1157 on the front . the LED lights on the back work fine and the from work fine . looks like the front don't like the LED bulbs. I have 87 ranger cab and half or extended cab. v6 2.9
View 6 Replies
I have a 1995 ranger four letre 5sp, dubbed Beula. I figured there'd be a few gremlins and there was and is, which I know to be more common than not in older trucks. The top priority is figuring out why when I push the lever for the high beams forward, the headlights cut out completely, whether in gear or not, and I don't know where to begin troubleshooting. I've surfed around the forums looking for answers and really only found conjecture.
View 14 Replies
he has a 2009 ford Ranger, 2.3L .with 54thou miles, the Issue is Vibration during in gear and stopped at a light no vibration at higher rpms during driveing, he states vibration happens in park ,neutral,reverse and drive. had the truck in for repair in two separete dealers they couldent find the problem its an automatic trans. he states from day 1 this truck has had the prob now its out of warrentee.dealer told him that trans to engine alignment was the prob dealer did some alignment and worked for a few weeks.
View 10 Replies
2000 ranger auto 3.0 wife said that she had problems starting the truck
She had wiggle the shifter to get it to start. Have not looked at it yet but i am think the newtrl safety Switch.
View 3 Replies
I have 1994 ranger 2.3 2wd will not start when key is turned to start position - when clutch is depressed there is a click from fender mounted solenoid but it never cranks motor or starter--I need wiring diagram to trace origin of wire on starter solenoid because it does not have 12volts on it--when I jumper 12v on it and have it in neutral it starts up and runs but no voltage and no start with key....
View 2 Replies
I have a 2000 Ranger 4.0L manual transmission. I just replaced the starter/solenoid on it a few days ago. I went to start it, and I got 1 click and the whole system goes dead (ie: lights, instrument panel, everything!) I checked all the fuses and the starter relay in the fuse box. All good. I tested the battery, it's charged and good. I even tried jumping it. Same problem.
I can remove power from the system, re-apply power and same issue. I'm not even sure where to start here. I checked the ground terminal on the battery. It's connected to the frame and clean. Cables are tight to the battery and clean.
What am I missing?
View 2 Replies
I have heard from a few people that it might be the computer that is messed up. Just replaced cap and rotor, spark plugs, wires, fuel filters. Pump turns on. Cranks and cranks but won't start. Took the intake cover off and tried starting it, all it did was back fire. Checked the firing order and everything is right. So im left with guessing at the computer and ignition??
View 5 Replies
I have a 02 ranger..3.0 standard trans 4x4.... Started running crappy, cleared up and when shut off, now wont start... Good spark and good gas pressure... Seems to want to try, but just doesn't go. No codes or pending codes.
View 8 Replies
I've got an 83 ranger that has proven to be a bit of a head-ache. For starters it's got a persistent oil leak. It's somewhere in the area of the distributor, intake manifold, block region on the backside of the engine, but I can't get back there to see it.
Secondly, the truck only seems to want to start when I give it gas. Even when I use starter fluid, it will only get to an idle if I hold it to the floor when I turn the key. What this might be?
View 14 Replies
My 1991 ranger with a 4.0 turns over but will not start. It acted like it ran out of gas put again seems to do ok then it did same thing it sat over night then would not start so I thought I would put some gas in the intake so it starts ran real rough but smoothed after a few minutes ran fine after that next morning same thing no start did same put gas in intake at first no start just turned over didn't even try let it sit for awhile then tried again it fires up ran rough but ran now I get nothing just turns over pulled codes 22and 122 replaced both had ignition mod checked its good new coil pack no change so at this point i hear fuel pump kick on fuel getting to fuel bar but seems a bit week on pressure going to get pressure gauge and see what it says but in the meantime I am loosing my mind...
View 9 Replies
My 03 ranger with a 2.3 I4 does not want to restart when it is above about 80 deg outside and engine is warm. Will crank, but as soon as fuel in line runs out it stalls, like a vapor lock. After about 45 mins can push start normally( has manual trans) but have to wait about 2 hours to use starter to start.
View 11 Replies
2002 Ranger XLT auto 3.0 will not start after it has run awhile, Was very intermittent at first sometimes six months would pass, sits for and hour or so and would start right up and run great. Lately it is becoming more frequent. Good fuel press, good spark, I have changed the coil pack, fuel relay, filter , am at a loss.
View 6 Replies
