Ford Ranger / B-Series :: 2008 - Runs Rough With No Power
Jul 23, 2012
I just changed the plugs and wires on my 2008 Ranger 3L. Now it runs rough with no power. It was fine before I did the work but I thought I should change the plugs at 215000KM. I used Ford wires but unfortunately I used Bosh platinum plugs and now think I will change to Ford plugs. Do you think the Bosch plugs would be that bad for the Ranger? What is the belt tensioner torx size? I had to move the A/C compressor over to get the #4 plug but had a very hard time trying to loosen the belt.
View 7 Replies
Advertisement
My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr
View 5 Replies
This has been an ongoing issue for about a month. When I start the engine after it has been sitting and is cold it runs ruff for about a minute then smooths out and runs fine. I pulled a P0304 code (cyl.4 missfire) but I do not get a CEL.
I checked the plugs and they were ok but I changed them and the wires anyway as it just turned 50k and the plugs were original. I could live with a little cold ruff idle but the code throwing bothers me. The truck is a 2000 xlt 4x with auto trans. and 4.0 engine. This is my second 4.0 ranger but I have only had it for about 6 months.
View 9 Replies
I am working with a friend on his 99 Ranger with a 4.0 . When first started it will idle rough and hesitate for the first 300 feet or so, and then clear up and run smooth the rest of the day. If he lets it set for 6 or more hours it will repeat the problem. He has taken it to a local Ford dealer and they have replaced spark plugs, plug wires, coil pack, cleaned the throttle body, checked the air idle motor and passage.
He has had it to the dealer 3 times and their latest plan is to pull the heads @ a cost of 1500.00 to start. Since it runs well, no coolant in oil or oil in coolant nor loss of either fluid, I couldn't figure why they want to pull the heads.
To date it has not thrown a code, I ran it on a New Generation Star tester and cannot find a code. The truck runs great after the first intial start up and does not give any signs of cutting out or lack of power. My guess is it is losing fuel pressure overnight and is taking a while to reprime. Original fuel pump and 160K miles. Will do a fuel pressure test this weekend.
View 1 Replies
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 Replies
1990 Bronco II, 2.9l, auto, 4x4. Was running just fine. Sitting in Park just idling away. All of a sudden, just starts running real rough, ticking, etc.
Towed it home. This morning, started up OK but still running really rough.
While running, pulled spark plug wires one at a time from the drivers side. Had no effect but could tell the wires were sparking as I held them up to metal.
Turned truck off. Drivers side exhaust manifold COLD, passenger side HOT.
This sounds real bad to me. Am I missing something simple that could cause the drivers side of the engine to not work?
View 4 Replies
168K, to date, replaced
rear 2 cat's
Timing chain and gears
cam sync assem.
Plugs, wires, dis block,
Why.............. Read on
This 2003 ranger 3.0 v6, run very hard at idle, yet it runs and you can drive it around town, ""at"" low rpm, and no hills but it gets from point a to point b
I have no pre ingintion, but a plug that was only 60 days only was burnt out completely on 3rd cyl. bank 1 or as ford call it #3, i am telling you this thing seem like it running on 4 cyl,s kicking back and forth, and replacing everything above made no difference.
On the highway, as long as it is flat or down hill 75-80 mph, as soon as a hill or power to pass is needed it bogs down and slows it self to about 45 mph, I have been though everything i can think of and my next move to to start pulling heads, but i wanted to ask here first.
View 14 Replies
My brother's 87 ford ranger 2.3L truck began to have problems. It would be running great, then start to misfire, run rough, sputter, shake and loose accelleration then die. Then it wouldn't start back up for a long time, sometimes til the next day. Little by little, the truck would drive a shorter and shorter distance between breakdowns. He first tried some minor work himself, (basic tune up) - replaced his rotor, cap, plugs, air filter, fuel filter, but that didn't fix it. He went to one garage (big mistake), who said the fuel pump pressure was fine but said he found a broken wire on the harness grounding out and it needed new ignition module and replaced it. (Cost was $350.00+), Garage promised to honor any additional work nec if it continued to have the same problem, and would be free of charge.
Five more breakdowns later and two more "better quality ignition modules", new battery terminals, and 1 new computer later, this joker did more unauthorized work and demanded another $200+ besides the fact of breaking his orig agreement "free of charge" if any further problems! Needless to say, second garage fixed the truck by replacing the magnetic pickup, part # DU 30-C (an electrical part that goes in the distributor and pulsates a current to operate the timing) (it does something like that) and the truck has been driven approximately 40-60 miles as of today, (3 days later), without breaking down. All the other times when picked up from incompetent garage, it wouldn't go more than 1 - 7 miles before breaking down and each time they didn't fix it.
View 4 Replies
I have a 94 Ford Ranger 4x4 4.0 V6. It has developed a rough idle and has lost i fair amount of power. I cleaned the maf sensor and iac valve. Along with replacing an o2 sensor that was reading bad, with no improvement. The guys at O'reilly took a look and think I may be dealing with a timing issue or a warped valve. My question here is to found the culprit? I'm very inexperienced at working on vehicles and am damn intimidated by the scale of a project like timing. I should add that while traveling on the highway in high gear at low rpms, it develops a rough stutter. I can either power through it or ease off to get it to stop, but it resumes shortly after. It almost acts like an egr valve stuck open when on the highway. But that doesn't account for the rough (a consistent put, put, put...) idle.
View 4 Replies
My 2001 V6 Ford Ranger Edge has 124, 000 miles and always ran very well, Shortly after a minimal attempt to pull a vehicle out of a ditch the vehicle began to run poorly. This may be coincidental as problem did not begin straight away. The engine refused to start at first but now appears to run on 2 or 3 cylinders. I have checked AND CONFIRMED the following:
Spark at all cylinders
Fuel filter replaced
Fuel pump checked
Fuel pressure 56 psi at schrader valve on fuel rail
Fuel inertia cut off valve checked
E_Z start sprayed in feed horn did nothing
I hope to avoid towing it to the dealer,as I recently had a very negative experience doing this with the Honda dealer..
View 3 Replies
My girlfriend has a 97 Ford ranger that can't make it out of the driveway when it warms up to operating temp. This is what was replaced thus far. Cat, timing belt, plugs and wires, air and fuel filters. It has about 37 psi at the rail, the codes shown were second 02 sensor, and fuel to lean on bank one? I looked thru a few postings but I'm actually at work and can't really spend too much time looking thru much more. The timing was checked about three different times just thinking that was the problem after the new belt was installed. It does idle perfect at all temperatures it just won't go when it warms up. Unplugged the TPS, no change, was thinking electronic ignition module but not sure if it has one or where it is if it does.
View 11 Replies
My 1995 ranger was running just fine then today overheats in five minutes and then runs at very high rpms, has 2yr old water pump new tstat don't think head is blown no water in oil no white smoke no water on the oil cap, I haven't check the plugs for water, stated raining no garage, when engine is cold starts runs fine,but when it gets hot its like a train...
View 5 Replies
'88 Ranger 2.9L V6 starts and runs but shuddering. Most noticeable when shifting and revving the engine. Will a dead cylinder cause this? How do I check?
View 2 Replies
I have a '92 Ranger with a 2.3 liter engine. She starts and runs a couple of seconds and shuts down. I'm thinking maybe a fuel pump is not putting out thepressure needed. Gotta go to work tomorrow and gotta get the truck running today.
View 2 Replies
I have a really nice 1986 Ranger XLT with a 2.9 V6 (injected) and OD Automatic with about 135k miles. I've had the truck for over ten years and have been pretty happy with it. I'm still trying to correct a couple of nuisance items:
1. Sometimes it runs smoothly, and at others it has a rough idle, and once in a while it will even stall. Before it stalls, it idles or runs roughly, and will miss erratically. When it quits, it does not fade out like it is running low on gas; it quits suddenly, like the ignition is turned off. If I am driving at highway speeds, sometimes it will buck as it misses, and sometimes stalls out. But it always starts up right away afterwards. This does not happen often, but when it does, it happens several times over hours or days, and then goes away by itself for months, even years, and then comes back for another round.
I was hoping whatever was wrong would totally fail, but it has been several years and is not getting better, nor worse. Fuel mileage varies, too, from 16 to high 20's MPG. I have new low- and high-pressure fuel pumps (dual tanks), new gas and air filters, checked all the electrical connections, put in a new ignition switch, new O2 sensor, Air Flow sensor, EGR, replaced all the vacuum lines, new battery and cables, new starter, all new electrical relays, fuel pressure regulators, new fuel pump inertia switch, tuned up engine (incl. wires, cap, rotor, ign module, plugs and timing), and cleaned out the already sparkling-clean tanks.
2. My oil pressure will drop at idle to low-normal when the engine is warm. It never goes to below Normal on the gauge. I have replaced the gauge, sending unit, and oil pump. This is a long-term issue, and is not getting any better or worse.
View 2 Replies
Before and after this speed it runs fine, so what could it be. The check engine light is now on all the time.
View 2 Replies
Sometimes the check engine light comes on and truck will not start,the fuel pump runs non-stop.. when check engine light goes off,the fuel pump runs for a few seconds and stops,truck will start.... driving down the road check engine light will come on and truck runs bad....
View 2 Replies
2008 f150 5.4 30,000 miles the engine has top end noise on the right side and runs very rough no codes cam problem ?
View 4 Replies
I recently replaced the plugs cuz I had a rough idle all the time. During plug change when I discovered they had already been changed I found one that had a burned off electrode. Does this mean a lean condition exists?
After plug change it runs smoothly but only after 10 min warmup in our canadian winters. I can drive it when its not warm but seems to have less than full power and idles very badly after driving w/o proper warmup.
Next I changed fuel filter and checked fpdm, it was a little rusty but not bad so i just mounted it 1/4 off steel to prevent further rusting.
Since then I have installed a programmer [diablosport] but found no codes since i had battery disconnected for filter change. no new codes in last few weeks since.
So do I have a lean running cylinder causing this poor cold idle or a rich cylinder? It must be a clogged or dripping fuel injector right?
View 2 Replies
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 Replies
I have a 2001 Ranger edge edition with extended cab, 3.0L engine, auto tranny (I believe it is a 5R55E) with 95000 miles. I am currently having some rough shift problems going from 2 to 3 and 3 to 4. I had the transmission fluid exchanged and it solved the issue a little bit but it hasn't gone away. It seems to rev up a little then shift real rough. I have read hundreds of threads that talk about the Valve body gasket blowing out on these trucks so I was wondering if this description matches that fix (The OD light does not flash when this happens).
I had to have the PCM replaced right after I bought it to get the emissions to pass (codes wouldn't set) and in the process cleaned all my ABS sensors, replaced my Speed sensor on the rear differential and replaced both rotors.Are there some home diagnostics I can do to narrow down my search for the problem? Also, on a different note, my father has an 03 with the 4.0L SOHC in it and it seems to get a heck of a lot more get up and go. I understand it is a larger better engine but what I am experiencing seems very sluggish for any V6. Could they be related? Might it just be a fuel filter?
View 4 Replies
