Ford Ranger / B-Series :: 2007 - Shifts Into Gear But No Drive
Jun 19, 2013
My gf's dad said I could have his 07 Ranger 4.0 2wd with 230K on the clock if I fix the tranny 5R55E. One day he was driving home and all of a sudden had no drive. The tranny will run thru drive, neutral and reverse, but has no drive to it. Engine revs with nothing to show.
Tranny fluid was very dark and pan had nothing but the usual "metal flour" in it. I stopped there, did not pull the filter or anything else.
View 3 Replies
Advertisement
I have a 98 XLT 4.0, auto trans with 109K miles and when it's really hot outside and it's been driven when I start back up and put it into drive it sometimes takes a while to go into gear. A friend says the transmission fluid doesn't look too good and it smells. Obviously I have a transmission problem but my question is would changing the fluid do any good at all? Since the tranny is bad what harm could it do? The fluid was never changed previously.
View 6 Replies
2007 Ranger 4.0l, idles rough at low rpm, in park or drive, with or without the AC on.
View 1 Replies
The trucks seems to Idle Rough in Park and Drive, Cold or Hot. It mellows out as soon as I give it gas but at stop lights or in park it goes back to a seemingly rough idle.
This is my first Ford Ranger and dont know if its normal. No code or dummy lights.
2007 2WD 4cyl
View 2 Replies
I have a 2007 Ford Ranger 3.0TDCI when I drive on a road that is bumpy or on a ground road the ABS light keeps coming on , sometimes it just flickers other times it keeps on for about 5minutes. I when for a service 3000km back but they told me the brakes is fine. What it can be?
View 1 Replies
There is a clunking sound and feel from the front end of my 2007 Ranger FX4 when in 4 wheel drive. This happens sometimes but not always on engaging or disengaging 4 wheel drive, as well as sporadically while driving along. I took it back to Ford on warranty with this problem last year, and after a few attempts I had them admit that something was wrong and they finally diagnosed that it was the front drive shaft that was binding where it leaves the transfer case, this was replaced. I have now put maybe 50km (max) on in 4 wheel drive and the problem is back, I don't think the problem was ever fixed.
View 14 Replies
I have an 03' Ranger and I assume it has the BW 1354 tcase. I am getting a "clank" sound when the truck shifts from 1st to 2nd. I am thinking its the rear output yoke on the t case. I can grab it and move it up and down but there is no fluid leaking or anything. Would this be a rear bearing problem?
View 2 Replies
I got this 89 ranger xlt with a 2.9 and automatic transmission. I mainly bought it because it was in such good shape and I was planning on putting a 5.0 in it. everything works on it. the a/c, radio, lights and it runs real nice. the only problem it has is it shifts pretty hard going into second gear. every once in a while it will shift smoothly into second but only like once or twice a day. he said he had recently changed the trans filter and fluid and the fluid does not smell burnt.
View 7 Replies
Just recently my 2003 3.0 Ranger has started to rev high between shifts. With the clutch in the it will continue to rev high for 8 to 10 seconds. Where should I begin to look to correct this problem?
View 4 Replies
My '03 Ranger is having a high idle problem. It's a 3.0, manual, 2wd, 141,000 miles. When it's cold it will idle at about 1500 but once I drive it, even just to the end of the block, it will idle at about 3000 and shoot up towards that between shifts. At a traffic light it will idle at 3000 and maybe go down to about 2500. If I bog it down with the clutch it goes right back up once I put the clutch back in or put it in neutral.
I replaced the IAC, no luck. I cleaned the MAF and checked the voltage on the TPS and it is good. I replaced the PVC valve, but the old one was fine anyway. I've sprayed around with carb cleaner and don't notice any difference. I've plugged it into my dad's AutoTap which lets me monitor everything on my laptop and the only thing I can see that looks suspicious is that even with the engine off, the Absolute Throttle Angle reads 18.8%. If I step on the gas with the engine off it goes up to 91.8% so I would imagine that just has to do with the function of the TPS and probably isn't out of the ordinary, but I don't really know what that number means or what the Absolute Throttle Angle is or is supposed to be.
Short of taking the intake plenum off and physically inspecting it for cracks, I'm stumped.
View 7 Replies
I bought a 96 Ford Ranger XLT Supercab 4.0 on the 21st and the gear shifter doesn't go into 1st gear but changes to the other ones(see pic below) and was wondering if it's a easy fix.
Also I have a oil drip(at least it looks like oil to me) and I can't figure out where it's coming from because it's a small drip and the oil dipstick and tranny dipstick both show full and I can't figure out where the drip is coming from and I only noticed a dip on a metallic tank but don't know what that is either but check out the pic below to see the drip I circled.
View 3 Replies
I purchased a 1990 Ranger 4x4 with a v6 from auction. Took it to local shop to have them check it for me. Found out that it has a 3.0 in it and mechanic believes it is from a taurus. Truck actually runs extremely well. Has a few codes due to the ECM is for an automatic trans. Now the problem. I was on the highway-in 5th gear. Terrible noise the nothing. When I got it pulled over. The drive shaft was hanging from the rear end. It had been twisted like a straw. The transmission side had the yoke only, and the tail housing was cracked. It rolls and the drive shaft at the rear end turns. I figured the trans locked up. I don't know what trans to look for---is a 90 2.9 5 speed the same on a 3.0 ??
View 6 Replies
I have a 97 ranger 2wd 4.0 with 5R55E. Drives fine in 1st and second. Slips in drive and rev.
View 6 Replies
I recently replaced the oil seal on the front differential where the front drive shaft connects to the diff. I believe it is called the pinion oil seal. I had to remove the drive shaft to do the job. Got the oil seal in place and then slipped the u-joint yoke on and hand threaded the retainer nut on to get it started. I did mark the relative position of the drive shaft to the front yoke and the rear yoke. I had previously noted that the retaining nut, before I took it off had about 2.5 threads showing. I had to remove it with an impact wrench.
So...I used the impact wrench to put it back on with about the same number of threads showing. I then reinstalled the little short fronmt drive shaft...the one that comes out of the transfer case. I got the front of it on to the pinion output on the front diff...and then had to reattach it to the transfer case end which, by the way an interesting affair with a sort of metal cone that is attached by 6 8mm fine threaded bolts about 2.5 or 3 inches long. Got all that done with much grunting an groaning - I'm laying on the ground - SO the oil, leak is fixed but now ...
There is a vibration at around 40 mph and higher. like something is out of balance. did i damage the front diff pinion bearing by using an impact wrench? this vibration occurs in 2 wheel drive. as i understand it the front drive shaft doesn't even turn when in 2 wheel drive. my question is does the front diff gears spin when in 2 wheel drive? perhaps the u-joint is bad on the front drive shaft? just a bit baffled. when the speed drops to below 40mph the vibration goes away...
View 2 Replies
I bought a 99 ranger few months ago cant the 4x4 has not worked in the truck for about 4 years. Bought it off my dad. He hasn't figured it out the t case locks in the drive shaft spins but hubs will not lock in. Has new hubs in it and still not working. Trying to get it fixed so I can park the diesel for the winter and run the ranger.
View 3 Replies
I have a 2000 4wd Ranger with rear anti-lock brakes. The ABS light comes on every time I start and drive less than 100yds. It stays on until you shut the truck off. I found the test plug, and followed procedures to get the codes, but the ABS light won't flash at all. I checked fluid level and fuses. I replaced the rear sensor about a year ago, when that went I lost speedometer and OD off light stayed on. I wouldn't rule the sensor out, but I'd like to get codes. To get codes I grounded the Black/Orange wire with the key in Run position.
View 10 Replies
Daughter driving truck truck quits moving, I get there no drive and no reverse, has low and 2nd manually.
drive truck home, flush trans and cooler, road test all ok. this was 3 weeks ago.
This morning did it to here again, no drive and no reverse, she drove it home using manual low and 2nd.
I get in and when put into drive it feels like it tries but doesn't go all in, same with reverse. pulled it into low and vola I now have drive and reverse again
I'm thinking a we may have a bad or going bad shift solenoid. What I need to know is, is any of the solenoid valves on when in reverse are they the same as when in drive?
View 3 Replies
My '02 4x2 has developed this half scrape half squeak noise in drive. 140k, 55RE trans, all original drivetrain. It sounds like someone wrapped a wire coat hanger to the driveshaft. (No, I looked). It seems to be in sync with the speed of the shaft or wheels. U-joint maybe? If I have to take it to a garage I'd like to have some clue what to tell them to look for.
View 4 Replies
My 2004 Ford Ranger has 220,000 miles, runs great, and when I bought it this summer the 4 wheel drive worked great. Starting when the weather got cold when I engage the 4 wheel drive (no lockouts electronic engagement). I will drive and it will kick in and out of 4 wheel drive when it starts to slip or I have to accelerate.
When the 4 wheel drive kicks out I will let off the gas then it will engage again on its own, but will slip out again when on ice or I start to slip. When the 4 wheel drive engages it does NOT make any strange sounds, no clunking or nothing, it engages smoothly, and disengages properly.
What it could be? a connection? Any way to fix or diagnose the problem? I have been told that it probably is not the transfer case, because if it were it would not engage or stay in 4 wheel drive at all.
View 11 Replies
Last night I backed up out of a parking space and when I put it in drive it wouldn't move. It seemed like the transmission was locked up. What happened? The truck was running fine. It's a 2002 Ford Ranger 3.0 with auto transmission. Getting it serviced? I'm tempted to go to a dealer. What the problem is? Repair costs? The fluid looks good - no burning smell.
View 5 Replies
I have a 97 Ranger 4x4, 4.0L, A4LD, 68k mi. with P0171 and P0174 codes, lean fuel mixture banks 1 and 2. The truck will rev up and down from 500-1000 RPM when Im rolling in Drive. When I accelerate, its fine, but when I let off the gas and roll it starts revving again causing the truck to shake. I replaced plugs and wires before the codes (1-2 months ago). After the codes came I replaced the fuel filler neck (not because of the codes), cleaned the air filter, cleaned MAF, changed fuel filter, and checked fuel pressure which was at 29psi so I replaced the fuel pump. Is there any common causes for this? Cures?
View 14 Replies
