Ford Ranger / B-Series :: 2007 E250 - No Access With Key Fob While Engine Is Running
Apr 14, 2012
I have a 07 E250 which has a great option where I can lock the doors while the engine is running and then access the vehicle with my key fob. That is great during the winter when you have all that air mass behind you to keep warm.... plus NOT living in the city, I dont have theft issues like they do.
Anyways... I purchased a 99 ranger 4x4, also with keyless entry. I managed to make 1 fob work both vehicles. I discovered however - that my 99 Ranger WILL NOT allow access via the key fob while the vehicle is running?
BTW - the 07 E250 does not have the ignition key with the chip, where the 99 Ranger does.
Breaking into a 99 ranger is alot tougher than it looks !! But I gotta admit - had alot of fun watching all the local good-o-boys trying to assist me in regaining access to my vehicle.
How do I bypass the "No-access-while-running" feature?? If feature cannot be bypassed - is there a way to temporarily turn off the Theft Feature while while the vehical is running - as in a bypass toggle switch??
View 3 Replies
Advertisement
1986 Ford Ranger / 2.3 EFI / 140 CID OHC /4-Cyl/5 speed
So the last time I was here, I was having doggy issues which I thought were fuel related. I'm still having issues, although it appeared to cleared up a bit.
When I start the engine, it cranks over, I'd give it some gas, it would rev up, then suddenly die, no matter if I pressed down on the gas pedal or not. After two or three times doing this, it would turn over and maintain a steady idle, then off I go.........
The problem now? Well, late today I tried to get it going, and after about 15 times, I gave up. It would not stay idling, it would crank over then die. I did not want to ruin the starter. It seems the gas pedal is worthless after the engine decides to conk out, and no matter how many times I step on the gas pedal, nothing happens.
Has been replaced within the last few months:
Fuel filter regulator,
Inline fuel filter,
Cap and rotor,
Lucas fuel injector cleaner,
ECC computer, and Fuel relay switches, (multi-function relay/connector switch)
Air Control Valve - Removed and cleaned.
Checked all vacuum hoses.
Has not been replaced:
Map Sensor, (was told it's located on Pass. fender wall, but can't find it, according to the manual)
EGR Valve and sensor,
Throttle Position Sensor,
EVP sensor,
Spark plugs, (two years ago)
Plug wires, (two years ago)
Ignition control module, (replaced about six years, or more)
With trying to keep the gas going to turn it over, it does not, so to me, it seems to be more of a fuel problem than electrical, but I'm no mechanic.
View 6 Replies
So I'm sitting in my 99 2.5L at work while we are empty, running the engine for A/C because it's quite hot out. The truck was running for a half an hour or so, not moving, and I look up from my phone at my dash, to see a brand new ABS light on....
So I've pulled out my handy code reader, but no ABS codes have arrived. Maybe my reader can't read it, or maybe I need to drive. But what could this be? And is it safe to drive the truck home tonight? Pedal pressure still feels normal.
View 1 Replies
I have a 2002 Ranger with a 3.0/auto with about 180K on it. It runs good but for the past 6 months I have had a problem starting it. It does the same thing hot or cold but is a LITTLE easier when cold. It is very hard to start, you have to grind the started for about 30 seconds then it starts right up.
I checked to see if I could hear the fuel pump when the power is turned on and yes I can. But after checking the fuel pressure, there is no fuel pressure with the power on and the engine not running. Once the engine starts, there is about 65-68 pounds of fuel pressure - and the truck runs just fine. Starting is the only problem.
I was told I had to replace the fuel pump. Is the electric pump in the tank the ONLY fuel pump on the truck, or does it have a combination of the electric/tank pump and a mechanical pump on the engine?
View 7 Replies
I have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 Replies
My check engine light came on the other morning after a rain storm. I took it to Auto Zone and they put their reader on it and come up with P1633 code. (Keep alive memory (KAM) voltage low).
The next morning the light was off. Couple days later it rained again and the engine light came back. Took it back to Auto Zone and checked it again to make sure it was the same code.
Seems like something might be getting wet unless its just a coincidence that it was raining each time the light came on.
View 1 Replies
Still cant seem to fix this 87 ranger 2.9... NEW fuel reg, fuel press reg, rebuilt computer.cold it will start and run fine.then it will shut down with in 5 to 18 miles then you cant hear the front or rear pumps at all!. Let it sit over night and your off again.. Can't get any codes.. Can a pump over heat and shut both off??
View 14 Replies
Got a problem with the '94 Ranger. Something keeps draining the battery. For reference, the truck is an XL, manual 4x4, 4.0L, 5-speed. I've been trying to keep driving it so I could try and diagnose the issue. At first, as long as I cranked it every day, it stayed charged up, but now it has gotten worse. It will run down in an hour or two. I know figuring this kind of problem out is tough, but I thought maybe some others of you may have experience in this area that might benefit me.
Based on a gut feeling, my first idea was that there was something going on inside the AC compressor. So, I disconnected the compressor, but that wasn't it. My plan at the moment is to replace the wiring harness between the battery and the starter. The current harness is pieced together (not my doing), and whether it fixes this problem or not, it needs to be done. Another thing I've thought about is the ignition switch. It acts "funny" to me, but it has never really given any trouble.
My son needs to take this vehicle back to college with him in a couple weeks, and I need to get it figured out.
View 7 Replies
Engine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 Replies
Although my lil' truck (2006 Ranger XLT, 2WD,with 4-cyl / 5spd, and 115K miles) has been running just fine since I bought it about a year & 5K miles ago, I suspected it still had its original spark plugs and I figured I should change them before problems arrived.
As I suspected, the plugs that I took out looked to be original. I measured their gap and they all had excessive plug gaps - around 0.052" gap. I installed the four new AUTOLITE APP104 (double platinum) and checked their gap, and they were a bit tight at 0.042". My book says they should be at 0.044" gap. But I installed them at 0.042 anyway, figuring they'll burn wider in time.
One by one, I smeared a small bit of never-seize on the plug threads & at the plug-to-cyl head tapered edge. I smeared a dab of Dielectric Grease around at the top of the plug to ease the plug wire re-install and hopefully calm any possible arching. The plug wires came off the plugs easy enough and went back on just as easy.
I hit the key and the engine fired right up. It idled rough as expected. However, it continued to idle rough and if I raised the RPM level, it would respond, but still ran rough. It is throwing a 'Check Engine Light' on the dash cluster now - whereas it wasn't prior to the new plugs.
View 8 Replies
I recently replaced all my incandescent lights on my 99 ford ranger which makes my truck stand out, but the issue I am having is all my exterior lights work including my turn lights but my running lights will not turn on. Is there any way I can fix this problem. I changed my flasher unit with one that is LED Capatable and i added load equalizers to the back to correct the issue with my turn signals but i just cant get my running lights to work....
View 14 Replies
My ranger just started running very rough. Like misfiring, but I think it may be the fuel pump. It starts and drives...but it surges then drives normal, as if fuel is being fed, then starved, then force fed etc. My father asked if I had trouble starting it and to be honest in the last 6 months it was a little harder to start on several occasions. On a few occasions it required more cranking. But that was only a few times.
I tried putting in a fuel injector cleaner and 93 octane gas but it is still running even rougher now. I changed out the fuel filter under the rail about a year ago (maybe 8000 miles ago at most). My father thinks the fuel pump is shot and he laughed because his went on his expedition and he said it is inside the fuel tank and there is no way to get at it without dropping the tank. Is that true? 2002 ranger xl 4cyl
View 7 Replies
So I got everything fixed on my 94 ranger so I thought. Now it runs right on the "L" on the idiot gauge on 90 degree plus days running the AC. Also it seems to lose power at times and not even want to do 70. I think new coils, new plugs and wires may work. I also have an intermittent check engine light that pops up on occasion, but clears when you kill the motor and start it back up. I was really starting to like this truck despite it not being my style(I like square body rangers) and it being a 4 cylinder. I like the MPG but am starting to think the 200k engine may be fading
View 14 Replies
I have a 1996 ford ranger and i have no tail lights i have license plate lights, brake lights, Hazard and turn signals. But no running lights on the rear end. Where the grounds are for this circuit and if some one has a schematic for this ranger...
View 9 Replies
I have a 2006 2.3 ranger motor runs fine at idle and as I ride down the road the motor just cuts off. If I pump gas it will take off again and in 3 miles it will do it again. After 20 miles running good it will cut off again. Replaced coil pack, fuel pump, Cam sensor, Idle control sensor! What else could be causing this?
View 3 Replies
I live in Kansas and was home in Georgia for the last 2 weeks. The truck drove great there after a fuel up started missing and surging at 50 to 70 thought it might have been bad fuel. waited till it was low added Lucas fuel treatment and premium gas still was doing it. no check engine light. went to Advance and fuse for light was blown they checked and was getting mass air flow code. unplugged it and seemed to be better, not perfect but better. plugged it back in and went to do it again. Changed mass air flow night before the drive back to Kansas. Ran well from Savannah to north Georgia then started doing it again the rest of the way home. Going to have advance check code again.
View 12 Replies
I have a '96 Ranger XLT. Just recently the dome light stays on while the truck is running. I have checked both doors and door frames. For the life of me I do not see a switch. The light does go off eventually after the truck is shut off (without killing the battery). What or where is the switch for this light..
View 14 Replies
1998 Ranger 4x4 4.0 Ltr - Runs rough ever now and then and CEL giving P1151 code. Upper and lower intake gaskets have been replaced.
View 14 Replies
2003 Ranger FX4 Flareside
4.0
Automatic
145,000 Miles
Here's my issue: My Ranger has been running like a dream until yesterday.
I took off on a parts run for my sons Ranger. I got to a stop sign and as I stopped, it started missing and barely running. I nursed it back home and checked the flashing CEL. It was giving me a misfire on #3.
Since I had been planning on changing the plugs and wires, I dove in and got it done hoping that was the cause of the misfire.
Started it up, same thing. I went to the next obvious item: coil. Replace it, still running like crap. Gave up for the night.
Today, I thought I would dig in using the tips here on the forum. Did the spray down...no errant spark anywhere. Tested fuel pressure: 65psi no drop in pressure on acceleration.
Started pulling wires off the coil one by one. Four of the wires resulted in running worse. 2 had no effect. #3 and #6. The coil was producing plenty of spark on all 6 ports.
At this point I was sure it had to be 2 bad injectors. Since I couldn't get injectors tonight, I moved them around after cleaning them a bit and tried my wire test again. The problem stayed on the back 2 cylinders!?!
I tested for voltage on the back injector plugs and I am getting voltage. I also used a stethoscope to listen to all of the injectors. The back 2 seem to remain silent. I have also unhooked the battery for 20 minutes to reset the PCM. Still missing and running rough....
Here's a list of what I have done:
Autolite Double Platinum APP5144 plugs. .062 gap
Autolite Pro Series wires #97051
BDW E97P Coil
New air filter
What should I do next? I really don't know where to go next.......
View 8 Replies
1993 3.0 V6 5 Spd ... Changed plugs wires Cap and rotor put in a new idle control Valve. No Check engine light. When i am running down the road feels like it surges,hickups, while its at idle the motor shakes like no tomorrow. Just dont want to throw money at something and not be the part that was wrong. Truck has plenty of pickup runs like a raped ape going down the highway. seems when i accelerate the miss clears up and not there. RPM gauge needle has some movement in it. Also put in K&N filter fuel filter as well.
View 6 Replies
]I recently bought a 1990 ford ranger with a 2.9 @187,000 miles. That being said I went through and changed a few vacuum lines, the oil, air filter, pcv/grommet, and fuel filter.
The problem is it hates to start. I could crank on it for 10 seconds and not a single thing. Sometimes if i turn the key to the off position, wait a second, and try again, Ill get the truck to fire. When it does fire up it just reeks of the lean exhaust. It also gives me some hesitation when I rev it. I did a fuel pressure test (KOEO) last night and it gave me 32 psi and within a minute the needle fell to about 25 psi. I hear the fuel pump run for only 2-3 seconds too.
I've already pulled the MAF off and cleaned it, replaced the TPS, and did a fuel pressure test. The fuel filter is brand new
View 14 Replies
