Ford Ranger / B-Series :: 2006 - Low Humming Sound And Brake Pedal Momentarily Drop Back Just Slightly When Going Downhill
Jan 18, 2014
I recently bought a 2006 Ranger with supposedly 110000 miles... I don't think I made a good deal... because I found the stabilizer end link in terrible shape which seems suspicious for this mileage in my personal opinion!? But this isn't the reason I am posting today... I have a serious breaking issue and I couldn't find explanation yet.
My ABS Light is on. When I slowly brake at low speed and when the brake is almost completely depressed... I hear a low humming sound, and the brake pedal seems to momentarily drop back just slightly. This also happens when I'm going down hill and breaking. For the most part, the car breaks, and it's only every 8th or 10th time braking that I experience this issue.
My guess is this is linked to the ABS... but I can't afford expensive service and need to resolve this on my own.
View 2 Replies
Advertisement
2000 Chevrolet Silverado 1500... When slowing down for stop, when almost stopped, sometimes the brake pedal pushes back momentarily, makes a bit of a (errrr) noise, and for two or three seconds during the push back the brakes do not work. Mechanic has cleaned ABS wheel sensors. All brake pads are good. The truck computer shows all systems okay. All brake lines are new or one year old.
View 2 Replies
2000 Ranger, see my sig.
Just had to swap out the pads on my truck yesterday. The pedal was pretty mushy and I was getting shaking in the steering wheel when the brakes got warm. Shaking wasn't all the time, only after they had been used quite a bit - say after city use and the brakes had to be applied suddenly. So I popped off the tires and swapped out the pads and replaced the brake fluid - flushed it.
On the driver side front, the pads barely had any real wear and the anti-rattle clip was all messed up. It was installed properly, but it looked like the pads had smashed into it. The rotor appeared to be warped, or at least out of round - but just barely. You could see it wobble slightly in one spot if you spun the hub with the caliper removed. The caliper itself was sticking slightly.
I didn't see any evidence of damage, the brakes flushed just fine although the fluid was incredibly dirty (because I haven't done it in a long while). On the passenger side front, the pads were worn down to the level I would have expected given the mileage. The wear was even.
My question ultimately is this - is the out of round hub the culprit here? Might there be something else going on like a caliper problem? Ultimately I plan on having the rotors surfaced - one of them certainly needs it and with new pads I might as well do it anyway.
View 5 Replies
1993 Ranger XLT 4.0 AT. Initially replaced ECM for other problems and then noticed Cruise w/n disengage when brake depressed unless pedal is pushed several times and with more pressure. Put in another ECM and have same problem. Have replaced the brake switch and lights come on as they should. When pedal is pushed the vacuum dump valve on the pedal will dump the vacuum to the servo but when you release the brake pedal the cruise control kicks back in and speeds truck back to set speed.
So this tells me that the dump valve is only a fail-safe feature for when pedal is depressed and does not actually deactivate the servo. Everything else with the cruise works fine: On/Off switch, Set/Accelerate, Resume, Coast. How to proceed next? Like where to find speed control module and how to test it? How to check servo to see if it is getting or dropping voltage that will electrically disengage it, etc? Don't want just throw parts at it. The new ECU's that I used came from ECU Exchange in Florida and there still remains the possibility that they are still the problem.
View 6 Replies
I have a 2008 Ranger Sport 4x4. I noticed yesterday that when I stepped on the brake pedal it felt like nothing was there until I step a little harder then it was like full brake application. The truck only has 63000 on it. Then every once in awhile it would be normal ie very light brake application and slows like it should. Then back to same issue... Any thoughts about this??
View 8 Replies
I have a 2010 Ford ranger sport 4x4, manual, and when backing up at a decent speed, then press the brake to slow up then depress the clutch, the brake pedal pulsates and it feels like something is grinding. It has happened in first once, but I can make it happen in reverse anytime...
View 1 Replies
acts like abs sensors could be bad. but the brake pedal goes almost to the floor, after it does it's pulsating. But the abs light does not come on. I already changed brake booster, no change!
View 5 Replies
So, a few day i bought an 84 Ranger and even since have not been able to figure out what the hell is wrong with the brakes. I know it's not the brake booster for starters. Because, i went to Auto Zone and picked up a new one and when i took the old one off (before i had put the new one on as well) i tried to see if the brake pedal would now move freely and it won't. It is still very stiff and squeaks when you push it down. i then to get it to return have to pull it up with my foot... What it might be? the WD-40 failed here as well.
View 3 Replies
What is the likely culprit? No other electrical issues, brake light quit working when brake is depressed, all other lights work including blinkers/running/head. Was going to break out a wiring diagram....
View 7 Replies
I have a 1990 4x4 ford Ranger, the little truck was purchased in early 2008 as a work truck but has ended up becoming my main vehicle, it has been a good truck for the most part but know I am having some brake issues, well have been having for some time but they seem to come and go. Usually it happens when I have to hit the brakes hard, the rear brakes lock up, I replaced the master cylinder months ago and thought that fixed it, then a month later it happened again. The last time it happened was friday, the time before that was in march 09'.
I have searched this online and found numerous try this but the original poster never comes back to say if the problem is fixed or what fixed it. My ABS light DOES NOT come on when this happens, it does function properly, it illuminates when the key is turned on then goes off. My parking brake no longer works either but I think that is from me "driving thru" the locked up rear brakes. I plan on replacign both drums and shoes within the next week but would like an option to repair the locking up issue.
View 14 Replies
Ok, my question is, when gas pedal is pressed half or more down-ward, a squeal sounding is coming from engine compartment. 2003 ranger v-6 3.0 flex....
View 1 Replies
I have a 2009 F-150 Supercrew. I have noticed that when I am going down a hill and hit a bump with my foot on the brake pedal it depresses and I get a springing sensation from the pedal. It almost feels like I am depressing a spring with my foot and then it comes back to normal ???? Just yesterday I was on an off-ramp of the interstate in a sharp curve and it did it without hitting a bump ???? What is causing this or how to fix it ??
View 1 Replies
I have a 2008 Ford Escape, and today I noticed that while backing out of my driveway (downhill) as I pressed the brake pedal it made this grinding noise, but when I got out of the car I looked through the tires and the rotors and pads were fine. I did not get a chance to check the inner side of the rotor or pad yet. What else could this noise be if it's not the brakes? It only makes this noise when I press the brake pedal which is why I thought it was the brakes.
View 3 Replies
When I release the brake pedal too fast, the brake pedal bounces back with sound which is a little bit loud to me. I feel the sound is from the spring if there's one. It's annoying so I have to remove my foot from the brake very slowly. Is it normal?
View 20 Replies
My 2002 4.0L V6 Ranger, 4x4 overheated *slightly* this past weekend. I added some water and limped it home with a couple stops, trying not to let it get too hot. I since noticed there is oil in the coolant, so jumped to the first non mechanic's assumption the head gasket was bad. I have had (auto) tranny troubles with this truck in the past and started looking inside today and noticed some red fluid under the truck. I think the tranny fluid cools through the main radiator on this one, yes? If so, do I likely have a bad radiator, or is there another likely possibility?
The only wet areas I can find look like where the hard lines come into the right side (looking from the front) back of the rad. If we can determine that, would I need to replace the radiator, or is there any way to plug the tranny lines and run through a separate cooler? I think this also has a tranny, or oil cooler in front of the main radiator but not sure if that is correct, or what exactly that is. This is my daily driver work truck and will bring work to a stop until I can figure it out.
View 5 Replies
I had a friend do an alignment on my truck yesterday. Afterward, we tried to center the wheel the best we could in the shop. But when I drove it home I noticed that when going straight, the steering wheel is ever-so-slightly turned to the right. Is there and easy way to adjust this without me going back to the guys' shop and bugging him again? I know the alignment is dead nuts, but the wheel is just a tad off.
View 4 Replies
My 99 ranger has just hit 111,000 miles. I'm getting a weird sound from the front right whenever I turn the truck slightly to the right. I don't hear it if it's leaning left. Is this likely the wheel bearing? I've heard these rangers are not best known for the quality of the wheel bearings.
View 14 Replies
03, 2.3 duratec, 163k, new timing chain, plugs (AP104), wires and intake. cleaned MAF, air filter, and ran two cans of sea foam through the intake and its still pinging. its driving me up the wall. truck runs perfect but seems to idle slightly higher and take longer to come down to idle after I got the timing chain and plugs/wires done. I've sprayed starting fluid around on top of the engine looking for vacuum leaks but found nothing. What should I try next?
View 14 Replies
I just changed my front brakes in my 05 Ranger. New rotors, pads, bearings (packed), racers, new caliper on driver side, bleed all for brakes. Now when I am just about to stop it feels like the left front is grabbing. I also hear the ABS motor humming when it grabbs. Don't whats causing it?
View 4 Replies
Went from right around 18 to 14-15 last 2 tanks. No codes, drives absolutely normal. I have had my 4x4 lights flashing, but the 4x4 has never worked (suspect its a combination of the transfer case motor and the pulse vacuum hubs). Used to flash like this when I would try the 4x4 switch and would take a while to "get back to where it was happy". Recently I have not messed with the switch or anything else.
View 14 Replies
So, before I noticed a problem, all I had to do was a slight touch to the brake pedal, and the brake lights would come on. Now, they MAY just quickly flash and won't come on unless I really push hard on the pedal, such as at a complete stop.
I've noticed some issues with trying to lock-in 4W-LOW now too, and I know the brake pedal has to be pushed to engage 4W-LOW. Never had problems before now. 1999 F250 Superduty ...
View 4 Replies
