Ford Ranger / B-Series :: 2005 XLT 4.0 - Intermittent No Crank And No Start
Jun 9, 2015
I have a 2005 Ranger 4x4 4.0 automatic with an intermittent no crank, no start issue, So the problem has been getting worse over time This time when it wont start, all of the lights work, the radio, the fan, etc. They are all bright and functioning.
The battery is brand new and showing 12.9v at rest. (Yes, I have tried to jump it and charge it to be sure). However, The gauges are not functioning when the key is turned. I have no click, the lights don't dim, nothing happens when I turn the key.
Another neat point, if I turn on a directional with the key on, the relay clicks so rapidly that it won't even flash the lights. I am assuming that it is a ground someplace, but I dont even know where to start on this truck.
View 14 Replies
Advertisement
This has happened maybe 3 times in the last month. Once merging on to the freeway. Another while cruising 70 in the carpool lane. And the last one I was leaving the job site and it did it.
What I'm talking about is a quick like cut out or stall. Maybe a second of time then back to normal. It also makes a clunk sound. You know these things are hard to describe.
Just don't want to freeze up on the freeway and cause a wreak. Also can I tell from my vin.# if I have limited slip or posi.
Ford Ranger xlt extended cab
2 wheel drive, 4.OL Auto .........
View 2 Replies
I have a 1996 Mazda B2300 & I heard that it is similar to the Ford Ranger.
Well the thing won't crank or start.
This is what I have done so far. I wanted to put a RPM meter on it. I followed YouTube videos on how to do it. I cut the Tan wire w. the yellow stripes & try to connect the wire to thr RPM meter. Then it won't start soo idk what to do. I also took put the PCM too. (I was looking for the wire) Now be honest, I talked to a mechanic, he said thag I might have blown my PCM or Blown another fuse. But when i put the key in to crank, it won't start ot click at all. The lights come on & it wants to start but won't start.
Then my mechanic tried to start it by the... Idk what it is called but you can start it & it wont evet start. It will crank like crazy but will not start at all.
View 1 Replies
94 Ranger, 4.0, Automatic, 280k miles. Normally starts and always runs fine. Sometimes will crank and not start. Fuel pump replaced Feb. 2015 and again Dec. 2016. Have had it towed 3 times. Always starts when it gets to the mechanic. Sort of reminds me of vapor lock on the old cars with carbs, because if it sits long enough after not starting, it will start, no problem. Never died out or even coughed when running and plenty of power. When I take off the gas cap, it sucks in air like a whale. Twice I did that and it will not start right away, but if it sits for an hour or so, it starts no problem. Just bought a new gas cap 10 minutes ago and looked in a Haynes manual and a " gas tank vapor valve assembly" is mentioned. I don't want to change parts just to see what happens. Mechanics say there are no codes shown.
View 1 Replies
I have tried about everything i know about cars on this truck!! It ran great when I got it until a head gasket got blown so I tore into it and replaced them both torqued heads to specs. Made sure valves wasn't to tight. Distributor is in correct spot timing is correct had ignition module tested good!!! Coil tested good replaced both fuel pumps and put new tank and sending unit in the truck b/c it needed it new fuel filter replaced return line firing order is correct 1 4 2 5 3 6 it is getting fire it will crank and crank sometimes act like it is going to start then not also I can get it to run for about 3 sec on 3 or 2 cylinders it seems to have plenty of compression as well!! only thing really I can think of that could be wrong is computer? Also one last detail tried pull starting it as well still wouldn't go.... V6 2.9L...
View 9 Replies
I have a 2005 Ford Ranger Edge 4x4. 4.0, 5 speed. Pretty bare bones truck. On the 4th, my truck was fine... Good deal. On the morning of the 5th, I had a no start issue. No crank, no lights, nada. Figured it's the battery as the one in it was in there when I got it. Got a new one and dropped it in. No difference. This morning I drove me other truck and when I tried to start it this morning I got a clicking in the lower passenger side area. The dash is dark except for the battery and airbag lights, and they're really really dim. This is my newest to me truck and one before this was a 74 Chevy. So computer ones are not my strong point at all.
View 14 Replies
Getting the Banana ready for it's smog test appt at the shop last night (it WAS today) Check engine light had popped on and it had been starting to sputter and surge at the idle occasionally for the last few days so I took a look at the MAF and saw dirty wires. Aha I can fix that, a couple squirts of MAF cleaner, plug it back in and voila! No more light, the Banana ran down the road around the block, over the hill and through the dale like a champ. I shut her down and call it a night.
This morning, hop in and fire the Banana up like usual and all I get is a nice peppy crank over. The Banana has had a bunch (pun intended) of new parts throw at her recently... new battery, starter solenoid, plugs and fuel pump relay and fuel filter. All within the last couple of months.
Out of complete disbelief, I ground on the ignition for a little while and she finally kicked over and sputtered to life. I let her idle a couple of minutes and things seemed fine so off we go. I make it about a block before the Banana starts hiccuping and bucking like something possessed and dies.... kaput.
The Banana has a 3.0, manual transmission and at least half a tank of fuel. Long story short and a tow truck ride home again, half a day trying unsuccessfully to pull a code, any code.... nothing. She will half-heartedly cough and spastically run with ether shots and near as I can tell I'm not getting fuel to the fuel rail relief port. I'm really hoping there is some way to diagnose a faulty fuel pump without having to drop the tank and fish the damn thing out.
I'm not hearing it run when the ignition is turned on but then again I don't think I've ever heard it run. Any other things to try before I replace the pump itself???
View 13 Replies
I have 2000 Ranger 4.0L 4wd, 5sp ...
Just in the last month or so as out temps have been dropping off I've been having troubles getting her started. It happens both when the engine is cold, ie first start of the day, and after starting when warm. It did it a couple times last spring, but then all summer and fall I didn't have any problems (warm outside air temps) but, now its happening again. I'd say any time the Outside air temp is 40F or less, I am worried it won't start. IF i get her to start, everything else is just fine and she runs like a top. Here are the symptoms and what I've done so far.
When I crank I will get a couple cylinders to fire for a second or two then it falters out behaving like fuel starvation. Then I crank again right away and nothing fires... just cranking over and over. If i wait a minute and crank again same symptoms or it will fire right up. Baffling!
I thought Idle Air Control valve and sticking fuel pump relay, so I threw new parts on, but no fix.
About 75% of the time if I turn the key on, hear the fuel pump running, turn key off and on, hear the pump again x3 and then attempt the start it is successful.
Unfortunately, I don't have a code reader, or fuel pressure test equipment. The check engine light is NOT ever on. DO I HAVE A FALTERING FUEL PUMP??? I've heard thats tough to change out.
View 5 Replies
2001 Ranger 3L v6 auto, 186k miles. Never had a problem. One day last month I park it at home. 10 minutes later I need to make a quick trip . Get in, turn key, absolutely nothing happens. Replaced the battery, starter/solenoid, and ignition switch (not the key cylinder lock, but the white box inside the dash below and to the left of the steering wheel...has lots of wires going into and out of it,...turning the key slides a little metal pin inside it up and down). All fuses and relays are good, neutral safety switch is good. Key lock cylinder is mechanically working properly. Engine is not headlights, interior lights, wipers, radio, etc all work fine. Theft light is not blinking rapidly. Headlights do not dim when ignition key is turned. Where do I go from here?
View 2 Replies
1999 mazda B4000 4WD 178000 miles 5 speed manual, I've been having a crank no start problem but after a few tries it would start, a week or so ago it was really cold (23) it wouldn't start so I opened the air box and shot it with starting fluid it took about 5 long sprays but it started.
It ran up op 3200 rpms and won't go back down, took it to my shade tree mech. he hooked it up to the diagnose thing it showed no codes, he poured water over the motor it different places and toward the back it idled down for a second so he says "blown intake gasket' so we replace upper and lower and sure enough we could see where there was a bad spot on the upper and a cleaner spot on the port.
That was not the problem it still idles at 3200, I mean wide open screaming, could the starting fluid have done something? Now he says "blown head gasket" I never had any idle problems before matter a fact besides the hard starting problem that started it was running just fine, what happened?
View 8 Replies
i have a 96 ranger with a 2.3l engine sometimes it will start right up and sometimes it has to crank 4 or 5 times to start i just gave it a tuneup and changed the oil and filter. should i run sea foam through the oil system,it sat for about seven years and i need to convert the idiot gauge to a real gauge.
View 2 Replies
1998 Ranger, 3.0 liter manual transmission. The vehicle recently has had the engine replaced. Still a 3.0 Liter, but possibly is from a 1995 or 1996 Ranger. Replacement motor from a wrecking yard, appears to have been sitting for quite some time prior to purchasing. I had a friend change the motor out after getting the vehicle a few weeks ago.
Ranger drove fine for a week, but this morning it wouldn't start. One click is all it would give when you turned the key. Thinking the culprit was the all in one starter/solenoid, I replaced it with a new one this morning. Now the solenoid will click continuously when the key is turned, starter still will not rotate then engine.
Battery tests good - 12.4 volts; connections appeared fairly corroded.
Here is what I have done:
- Clipped off the first half inch of corroded terminal leads, replaced both sides with new battery connectors and wire brushed connections off at battery and starter.
- Replaced Starter
- With "S" connector disconnected, attempted to bypass starter connections and short terminals to see if a faulty clutch position sensor was to blame; shorting did not produce anything other than turning the key did.
- Paralleled an additional cable from battery to starter terminal to see if corroded wire connections were to blame; still just clicked repeatedly when attempting to start.
Crankshaft does rotate manually, does not appear to be seized up. Unsure of what else to check for. Not confident in friend's engine installation abilities, he may have screwed up something I'm not thinking of. On the other hand, I don't believe I would have been capable of swapping out the motor myself.
View 3 Replies
My mazda b 3000 shut off while at a red light i t turned over initially 3-4 times now nothing. changed EGR, ECM, CRANKSHAFT AND CAM SHAFT SENSOR three weeks ago. brand new battery, took alternator in and it was bad so i replaced. theft light is blinking rapidly?
View 2 Replies
1999 XTL 4.0 auto, was doing fine, replaced Interior light bulb, now wont crank over!!! i suspect the anti theft system... how do i fix or ByPass the security system, i can start the truck by Manually engaging the starter Relay under the hood.
View 1 Replies
I just totally re-built the rear brakes in my 93 Ranger 2wd. Now its seems I have this 'intermittent vibration' between 90 to 105 km/h.
View 7 Replies
My 2.3L Ranger experiences a drawn out 2-3 shift but only does it once in a while. On my drive to work it might do it at 1 of 10 stop/go and the other times it's perfect. It really seams to do it more when it's cold???? I know it's an electronic shift trans so my guess is because it's intermittent it's getting a false signal from somewhere - maybe? All of the other shifts are fine, it just happens 2-3. It has the correct fluid in the trans and is new.
View 10 Replies
It's a 01 Ranger 3.0 V6 5 spd 2wd. He drove home from work then the next morning wouldn't crank over. Turn the key and it doesn't even attempt to crank. All dash lights, headlights, etc come on. Battery is good. Took starter out and tested at parts store. Tested good. Clutch switch was good. Replaced ignition switch with no change. If I jump the solenoid on the starter it will turn the engine over. When turning the key I can hear the starter relay in the fuse block under the hood clicking. All fuses were good. I found the main engine ground wasn't hooked up to anything. I hooked it back up and still nothing. All battery connections were good but cleaned them anyway. Not really sure where to go from here.
View 6 Replies
Ok, basic rundown. Stop at a red light, turns green, when i go it gives a strange grindy-growl from the rear. Lasts maybe 2 seconds then its gone. its very uncommon. But it is something i am interested in getting figured out. Doesn't happen any other time, only on complete stops.
View 2 Replies
2002 3.0, 43,000 miles. Intermittent 'chirping' has begun. Is this the "wear indicator" on the belt tensioner? If so, what is it telling me? And where do I put the breaker bar to slack off tension...Red Arrow, or Blue arrow? They both look like bolts...I was expecting to see a 3/8" square opening...and do I turn clockwise or CCW to slack it all...
View 9 Replies
My '94 4.0L XLT has hesitated to start a couple times lately. Then, after sitting for a week while we were on vacation, the truck would not start at all today.
[URL]
I read about the fuel pump relay, so since I am not made of money, I decided to change that first ($16 vs. $100). After installing the new relay, the truck started! I put the old relay in the box and tossed it into the glove box.
After lunch, and some thought, i decided I wanted to put the old relay back in and see what happened. Guess what! It started with the old relay as well! I also noticed that the humming/buzzing sound the fuel pump makes when the switch is turned on was different with the new relay vs the old one. I put the new relay back in, but now I am unsure where my real problem lies. Intermittent relay, or fuel pump on its way out??
View 6 Replies
I have a 1987 ranger 2.9 V6. Have a intermittent miss @ idle when warmed up. What is the proper way to pull the codes from the computer, i,st something about counting flashes or lights...
View 6 Replies
