Got a 2005 V6 Ranger with low mileage. Having a heater problem. We've replaced the thermostat, heater core, flushed the system twice, burped it to get the air out and replaced the hot water valve. The heater works for a few days then it goes cool: not cold. Adjusting "Temp" will make the temp decrease but it will not return to hot air?
View 2 Replies, my trucks heat selector lever, that controls the temperature in my truck, is stuck in the cold setting. by stuck I mean, I can try to move it, but it wont budge more than about 1/16" and no more. its really frustrating because of the cold weather here, and I want to have SOME heat in my truck without a bonfire to get it.
View 6 RepliesMy wife's 99 Ranger's heater fan is not working. It was working off and on until now. The fuse is fine. I went out this morning and tested the blower motor for power in --had voltage. Assuming the motor was bad, I pulled it. Before wasting $ and a trip to town, I bench tested it --it works. Now my question: what do I do next?
View 6 RepliesI seen on this site awhile ago something about a fix for the heater control door, I have a 1996 Ranger and all I have is Hot heat and cannot cool it down with the temperature control.
View 2 RepliesMy '04 Ranger has over 240k on the odometer. Runs great and has never given me any issues. Everything checks out OK - all the fluids, filters, and whatnot are in good shape. No CEL or any other indication that anything is wrong (except for maybe the IAC valve and clutch slave.)
I've noticed, though, that when I fire it up in the mornings to let it warm up while I scrape the ice and snow off the windows, the heat/defrost will not blow warm air. It doesn't matter how long I let it sit, it will only blow ambient air through the ducts.
When I get going down the road, however, the heat kicks in, after a bit, and works very well!
I've not found anything that would indicate an issue with the blend door or any other component and this is the first vehicle I've had that did this.
Is it normal for a 4.0 SOHC Ranger to do this? Or is there something I'm missing?... It's not really that big of a deal, but I do find it a bit odd that it would do this.
I mentioned the IAC above - I think it's "sticking" every once in a while and, when it does, I'll hear a loud "thump" right before it idles down to around 1k rpm. I can't see how this would affect the heat, though...
Description: It will crank over forever but not start. New timing belt water pump, etc, so it is not timing. tried different fuel pump relay. no luck. new fuse no luck. The radio fuse also shorts and blows when I change it. Headlight does not come on, but the cabin "ding ding ding" sound plays. Marker, turning, reverse, and brake lights work.
CHECK ENGINE LIGHT does not come on during key turn. I may know what caused it or it may not. Before all of this happened, my audio system fuse under the hood blow. It blew again after I installed a new fuse (immediately).
One day, the wires on a portable cigarette light pump snapped and the two wires had been touch. I noticed the truck stalled several times when letting off the gas and coming to a rolling stop. The fuel pump relay makes a click noise when I turn the key
1997 2wd, 4.0 - As you can guess it runs pretty bad at idle. It has O2 heater circuit codes for all 3 sensors. I'm leaning towards the ECM because the 2 heater wires are both hot with the key on. I unplugged the computer and turned the key on and just one wire is hot. Looks like the ecm is supposed to ground the wire to turn the heater on, but it's going hot instead?
View 14 RepliesI have a 1996 Ranger that the Heater/AC blower only works when the outside air temp is above 45 degrees. I have replaced the relay, and the blower motor resistor. What could be causing this?
View 3 Replies2000 Model, The fuse keeps blowing on this. I thought it was the cruise control fuse because the cruise kept not working and when I replaced fuse it would work. Only for a little though, then I looked at manual and it says the fuse is for the brake position switch. I am presuming this is just like the old days and that is the brake light switch under the dash. They use to have two wires now there is like five. Anyways I do not see any bare wires or anything that would blow a fuse, is it common for these switches to go out or what??
View 13 RepliesMy dad's 1991 Ford ranger 3.0 2wd just died on him when he was driving home and I checked to see if the truck had a spark and it did not so I replaced the ignition control module, then ignition coil, then distributor and rotor cap(plug) and I put new plugs and wires on it a few months back too. I also checked to make sure that the timing chain was working as well (while I had the distributor cap off). Then I realized that the EEC maxi fuse was blown. I then found a fourm that said it might be the relay so I replaced the EEC and the fuel pump relays while I had them both out. Every time I put a new 30 amp fuse in the EEC slot and turn the key to start it the fuse blows and the truck won't start. What might be wrong?
View 1 RepliesFound a tee on the heater hose leaks when it warms up. Appears the PO had noticed it but put a hose over it and now is leaking around behind the valve cover. This is a hard plastic line around 5/16. No online parts show it as being available. Is there a fix for this ?
I would bet several others have had this problem as it lays right on top of the flange of the valve cover where I think it would rub a hole pretty quick.
1989 Ranger 4X4 4 cylinder....
I am not great with electrical but can manage. Here's the deal, Ihave a 1997 ford ranger 2wd 2.3L 5spd with a/c 233,000 miles i just replaced the heater blower motor resistor as the old one was rusted bad as was the pig tail going to it bad that one of the terminals broke off and was rusted in the harness so i replaced the plug as well problem is i still have no fan if i jump it it works but have no power at the plug for resistor or motor and no power at the switch inside the truck I do have power to one terminal where the relay plugs in, where to look next?
View 14 RepliesWhen I turn on my heater full blast the most god awful squealing commences. Where to start spraying the grease?
View 10 RepliesThere is always something.... I just drove my girlfriend's new 2003 ranger edge home from the seller. Real nice truck. I noticed the heater selector doesn't change the air flow. It is on full blast for the defrosters, and is also trickling out of the floor and dash vents. No matter where you put the selector, thats the only place the air comes out.
The temp control seem to work OK, when you turn it on cold, you get cold air and visa versa. Even on AC and MAx AC... air out the defrosters. It's cold when you turn the temp control to cold.
I did some searching here and gather some info on checking the vac lines etc. Everything looks in place but one detail. The vac ball under the hood under the air box has 2 ports on the front end, and only one grey line going into it. The other port has what looks like a rubber boot and part of a very short vac line broken off it.
I looked, I cant find any loose vac lines. I'd like to know if this second port is suppose to have a second line on it, and where does it go? What color is it? Is this the reason the vent selector isnt working?
with a new heater core, new blower motor, and new resistor and no heat, what would be the problem? gonna check the thermostat tomorrow.
View 2 RepliesFuse #41 keeps blowing...scan tool says o2 sensor heater circuit malfunction. Problem is that when the o2 sensors are unplugged it keeps blowing fuse the second I hit the key. Where this short would be? I can't find a wiring diagram anywhere. ( I'm new to this forum and I'm sure there is a sticky somewhere..
DTC codes: P1451, P0743. P0750. P0760. P0765. P1747. P0135. P1409. P0755. P0155
'92 Ranger 2WD with 4 cyl and 9" brakes, right rear wheel cylinder keeps blowing out, replaced it twice. I've thought about maybe an obstruction in the left brake line creating too much pressure, or in the junction block on the rear axle. I believe only one line leads to there from the master cylinder, so what else could it be? Only other thing I can think of is that the right brake has a mechanical problem which is causing the forward shoe to move too far away from the cylinder, leaving no 'stop' so the piston just slides right out of the cylinder. But I can't figure that. Original adjuster star wheel was chewed up so I swapped in another, doubt it's that.
View 14 RepliesSince last summer my truck keeps blowing fuse 26 and then I have no reverse lights. If I replace the fust its ok for a bit but blows again the same day sometime. The book says its the fuse for revers and overdrive. The overdrive button on the tree shifter stops working too but the truck does not seem to be revving any higher so I think the overdrive itself is fine. I can't find the short but its got to be shorting somewhere...
View 14 RepliesI recently got a ranger from my buddy and it keeps blowing the EEC fuse in the engine compartment. We have replaced the EEC relay and the EEC power relay. As soon as you turn the key it is blowing the fuse.
View 1 RepliesMy 1996 Ford Ranger's Fuel Pump- Fuse keeps on blowing... (Fuel pump is new)... We need to find where the short is coming from!
View 2 RepliesMy buddy has a '98 B4000 4.0 4x4 Auto, and just recently he lost 4th gear for whatever reason. Which is strange, considering 5th gear still works, and OD requires direct (4th) to work.
So we're thinking its a valvebody problem, and apparently the gasket blowing out of the separator plate is a very common problem. So we decided we're going to drop the valvebody and inspect/replace the gasket.
Now I see that the they now bond the gaskets to the separator plate: What is the part number for this bonded plate?
I've also seen mentions of a TSB, and other mentions of an updated EPC solenoid. Looking for more info on this?