Ford Ranger / B-Series :: 2004 - Won't Start But Cranks Strongly?
May 30, 2016
2004 3.0L Ranger Edge, 88,000 miles on it, I am the original owner. It won't start. It cranks strongly. Usually when this happens, I have to reset the fuel pump inertia switch. This time, resetting the switch does not work. I disconnected the switch and jumped the two wires going to it, but still no start. The switch seems to work ok, in that I can reset it (a ball, spring, and magnet mechanism, I think), then shake it and the ball will come loose.
The fuel pump 20A fuse in the engine compartment is good. The fuel pump relay in the engine compartment is good (I switched it out with an identical relay that runs the fog lights without problem). I am getting spark. I don't have a fuel pressure gauge but pressing in the Schraeder valve on the fuel rail produces gas.
Usually, when the inertia switch is tripped I can get the engine to briefly start by using starter fluid in the air intake. But not this time. I do not hear the fuel pump kicking in when I turn the ignition key to the "On" position, and that would lead me to think that the pump is bad. Except, I don't get a brief start using starter fluid. The fuel filter has never been changed, but again, since I get no start with starter fluid, I don't see how that could be the problem. OBDII scan shows no codes.
View 7 Replies
Advertisement
I have heard from a few people that it might be the computer that is messed up. Just replaced cap and rotor, spark plugs, wires, fuel filters. Pump turns on. Cranks and cranks but won't start. Took the intake cover off and tried starting it, all it did was back fire. Checked the firing order and everything is right. So im left with guessing at the computer and ignition??
View 5 Replies
Ok, went out last night to go over to a buddies place to watch some football. Tried to start my truck but all that happened is that it would turn over, but not start. Had plenty of juice in the battery, and 1/2 tank of gas. It acted like it wanted to start, but nothing doing - just keeps cranking and cranking. Its even more frustrating because I was driving it around most of the day before this happened.
Here's the dillema: Its been doing this for the past two months now on and off. Once I fix something, it runs for about a month, and then it starts doing this again, without any warning signs (i.e. multiple cranks before a start, stalling, hesitation on accel., etc.). At this point I'm clueless. I've replaced the fuel filter, fuel pump, and air filter, but the problem has resurfaced again.
An interesting thing to note is that the only ways I'm able to get it started when it starts doing this is to remove the electrical connection from the intertia switch, and crank the engine a few times to relieve the fuel system pressure. After reconnecting the inertia switch, the truck starts instantly.
So whats the deal? Why this would work, and why suddenly the thing would not start after weeks and weeks of driving flawlessly? Is it possible that my system is either too pressurized or losing pressure somehow, and that is how it be able to start? A buddy suggested it might be injectors, but I'm not so sure, because there is no hesitation on accel or performance loss, or even a rough idle.
View 14 Replies
My 1999 Ranger that I bought used has been serving me well. However, two days ago I went to visit a friend and when I tried to start the truck to go home, the engine cranked but would not fire. I assumed that perhaps I had flooded the engine, so I walked home. I went back an hour later and the truck started up immediately. Then, yesterday, the truck would not fire at all. I towed it to AutoZone to check for error codes, but none were found. I put my inductive timing light on a plug wire and found that there was no spark.
In one instance of cranking, the timing light blinked and the engine tried to fire, but then nothing. The AutoZone man suggested changing the crankshaft and camshaft sensors. I haven't done that yet, but that is my next plan. Can the Ford dealer find error codes that tell what is preventing an engine from starting that AutoZone can't see? For sure there is no spark, but maybe there is no fuel either since I don't smell gas after much cranking. Could it be the inertia switch cutting off both fuel and spark?
View 14 Replies
My kid is using my 94 Ranger with 215,000 miles. It quit while he was on his way to work. Engine cranks but won't start.
Fuel pressure at rail was 12 psi (Key on eng. off). I replaced fuel pump. Pressure at rail up to 20 psi. Still cranks, no start.
I replaced fuel filter. Pressure at rail up to 30 psi. Still cranks, no start.
Replaced distributor cap/rotor and plugs. I have spark at plugs.
Chiltons from 1994 doesn't list a rail fuel pressure. I see new fuel pressure regulators are set at 41 psi. I pulled mine and hooked air to it. It (FPR) cracks at 37 psi. I have lots of flow returning to tank, so I assume the fuel system is working correctly. I've never replaced the timing chain/sprockets. Distributor rotor spins during engine cranking. When I rotate the crank pulley to 0 Top Dead Center the rotor is pointing to #1 on the distributor, so I don't think the timing chain has skipped a tooth on the sprocket??????
View 4 Replies
working on a 84 ranger it did run fine for 3 wks then while driving there was a thump and it stopped and wouldn't start. Now working on it has spark cranks but won't start. while trying to start when I let off the key it tries to catch but only at that time not when the key is turn to start normal. we poured fuel into the carb and it still didn't start. Leaning toward compression maybe?
View 4 Replies
2007 Ranger 4.0.... Initial start of the day it cranks a bit longer than it should. After warm, it starts fine.
View 1 Replies
Removing fuel injectors-coolant contamination.. How is this done? I need to see if they are any good-or clean/replace them-after I accidentally left the clip off the hose running out of the thermostat housing when I drained my coolant last week and the first time I drove, coolant leaked onto the top of the engine/manifold depressions, getting onto and into the fuel injectors.
I tried to clean it up as much as possible the first time(finally got it going) but still a few days later the truck at times cranks but does not start-hot or cold. I assume my idiocy is the cause or maybe it is just coincidence of something else? From what I read from my symptoms it could also be the fuel pump relay, pressure regulator, coolant temp sensor, crank sensor.. among other things. My fuel pump is 1.5 years old, so hopefully that isnt it. Have the injectors possibly been contaminated to where I should just replace them?
View 14 Replies
Made a trip to the hardware store yesterday. When I came out, the truck would crank just fine, but wouldn't start (98 4.0L 4x4). Tried adding gas, no luck. I had actually called a wrecker, but it eventually started after sitting for about an hour. All I did differently was hit the gas pedal a couple of times. Thinking it may be a low fuel pressure problem, I took it to autozone this morning (started it about 4 times now with no problems). Checked the fuel pressure, and it sat at a solid 65 lbs at idle. I tried holding the throttle open and it stayed at the same pressure. I forgot to try with the vacuum off.
First off, I've seen some people say 60 lbs is right, but more say it should be at about 45lbs. 45 seems right since the fuel return is on the block, not on the pump. I'm guessing the fuel damper went out, but is there any good way to check it? Also, since the damper is vacuum controlled, would a bad vacuum cause this problem? Third, could high fuel pressure cause it to not start? That's the one I'm most worried about what was wrong there.
View 14 Replies
i just rebuilt the motor in my 2002 ford ranger 3.0 and it wont start it cranks over but back fires and bucks alot. took the plugs out and it gets spark and fuel. when it sparks it sparks like multiple times.
View 3 Replies
So it often just cranks for 15 seconds before it fires. I put the fuel pressure guage on it and you turn the key on but don't engage the starter it goes to 30 psi then back to 0 in a 2 second time frame. It then stays at zero. when you engage the starter pressure slowly goes up and it starts running while running its a consistent 60 psi.
I presume its the fuel regulator but why does it not go up to 60 psi and why does it just stop with the KOEO? Is it reasonable to just replace the regulator? or should I be replacing the fuel pump to at the same time? I will be doing this from under the truck since there is a lot of hard mounted equipment in the bed.
View 4 Replies
I just finished putting in aftermarket A/C in the 2004 Ranger my dad gave my son. It's a 2.3L, STD transmission. It was running GREAT before the project started. I installed new battery as part of the project. When I started it back up it ran for 2 or 3 seconds then died. I now cranks, but does not fire at all.
I have tried one of the key reprogramming sequences (turn key to "ON" 8 times) with no success. Would it crank at all if it were a key security issue? Is there anything I need to reset anywhere else, like in the air intake system?
It's either not getting spark or not getting air. The fact that it ran for a couple of seconds has me confused. Would it run at ALL if there was a key security problem?
I had to remove and reinstall the air filter housing and ducting. Is there anything else I need to do to with the air intake system?
View 3 Replies
2004 ford ranger 3.0 ... So here it goes I am pretty mechanically incline for the most part i would say until this last week i got a rod knock. So i replaced all my push rods put everything back together and now my car cranks but just wont start up where did i go wrong. I cant afford to get another truck i just want my baby back up and running ...
View 14 Replies
I have a 2001 F350 V10 Crew Cab that has 51000 miles on it so it doesn't get driven all that much, but I do start it at least once a week and it has always started on the first crank.
A couple weeks ago I drove over a friends, I backed up her driveway, turned the truck off and went inside. After returning I went to start the truck and it wouldn't start, just cranked. Probably had between 1/4 and 1/2 full.
I let it coast down to the level and it still wouldn't start. Finally had it towed home. When I got home I tried it and it started right up. Next day it just cranked and wouldn't start. The day after it started right up, I ran it for 20 minutes, turned it off, tried to start it and it just cranked....
Then I started looking at forum's for a possible answer.
I already had an IAC that I bought a few months ago since it was idling a little rough that I installed. Still started intermittently.
When I listen closely when I hear the fuel pump run when I turn the key it starts right up, when I can't hear the pump it won't start.
I have tried moving the relays around that are in the fuse panel on the drivers side hood, moving the fuel pump one to the blower motor and vice versa. Still starts intermittently and only when I hear the pump run.
I looked for the FPDM that in some trucks is up by the spare tire but apparently my truck doesn't have one, or at least in that location..
My next thought is that it must be a bad pump...Can a bad fuel pump act like this, sometimes work and sometimes not?
View 10 Replies
My father in law has a 98 4wd, 4.0L that cranks but doesn't fire. We pulled a plug to check for spark....no spark. Possibly coil pack, or crank position sensor?
View 5 Replies
I have a 1995 ranger with a 4.0 it cranks just fine wont fire has alot of fuel spark it will crank and crack then it stop and acts like it is going to fire up and stops cranking... This thing has 253k on it...
View 4 Replies
My father called me last night to say that his 2004 Ranger, 2.3L engine would not start. He said it cranked over but would not fire. The only other problems this truck has had was a misfire about 6 months ago, which was corrected by a new coil (wires and plugs were changed at that time also).
I looked at it this morning, starting off by cranking it just to see for myself. It cranked fine, stumbled some as if it was trying to fire but never would catch, and I noticed immediately the smell of raw gas from the exhaust pipe. It acted flooded, but injected vehicles are not supposed to flood, so...
No "check engine" light was on, and no codes at all showed on my Actron code scanner. The truck has a half tank of fuel in it, was last filled about a week and a half ago, and was last started about four days ago. It is kept in a garage, currently at about 45 degrees F. It ran fine up until the failure to start last night. I can hear the fuel pump running, and the two plug wires I pulled and checked were firing. I installed the wires back, held the pedal to the floor, cranked it over, and after a few seconds it fired and ran! On the second restart it started a little reluctantly, but multiple times after that it seemed to start fine.
We let it set for an hour or so, went out to try it again, and it would not start again. After I pushed the fuel pedal in just slightly, it fired and ran fine. I repeated this a couple more times while the engine was still cold; no start without touching the pedal, but would start if I cracked the pedal just a little bit. Once started the engine would idle high (1000-1100 rpm or so) for just a few seconds, then idle down as it should when warm.
I'm puzzled by no code, but I'm wondering if the IAC is bad, causing a no-air "flooding" condition if the fuel pedal is not depressed to crack open the throttle plate. That would explain the strong smell of raw gas at first. But, it seems like the IAC is controlling the idle briefly right after the engine starts, but it doesn't seem to be keeping the idle up as long as it should. Would the IAC throw a code if it were not working correctly?
My other suspicion is the TPS, but again without a code I am not sure. My Actron scanner is one of the better models and will read data from the engine; is there a way to check the AIC and TPS function once I do get it running?
View 3 Replies
85 2.0L Dura Ranger.
All of the Idle control wiring and box and sensors have been removed; all else is original. The truck ran just fine after the removal of the above paraphernalia (years). The truck simply quit, no spark at the coil, cranks just fine. All of the wiring has been checked for continuity. The Following components have been replaced with new:
Ignition switch.
Coil.
Dura-spark Box.
Dist coil.
Starter solenoid.
Rotor & Cap.
Plugs and wires.
Correct voltage is present at the coil & D-spark box side of the connector.
Coil tests close to what I think is correct for resistance and the engine ran with it.
I have tested both sides of every connector. I'm not sure what the output side of the D-Spark box (blue tab) voltages should be, and I am unable to test the trigger signal at the coil, however with no output and power in I'm guessing that is the problem...
View 14 Replies
This has happened 3 times.
1st) pulled quickly over to side of road, shut off truck. It would not start then. Towed it to service station and it started the next morning (with no repair made). I wonder if tow ride dislodged the the blockage in fuel line(?). Always sounds like it's going to turn over, but like not getting fuel.
2nd) Went to leave work, truck wouldn't start. Towed to my mechanic and he replaced fuel pump. Thought it was fixed because it ran fine until just the other day.
3rd) Slowed down to complete stop in heavy traffic and it stalled. Would not restart. Again sounded like it was going to start but didn't seem to be getting fuel. Good samaratins pushed me off road. Had it towed to mechanic. Started the next morning without any repair or service. It's like the tow ride and bumps getting it off the tow truck dislodges what ever is blocking the fuel line.
My mechanic replaced the fuel pump, but I don't think her replaced the fuel filter.
View 6 Replies
2004 Ranger Edge 2wd 3.0L. When the truck has been sitting for a while and i start moving forward there is a very loud sound of metal on metal. Changed the diff fluid last week, used royal purple 75-140 with the friction additive. No change, tried to take rear wheels off, but the drums are stuck by the pads. I was able to get the drums off only bout an inch.
Recently, I've noticed that on hard acceleration the RPM go up but it seems sluggish on acceleration. There is also a vibration that comes from the rear and goes away when i remove my foot from the accelerator. The squeal happens between 15 and 20 mph, but goes away fairly quickly. The vibration happens around 40 or so. I am thinking rear axle bearings? But i cant get my drums off to replace the bearings.
View 11 Replies
My 2001 Ranger is used for work to move furniture multiple times in a day. 7 weeks ago, I had moved a dryer w/ it, drove across town for a meeting, got back in & it refused to start & run. The same thing happened 3 days ago on a longer, fuller route w/ a trailer attached. Both times, the truck started & drove home ok AFTER sitting off waiting for my emergency ride. While I waited, I looked up the issue in the owners manual which told me to depress the gas pedal 1/3 to 1/2 & then turn the key in ignition. The first attempt did not work, so I repeated the steps, which started the truck & I was able to drive back. Both times, the truck started no problem the next workday. Does this sound like a problem worth fixing (for the age of the truck vs. cost of repair)? It has pull some weight, including on trailer, in between the two occasions.
View 1 Replies
