Ford Ranger / B-Series :: 2004 Truck Won't Start After Slow Down Or Quick Stop
Apr 14, 2014
This has happened 3 times.
1st) pulled quickly over to side of road, shut off truck. It would not start then. Towed it to service station and it started the next morning (with no repair made). I wonder if tow ride dislodged the the blockage in fuel line(?). Always sounds like it's going to turn over, but like not getting fuel.
2nd) Went to leave work, truck wouldn't start. Towed to my mechanic and he replaced fuel pump. Thought it was fixed because it ran fine until just the other day.
3rd) Slowed down to complete stop in heavy traffic and it stalled. Would not restart. Again sounded like it was going to start but didn't seem to be getting fuel. Good samaratins pushed me off road. Had it towed to mechanic. Started the next morning without any repair or service. It's like the tow ride and bumps getting it off the tow truck dislodges what ever is blocking the fuel line.
My mechanic replaced the fuel pump, but I don't think her replaced the fuel filter.
View 6 Replies
Advertisement
I have a 1995 ford ranger v6 4.0 and for this week Ive been having a problem, stalling... It only happens when I do quick "stop and go" driving. Even sometimes at stop lights it wants to stall, the only way to keep it going is to keep my foot on the gas.
Now for a while when its cold or my truck has been sitting for a day or two the truck doesn't start on the first click.
I've had the fuel pressure checked, changed fuel pump, and starter. I have no check engine light on at the moment. Tomorrow I am gonna check with my scan tool just to make sure. But, it could be fuel pressure regulator, idle air control actuator, egr valve? How I should go along doing this?
View 14 Replies
Sometimes the check engine light comes on and truck will not start,the fuel pump runs non-stop.. when check engine light goes off,the fuel pump runs for a few seconds and stops,truck will start.... driving down the road check engine light will come on and truck runs bad....
View 2 Replies
I noticed that my ABS was engaging when I would slow down to a stop while turning left. I pulled the fuse for the ABS just to make sure that's what was causing the pulsating brake, and it was. Anyway, if it's an ABS sensor problem, would it be the front passenger side sensor if it's only happening when I turn left? Is there a way to test this. Would a scanner detect it? It hasn't been throwing a code or anything. Just the ABS engaging while braking and turning to the left when it shouldn't be.
View 6 Replies
My truck is pulsating when I am coming to a stop, a lot of you all said replace the rotors to which i did and new brakes, shocks. Today I went to get my truck all four wheel alignment done to my truck.. something is not right..
I got my driver tire facing straight, look at the left.. I went back to the alignment shop showed them that, they put it back up there, they called me over and pointed out the machine they use say, it is aligned.. So what is the problem you figure?
To update all I've done to the truck in regards to front end..
rack and pinion
upper control arm
upper lower ball joints
stabilizer inks
rotors (front)
brakes
shocks
When I straighten my left wheel, the right does not look right..
View 4 Replies
My year-old Camry hybrid stalled out last night. It was the second time this has happened. The first time, about a month ago, I made a quick start from a light, followed by a quick stop, both actions to avoid an accident. (I was about to get rear-ended and scooted into the intersection to give the guy closing in my mirror more room.) After the stop, the car had no power but it started up, no problem. Last night, I was about a minute into my trip, stopped at a light, and the power just died. Again, it started no problem.
This time I noticed that the radio went out. Not sure about the headlights. The emergency blinkers came on at the touch of the button before I restarted. In both cases, I stepped on the accelerator and got no power. Took it to the dealer and they couldn't replicate the problem, of course, and whatever interrogation they did of the systems found no faults. They had to be convinced that I knew the difference between an actual stall and just going from gas to electric. It's kind of disconcerting to just stall out in the middle of the street. And I'm concerned that this is a problem that could get worse -- probably just after the warranty lapses.
View 3 Replies
OK- the truck is a early '96 B4000 4.0, 5 speed 4x4. The key could be pulled from the ignition switch in the "run" position (worn key/lock cyl.) I got in the habit of not using the key (never turned the switch to "lock", just "off"). No issues, been driving the truck all over with no key for some time. Now I can't find the key and alarm fob. No worries, I'll just replace the ignition lock/cyl. Done.
Now the alarm is triggered, and I can't stop it. Truck won't crank, either. I assume the no crank condition is the result of the anti-theft being active. I assumed that because I had been driving around with no key, that I did not have a "chipped" key, assuming the truck wouldn't run unless the "chipped" key was in the switch. Since it ran fine, the assumption was no chip. Now I'm not so sure.
What I would like to do is disable the anti-theft/alarm system totally. Pulling the fuse is no good b/c that kills the fuel supply. Is this possible, or do I scrap the truck? I've found 2 sources on the web that indicate that grounding the the green/purple wire that goes into the drivers door will disable the system.
View 1 Replies
Started up my truck today, accel pedal didn't want to move, after giving it some more force it eventually became "unstuck". Now, the real issue I'm having is from a dead stop, in 1st gear, as I'm letting out the clutch the truck boggs down as if I'm not trying to accelerate. I'm giving it as much as I normally would as I'm letting out the clutch but the motor will either die or take a couple seconds before it starts to go. Once I'm moving I don't notice any problems clutching through gears. The check engine light IS on now, however I don't have any diagnostic gear or really any tools for that matter. 1998 2.4L 5-speed...
View 2 Replies
I have a 95 Ranger with the 2.3L and it is a five speed. I am having a starting issue. I have replaced the ignition switch, clutch position switch, starter relay and had the starter tested. The truck will not start with the key. I can jump across the relay and it starts fine but will not even click with the key.
View 3 Replies
So went today and bought a 1993 ranger 4x4 ext cab 4.0! Runs good some bad handy work that i need to fix but truck has plenty of power and good handling...
issue 1- 4x4 not engaging. the light by the push buttons does not come on and you dont hear the "clicking" of the relay trying to engage. so whats the problem and how do i fix it?
issue 2- when clutch is fully depressed and you go to shift (this is only sometimes) you can feel and hear it grind just for a quick sec. and forget about down shifting you cant do that without slowing down. so maybe new clutch?
issue 3- at 65 the vehicle does shake a little otherwise but pretty smooth. any tips on how to smooth it out? maybe new ball joints? tighten some stuff up maybe?
View 14 Replies
I had my battery out for quite some time. When I put in a brand new battery my key was not recognized and my truck will not start.
View 3 Replies
I have a 2002 Ford Ranger, and it wont start at all. Ive replaced the starter, had the battery checked. Not the battery, took starter out, had it checked too, its not the starter either. Someone said it maybe a fuse? This is totally frustrating, and I need to get it figured and fixed asap. Its been going on for weeks., I had it fixed and then it just stopped. It wont even take a jump anymore.
View 4 Replies
i i am having trouble getting the quick connect on the slave cylinder to go back in i just pulled the entire transmission and replaced the clutch and now when i try to put the quick connect fitting in the slave it is rock solid and will not go in at all
View 1 Replies
I have a 96 ranger 4.0L shift lever was very sloppy and one of the torq bolt fell on the floor I used loc tite and tightened them up with no problem put everything back together and now it wont start. I think I checked everything even replaced the neutral safety switch, adjusted the tranny cable, checked fuses and switched around the relays maybe an ignition switch? I am running out of stuff to troubleshoot.
View 13 Replies
My 03 Ranger 4.0L has become a mystery that has baffled every one I know. Everything was fine and I ran home to something from my house was in there maybe 10 minutes came out and the truck wouldn't start. it doesn't even crank over. out of the clear blue. I had a friend who works for a garage check it and he thinks timing chain. Since then I have been told it wouldn't just fall off sitting there with no indication at all there was a problem.
Thought maybe PATS system. Its in order. Put in on a computer from auto-zone and it shows a check engine light but the reading is there is no codes in the computer on file. I am at a loss. Its been months and I really cant afford to take it to a garage right now. Its the strangest thing ever no crank, no stalling just nothing I hit the switch it lights up like its ready to start and nada.
View 3 Replies
Removing fuel injectors-coolant contamination.. How is this done? I need to see if they are any good-or clean/replace them-after I accidentally left the clip off the hose running out of the thermostat housing when I drained my coolant last week and the first time I drove, coolant leaked onto the top of the engine/manifold depressions, getting onto and into the fuel injectors.
I tried to clean it up as much as possible the first time(finally got it going) but still a few days later the truck at times cranks but does not start-hot or cold. I assume my idiocy is the cause or maybe it is just coincidence of something else? From what I read from my symptoms it could also be the fuel pump relay, pressure regulator, coolant temp sensor, crank sensor.. among other things. My fuel pump is 1.5 years old, so hopefully that isnt it. Have the injectors possibly been contaminated to where I should just replace them?
View 14 Replies
My 1990 4.0 refuses to start when the air temperature outside is at approx 40 degrees or below. It will crank until the battery runs dead if I let it. At approx 50 degrees farenheit the truck takes forever to start and always backfires out of the tailpipe and intake manifold (blowing off a hose on the vacuum tree) before it starts. If I can get it to backfire, it will start eventually. If it does not backfire, then I can run the battery dead and the truck still refuses to start. This condition has grown from a little problem to a huge problem over the past 6 months. Here is what I have done so far, including regular maintenance items.......
KOEO test checked OK
KOER test returned code 77 multiple times (TPS).
Replaced Throttle pos. sensor
Replace Idle air bypass valve
Subsequent KOER test came back with no more codes except 11 - OK
Load tested battery
Made new heavy gauge battery cables for + and -
New plugs, wires
newer starter
Changed coil pack for known good one off my explorer
Visually inspected hoses for vacuum leaks, replaced 1 cracked hose
1990 Ranger ext cab 4X2 4.0L, K&N air filter in stock airbox, Pacesetter headers, single 2 1/2" exhaust, stock cat no muffler, 260K on truck, 104K on good used engine from my 1994 Explorer. Purchased Ranger brand new in 1990. A4LD w/ shift kit.
View 14 Replies
I have a 95 Ford Ranger 2.3L with a five speed. I recently had a starting issue were I parked the truck, went into a store came back out and the truck wouldn't start. Figured it was the solenoid as I couldn't jump across it to get the truck to start. Replaced the solenoid. Still no go. Found a fuse in the starting circuit blown. Replaced the fuse and got it started and drove home. Next morning, I go to leave for work and the truck would not start. Got a ride to work came home and checked it over and found the starter locked up. I replaced the starter. Truck started for a few days and now I am having problems again.
Here is the problem I am having now. Starter is good. Proved that as I can start the truck by jumping across the starter relay. Checked the solenoid with a voltmeter and it is doing what it is supposed to do when the truck starts normal. Here is where I am scratching my head. I can start the truck sometimes and it starts just fine. Next time I try to start it, the fuse will blow.
Replace the fuse and it might work for a couple of starts and then the fuse will blow again. I jumped pass the fuse with a piece of wire for diagnostic purposes. Out of 20 starts, it only started normally 4 or 5 times. I have checked every wire I can see under the dash and have not found any obvious issues. I am at a point where I am so frustrated that I just want to push this 400k mile truck into the back forty and put it out of its misery like a lame horse.
View 9 Replies
I have a 91 Ranger 4cyl. Tune up about 2 months ago. Mileage about 178,000. When the temperature gets below about 45 degrees, the truck will not start. It cranks like the battery has plenty of juice but refuses to start. Once the temp warms up, the truck will start first crank.
View 5 Replies
Installed a new clutch and slave today. Kept the same master cylinder.
The problem I am having is that the clutch pedal will not go to the floor, and therefore the truck won't start. The slave is moving back and forth roughly 3/8 inch, maybe more. I am pretty confident that there is no air in the system.
If I loosen the pressure plate a little, the clutch will go to the floor. But tighten it back up, and it again only goes down about 75%. This is a late '95 so it has the self adjusting clutch. I did get the correct kit for it, as well as slave. It's like the self adjusting part is too far adjusted and won't let my slave travel as far as needed.
In troubleshooting, I did notice that I failed to get the dowels in the flywheel aligned in the pressure plate. I am old school and not used to dowels in the flywheel! The dowels are not hitting anything and are not preventing the pressure plate from seating on the flywheel. But it is something I'm going to fix if I have to pull the trans again.
For reference, I replaced the clutch because the slave cylinder was hanging up and preventing the clutch from getting fully released. Aka clutch slipping.
View 6 Replies
I have a ford ranger 1996 4 cylinder. The truck was driving fine then all of the sudden it shut off and wouldn't start... I checked spark and that is fine also changed fuel pump and made no difference. We also sprayed lighter fluid and that did nothing. It sounds like it wants to start but wont.
View 10 Replies
