I have a 2004 Ranger 4x4, 4.0, auto and have trouble with the back brakes howling, locking up and generally driving me nuts. I've replaced the drums, shoes, cylinders, emergency brake cables and all the hardware. We've bled all 4 numerous times, blown out the lines, looked for leaks and done all we can think of. What am I missing?
View 1 RepliesI just had new shoes, hardware, wheel cylinders, drums, leaf springs, rear shocks, and shackles put on. The brakes were done about 4 or 5 months ago and the springs and shocks just a few weeks ago. The rear brakes were locking up after I had the work done, but I thought they were just too tight. I loosened them a little but it only worked a little.
Now it's starting to lock up pretty much every time I apply the brakes. The ABS kicks on and the rear tires skid. I took the drums off today and didn't see any leakage or anything out of the ordinary. They weren't too tight and I readjusted them but they weren't out of adjustment much if at all. I looked at the Ford symptom chart and it says for brakes that lock up easily there could be sticking or binding components. I didn't see any. Then it says check parking brake components.
Now I see they didn't hook up the equalizer bracket that goes to the front leaf spring hanger when they changed my springs so I assume thats why my parking brake pedal goes to the floor. Then it says check the shoes and linings, which are fine. The last thing it says is to check the fluid control valve. Which I'm guessing is the prop valve.
The only way to check it according to Ford is swap it for a known working valve. One person told me that it could actually be a bad brake booster check valve. Is that possible? Anything else that's common? It's got 272,000 miles on the frame but everything's been changed that typically wears out at least once.
I have a '99 Ford Ranger XLT 2WD. I've been having this problem with my rear brakes locking up on me while slowing down and pressing the pedal to stop the forward movement. There are four components which could cause the problem. My OEM Ranger Repair Manual suggested to replace the Proportional Control Valve which I did however that did not correct the problem. I don't have the Brake nor the ABS Warning light coming on and they check out OK during the start up. I have no problems braking from any speed except when coming to a stop. I inspected my front disk and the rear shoe brakes and they seemed to look OK. The other components which could cause the problem are the Control Module, RABS valve and the Speed Sensor. My question is: If any of these components malfunction, shouldn't the ABS Warning Light come on?
View 2 RepliesI've got a 1997 Ford Expedition 5.4 with 200,000. So my rear differential leaks a few drops of fluid every time I drive it, looks like it's coming from the pinion seal. I've just been filling it topping it off with fluid.
Anyway, yesterday I got in it and started driving, I noticed a howling noise, and when I turned my rear tires started locking up. It was like that for about 5 miles until I got home, no matter which way you turned the tires would lock up.
I went under and topped off the differential with fluid again, and I pushed my parking brake in and released it. Got back in the truck and drove, and it was fine. What happened? I'm just worried it will happen again if I don't look more into it.
Received the truck, 1989 Ranger XLT long bed single cab from my mom. It had been used by my younger brothers for some years, and then sat at mom's for a couple years.
It needed new front brakes badly, so replaced rotors, and pads. No unexpected problems there.
Looked at replacing the rear. Both adjuster cables were initially broken, so they obviously weren't adjusting, or braking. Replaced with a hardware kit, and shoes, and drums. Its the 9" drums, BTW.
Still not actually braking. I can tell this, when at a stop sign in the winter, with the brake pedal held down, and the backs will still spin, with the tranny in D. Even on gravel or grass, this'll happen.
One shop told me this is because the axle seals are leaking. THey've never leaked badly, and the axle fluid isn't low, by and shade of the imagination. Also, this theory falls apart, when the parking brake works just fine, right? Its just hydraulically that they don't work.
I've since replaced the wheel cylinders, the brake line from the frame to the rear axle, and the master cylinder. No change. Bleeding them doesn't seem to be a problem; i.e. no lack of or little fluid witnessed, it seem fine.
Also have bypassed the RABS valve for about a year or so, and its made no difference. Last fall I pulled the drums off, and manually adjusted them, and it didn't seem much better either.
I have a 1990 4x4 ford Ranger, the little truck was purchased in early 2008 as a work truck but has ended up becoming my main vehicle, it has been a good truck for the most part but know I am having some brake issues, well have been having for some time but they seem to come and go. Usually it happens when I have to hit the brakes hard, the rear brakes lock up, I replaced the master cylinder months ago and thought that fixed it, then a month later it happened again. The last time it happened was friday, the time before that was in march 09'.
I have searched this online and found numerous try this but the original poster never comes back to say if the problem is fixed or what fixed it. My ABS light DOES NOT come on when this happens, it does function properly, it illuminates when the key is turned on then goes off. My parking brake no longer works either but I think that is from me "driving thru" the locked up rear brakes. I plan on replacign both drums and shoes within the next week but would like an option to repair the locking up issue.
Last week I had to replace my tailgate handle while in the middle of moving. It was nice that it was easy, but it was a major hassle in the middle of a move! In light of having to do this, I was wondering if there are locking handles available, and if so what might you recommend?
View 4 Replies2004 F250, I am getting this howling noise when applying the brakes. It sounds like it is from the left front and is more prevalent when applying the brakes down an incline (off ramp, etc) I pulled the wheels off and the pads were probably 50-60% worn. I bought some new pads and installed them and I still get the same noise. I didn't buy the cheap pads, nor the most expensive either. Either way, I can't figure it out. Would I need new rotors? I would think I would have some vibration if the rotors were warped. My other thought was the caliper, but when I replaced the pads it compressed fine and I lubed the slide rails. Not sure what to do at this point. The truck has 94,000 miles on it, FX4, Lariat, Crew Cab, and it has the 5.4L in it.
View 2 Replies2004 automatic 88,000 miles 2wd
When I bought the truck it had a very small oil leak that would drip out of the bell housing between the housing and the inspection pan. it would leave a quarter (25cents) sized stain on the ground and would only drip for 10 minutes or so after I shut it off. in 3000 miles it would be down 1/2 quart of oil...
Well 3 weeks ago I stopped and noticed a HUGE stain now. I checked the oil and was 1 quart low. I filled it then I drove 90 miles the final week before parking and was down another 1/2 quart...
I am figuring the rear main seal is gone. I did some research and it seems these are common to go in the 3.0? What seal is the best to get? should I get the seal right from the dealer? or I will run into the same problem and go with a after market? I also learned that the crank shafts can get a groove in them and it's good to put a new "speedy seal" where can I get one of those?
Also for some strange reason I take the tranny out and the rear main is good ( I seriously doubt it) is there anything else that could be leaking that I should check when I have the tranny out? Can I remove the tranny with the factory exhaust still in place? it looks like it can squeeze just by it?
I've recently noticed a howling sound coming from the rear end of my f150 from speeds of 45-60mph it goes away as soon as i get to 60mph and starts again very slightly at 80mph. I am sure its the pinion and ring from everything I have read online. a friend told me that it could be the pinion gear is worn out or it needs re shimmed or something. what parts should I look for to get this fixed? could it be a fluid issue? I dont want to have to spend much more on this truck....I love it but it seems like i find a new "noise" every week. Ive always been a chevy guy and to my surprise I REALLY like driving this truck and i want it to work out. What should i expect to pay for a repair like this? BTW it is and 04 FX4 with 84k on it.
View 14 Replies2004 Ranger Edge 2wd 3.0L. When the truck has been sitting for a while and i start moving forward there is a very loud sound of metal on metal. Changed the diff fluid last week, used royal purple 75-140 with the friction additive. No change, tried to take rear wheels off, but the drums are stuck by the pads. I was able to get the drums off only bout an inch.
Recently, I've noticed that on hard acceleration the RPM go up but it seems sluggish on acceleration. There is also a vibration that comes from the rear and goes away when i remove my foot from the accelerator. The squeal happens between 15 and 20 mph, but goes away fairly quickly. The vibration happens around 40 or so. I am thinking rear axle bearings? But i cant get my drums off to replace the bearings.
I'm having a problem with my rear drum brakes locking up when I press the brake pedal. I've had this problem before, but ignored it because it wasn't too bad. It would just release after taking my foot off the brake pedal.
1998 F-150 XLT supercab 4x4 front discs, rear drums 4.6L v8 175k miles
I cleaned my master cylinder and bled all brake lines so they have fresh fluid. Now that my brakes work way better, my rears just lock up. I put new brake cylinders on, still locking up. I went to a junkyard today and replaced the proportional check valve, brakes still locking up.
Could I maybe have did something wrong when cleaning the master cylinder? I'm sure I put it back together correctly. Anything else i should look at? bad lines maybe?
I replaced the master cylinder 2 months ago and now every now and then the rear lock up for a second. its only happened a couple of times. Pulled the wheels and everything is in place with nominal wear with clean drums and rotors. Am at a loss as to why this is happening.
View 1 Repliesmy front brakes have been locking up here recently. I think it my be due to a blockage in the resovior. I had taken it apart upon the first spell of it locking up, had my buddy press the brake pedal a few times with the lines from the res disconnected and it seemed to be be a little clogged at first and then freed up once it was stepped on hard a few times. So i reassembled the system and bled the brakes out and it seemed to be fine for about 70 miles or so. Then out of no where it started locking up once again.
View 4 RepliesI have a 2006 Saturn Vue that has an intermittent problem. After commuting for 50 miles and parking for the day, when I leave to go home by pulling forward out of the parking space, there is a loud metallic clang and the left rear wheel locks. When I step on the brakes to stop the car stops, but the rear wheel stays locked. When I press the brake pedal all the way down about half way down there is a difference in pressure on the pedal and the rear wheel releases. This will repeat up to three times. Has also happened after the 50 mile drive and stopped at store for 20 minutes. Will not repeat every time, and of course not when there is a mechanic is anywhere near the vehicle.
View 1 RepliesI had to replace the tie rods in my mazda b2300 and the mechanic also replaced the brake pads.
Now when I drive, I can hear the pump for the brake fluid going on and off when I'm not even using the brakes and the ABS goes on a lot too.
He tried resetting the computer by unplugging the battery for a bit but it's still doing it.
Little back story, truck sat up for 2 years. Had 1/2 tank of gas in it that time. I had to do a complete motor swap. I been driving for past couple of days. Had it stall on me while I was waiting on wife to come out of store. Thought it was just bad gas. Today I was heading to town and had to slam on brakes and it started to stall again. It shut off. I cranked it back up and it runs fine till I start slowing down. then it wants to die.
I can keep my foot on gas petal and little and it will stay running. I got to where I was heading and put it in park and it idled fine for a few seconds and then I could hear a whine from the fuel tank. Sounds like the fuel was having a hard time, like it was fighting the pressure build.
Thing is It cranks right back up and drives fine as long as I dont come to quick stop or set idling for a few seconds. I can hear the pump straining, so I am assuming that when I keep my foot on gas a little the pressure is staying lower and not as much is being bypassed and the pump is fine. I think the pump is on its way out but wanted to hear what yall think.
I do have a brand new IAC valve that I bought and did not get a chance to use on the blown motor.
I tried to explain this to a garage in January with no luck. When it is raining I hit my brakes and my truck jerks like whiplash. Softly hitting brakes doesn't do it, normally hitting them does it (only in the rain), I had some welding done after I went to the garage.... They fixed the front passenger side now it feels like it is under me and it is now doing it when I brake in reverse too... I bought it October 2012 and it was safety inspected until October 2014. Trying to decide if it is worth keeping. I want to keep it but when I go to a garage they see dollar signs. It only acts up when it's raining. And I had the welding done in January and it was fine, until I got new tires last week.
View 12 RepliesOn deceleration with the brakes (not coast to slow) I get a growling. Sometimes a bit worse than others. Seems to get worse coming up to about 20mph from speed. No other time. I was thinking front wheel bearings as the load up from deceleration. But I just jacked it up and could not find anything that felt or sounded wrong. No play or grind or "bad" feelings in either of the fronts. Front end recently rebuilt, new tires too.
View 9 RepliesI have a 2007 ranger and when applying the brakes i get a vibration, I think it may be in the rear of the truck but it is hard to tell.
View 2 RepliesAll I did was take wheel off to tap a stud and I saw the inboard pad shim came off. So I removed the shim and reinstalled everything and the wheel is severely pulling to the right. Yesterday I took the caliper off but did not take off hose, cleaned slide pins and lubricated with anti seize. Still pulling to right bad. Don't hear any squealing or grinding. But pass side wheel is definitely hotter than drivers side. One mechanic said he thinks it would be a bad hose before replacing caliper. What could it be?
View 8 Replies