Ford Ranger / B-Series :: 2004 - Rear Axle Noise When Start Moving Forward
Dec 4, 2013
2004 Ranger Edge 2wd 3.0L. When the truck has been sitting for a while and i start moving forward there is a very loud sound of metal on metal. Changed the diff fluid last week, used royal purple 75-140 with the friction additive. No change, tried to take rear wheels off, but the drums are stuck by the pads. I was able to get the drums off only bout an inch.
Recently, I've noticed that on hard acceleration the RPM go up but it seems sluggish on acceleration. There is also a vibration that comes from the rear and goes away when i remove my foot from the accelerator. The squeal happens between 15 and 20 mph, but goes away fairly quickly. The vibration happens around 40 or so. I am thinking rear axle bearings? But i cant get my drums off to replace the bearings.
View 11 Replies
Advertisement
I have a 1995 ranger four letre 5sp, dubbed Beula. I figured there'd be a few gremlins and there was and is, which I know to be more common than not in older trucks. The top priority is figuring out why when I push the lever for the high beams forward, the headlights cut out completely, whether in gear or not, and I don't know where to begin troubleshooting. I've surfed around the forums looking for answers and really only found conjecture.
View 14 Replies
The rear axle in my dads 1998 ford ranger has been vibrating for quite a while so I pulled the cover today and found that the fluid was full of metal shavings, it was glittering. I also found this metal chunk in the differential so my mechanical experience tells me this is not a good thing. I am taking it apart tomorrow any tips or do's or don't? Also, what this metal chunk is and what that knurled up end is??
Door tag told me it was a 7.5 open 4:10 axle.
View 14 Replies
Really noisy rear with leaking axle seals. Looking to swap in a "yard" unit. Mine has 10" shoes. The door sticker says it's a code 86 rear. If I look for a ranger with a code 86, will everything be the same?
View 5 Replies
Today I took the bed off of my 99 ranger. I was sitting on the cab looking down at the rear axle noticed the drive shaft was not entering the rear diff perfectly straight. As I looked further into it, I noticed the distance between the rear spring on the passenger side tire, is noticeably different. To visualize it, the wheel, at the bumper side of the axle, has a shorter distance between it and the leafs than the cab side. Not massive, but a few inches, and it's noticeable now that I can stand over it. I'm beginning to be very annoyed by this truck and it's previous owners, whom I take it , scammed my brother quite well with a $5k tag for a truck with so much not right with it. It's about to become my yard art for awhile.
View 8 Replies
Will move if n 4low and give some rpm's. Reverse is fine, disassembled and clutches look fine.
View 1 Replies
2000 ranger v6 automatic trans electronic 4wd shift on the dash. Plowing snow all of the sudden lost both forward and reverse never slipped or made any noise. Transmission fluid is fine to the level and clean. Put in drive nothing and reverse nothing put it back in park you can hear the park paul trying to click in. Towed it back to the shop thinking maybe the transfer case was junk. Decided to check the actuator on the transfer case no power going to it, go back to the switch no power there either check the fuses both are good and have power. The question i have is could a bad GEM module cause all this? ps the windshield wipers do work.
View 6 Replies
Did I get bent over? had a banging noise coming from the rear and took it to my regular shop, they told me the leaf spring shackle and hanger brackets were almost rusted thru and one more pothole and I'd be all over the road, so they ground out the rivets and replaced said brackets. I don't have the equipment to do that kind of work but I still feel it was a little high.
View 1 Replies
2001 4.0 4x4 auto trans... Problem, tranny judders when coming to a stop moving at around 3-4mph. Engine drops to around 500rpm and maybe one second later returns to normal as the tranny seems to disengage. No judder or shifting problem when accelerating.
View 5 Replies
2004 automatic 88,000 miles 2wd
When I bought the truck it had a very small oil leak that would drip out of the bell housing between the housing and the inspection pan. it would leave a quarter (25cents) sized stain on the ground and would only drip for 10 minutes or so after I shut it off. in 3000 miles it would be down 1/2 quart of oil...
Well 3 weeks ago I stopped and noticed a HUGE stain now. I checked the oil and was 1 quart low. I filled it then I drove 90 miles the final week before parking and was down another 1/2 quart...
I am figuring the rear main seal is gone. I did some research and it seems these are common to go in the 3.0? What seal is the best to get? should I get the seal right from the dealer? or I will run into the same problem and go with a after market? I also learned that the crank shafts can get a groove in them and it's good to put a new "speedy seal" where can I get one of those?
Also for some strange reason I take the tranny out and the rear main is good ( I seriously doubt it) is there anything else that could be leaking that I should check when I have the tranny out? Can I remove the tranny with the factory exhaust still in place? it looks like it can squeeze just by it?
View 7 Replies
I have a 2004 Ranger 4x4, 4.0, auto and have trouble with the back brakes howling, locking up and generally driving me nuts. I've replaced the drums, shoes, cylinders, emergency brake cables and all the hardware. We've bled all 4 numerous times, blown out the lines, looked for leaks and done all we can think of. What am I missing?
View 1 Replies
I have a 2000 ranger 3.0,automatic 4x4.The truck will not go forward in drive 1 or in drive. If I start out in second gear it will shift through the other gears. What the problem is?
View 6 Replies
My 4x4 4WD Ranger has a 5 speed manual tranny that locks up after going forward a few feet. It can back up all day long but locks up going forward. some god awful noises (grinding, clunking, etc) come out of that gearbox. the 4wd is electrically operated. the ? is , can this tranny be rebuilt with a kit? I'm having great difficulty finding a replacement. Are bronco II's compatible? Engine is 2.9L V6. On disassembly I found 2 meshing gears with broken teeth.
View 5 Replies
1988 Ranger, 2.9, 5 speed, 2wd, 7.5, 3.42:1, 190K or 290K on the odo.
I've been hearing this rattling, sometimes kind of a metallic ping, from the rear the last week. I thought it was probably the universal joints, didn't do it often, only under load between 1500-1900RPM roughly in second, third and fourth. I planned on working on it this weekend.
Today it started really making noise, sounds like valves rattling as though the timing was too high but it was coming from the rear end. It was making it all the way through the gears into fifth, even when cruising. Once it cooled down a bit it nearly went away.
I'm going to get started on it as soon as I can, but I can't get it in the shop to pull the differential cover and take a look right now. Dad's shop is full of crap, I live on top of a hill, not many safe places to get one up in the air properly. What is causing that sound?
View 5 Replies
My Ranger has 296,000 miles on it. Most everything has been replaced except the u-joints. It's a 2wd 2.5L with an automatic. The motor was replaced at 228,000 with a used motor with 52,000 miles. The transmission has about 60,000 miles on it. All the bearings in the rear end were replaced about 20,000 miles ago. It has the most annoying whistling noise coming from the rear only sometimes. I don't know if it's the brakes being misadjusted or a bearing with a burr in it. It happens at random times but it's such a high pitched whistling you know everyone on the road can hear it too. There is also a driveline vibration, very minor though when over 60. However, I've had the drums checked and even had the wheels balanced many times. My friend said the ujoint grease could be dried up, but the whistling noise only happens at random, the virbation is anytime you're at highway speeds. It's not a violent vibration just enough to tell that it's not a brand new truck anymore. What it could be?
View 2 Replies
Noticed with the colder weather that when I first start moving and turning tightly, (lets say out of a parking space both backing out or pulling forward) there is a sound coming from the rear end that sounds like a heavy treaded mud tire rubbing on an inner fender. Tried to read up on it and most posts say change your Haldex fluid, but unfortunately I haven't found a thread that says whats happening. I haven't changed the fluid yet and will. (it is at 16,430 since the last change so its getting close as is). When I engage the parking break one click the noise instantly goes away. Am I hearing clutch chatter, pump going out, just dirty or low fluid?
View 5 Replies
Some family members borrowed my truck, and when they returned I have a loud whining noise coming from the rear axle, which I have determined is a 9.75 rear. I checked oil level and it was high enough, but has a slight leak from the pinion seal. Everything feels solid but I have nothing to compare it to.
Its on a 2005 Super Cab with the 5.4L 183,000 miles. The front pinion seal was replaced in Feb 2 years ago, by the dealer's mechanic, who may have been a shade tree mechanic.
I am a Youtube Certified Mechanic, as in, I watched about 10 videos of people working on their 9.75 differentials, and realize I don't have all of the tools to do the job, such as a press, or race drivers, or the special gauge.
How many of you have tackled this issue? What did you find? What am I looking at for cost? I am on a very small budget.
View 5 Replies
I have a 1994 Honda Accord EX AT. Recently, while I am stopped at a Stop Sign or a Red Light, the car will suddenly start moving forward causing me to apply more pressure to the brakes. It also feels that the brake pedal is traveling a lot further now.
View 3 Replies
Have a 99 Ranger XLT, 4 cyl, manual transmission with 191K miles. Was running good as ever last night but went to start it this morning and throttle's stuck open, causing truck to move forward when in 1st gear. Even with clutch in, near impossible to get vehicle in or out of gear. Managed to get it into reverse, but truck was having none of it. What is the cause or causes of my trouble? Or how much the repairs might cost? I'm on the road so no chance of doing this myself.
View 2 Replies
2004 3.0L Ranger Edge, 88,000 miles on it, I am the original owner. It won't start. It cranks strongly. Usually when this happens, I have to reset the fuel pump inertia switch. This time, resetting the switch does not work. I disconnected the switch and jumped the two wires going to it, but still no start. The switch seems to work ok, in that I can reset it (a ball, spring, and magnet mechanism, I think), then shake it and the ball will come loose.
The fuel pump 20A fuse in the engine compartment is good. The fuel pump relay in the engine compartment is good (I switched it out with an identical relay that runs the fog lights without problem). I am getting spark. I don't have a fuel pressure gauge but pressing in the Schraeder valve on the fuel rail produces gas.
Usually, when the inertia switch is tripped I can get the engine to briefly start by using starter fluid in the air intake. But not this time. I do not hear the fuel pump kicking in when I turn the ignition key to the "On" position, and that would lead me to think that the pump is bad. Except, I don't get a brief start using starter fluid. The fuel filter has never been changed, but again, since I get no start with starter fluid, I don't see how that could be the problem. OBDII scan shows no codes.
View 7 Replies
My father called me last night to say that his 2004 Ranger, 2.3L engine would not start. He said it cranked over but would not fire. The only other problems this truck has had was a misfire about 6 months ago, which was corrected by a new coil (wires and plugs were changed at that time also).
I looked at it this morning, starting off by cranking it just to see for myself. It cranked fine, stumbled some as if it was trying to fire but never would catch, and I noticed immediately the smell of raw gas from the exhaust pipe. It acted flooded, but injected vehicles are not supposed to flood, so...
No "check engine" light was on, and no codes at all showed on my Actron code scanner. The truck has a half tank of fuel in it, was last filled about a week and a half ago, and was last started about four days ago. It is kept in a garage, currently at about 45 degrees F. It ran fine up until the failure to start last night. I can hear the fuel pump running, and the two plug wires I pulled and checked were firing. I installed the wires back, held the pedal to the floor, cranked it over, and after a few seconds it fired and ran! On the second restart it started a little reluctantly, but multiple times after that it seemed to start fine.
We let it set for an hour or so, went out to try it again, and it would not start again. After I pushed the fuel pedal in just slightly, it fired and ran fine. I repeated this a couple more times while the engine was still cold; no start without touching the pedal, but would start if I cracked the pedal just a little bit. Once started the engine would idle high (1000-1100 rpm or so) for just a few seconds, then idle down as it should when warm.
I'm puzzled by no code, but I'm wondering if the IAC is bad, causing a no-air "flooding" condition if the fuel pedal is not depressed to crack open the throttle plate. That would explain the strong smell of raw gas at first. But, it seems like the IAC is controlling the idle briefly right after the engine starts, but it doesn't seem to be keeping the idle up as long as it should. Would the IAC throw a code if it were not working correctly?
My other suspicion is the TPS, but again without a code I am not sure. My Actron scanner is one of the better models and will read data from the engine; is there a way to check the AIC and TPS function once I do get it running?
View 3 Replies
