Where to start looking to resolve this code. It is not an intermittent code. It returns after about 3 to 4 key turns. Truck idles a little rough but runs fine. I have looked up the code and causes but wondering how to deal with this directly and fixed it. I'm wanting to sell my truck for something bigger and would like to solve the issue before hand. 2003 Ford Ranger Edge...
View 4 RepliesA buddy of mine has a 2003 Ford Ranger Edge V6 3.0L, he got the code P1450 the other day and asked me to look at it. Got all the info on what it could be but where ex actually is the EVAP canister and CV solenoid located? And what is the problem?
View 1 Replies1999 ranger, 2.55 speed. truck idles with very high rpm's when driving and shifting gears. have changed the AIC, mass air sensor. Throttle position sensor and still does it. the AIC has been changed 5-6 times in 6-8 months as parts store kept telling me it was that. What can i look at, check, etc...
View 6 RepliesI have a 96 ranger with the l4. Right before I bought my newish truck last December, it's started miss firing and running really bad. I replaced the spark plug wires, most of the spark plugs, and both coil packs. Didn't work at all. Then I bought my new truck and parked. Fast forward to now. Fired it up, ran REALLY bad. We changed the wiring order from the 96 order to the 99 order.
But the truck idles from 500rpm (barely running) and randomly jumps up to 2-3000rpm and then back down. Driving it has NO power, rev it and it stays at 2-3000 for quite awhile. Sometimes it randomly dies. REALLY need to get it running quick and cheap. Getting ready to sell my daily driver to find something else and I need something to drive while I hunt for another truck.
Quick back story I bought a 1999 Ford Ranger It is a 4 cyl with an auto trans the guy said it had some trouble with the tranny (major understatement) he also forgot to mention he cut out the CAT. so running a 4 banger off the header.
When you start the truck it rough idles but you have to hold the gas down til it warms up. You can shift into reverse but it labors the motor and the motor will not up the rpms kinda stays at idle and wants to die no matter how hard you accelerate and you can't move up a slight incline.
When you shift into drive you have to rev the motor to 3 grand an it will catch then move slowly forward. no matter how high the revs go. The fluid levels are a tad above the full level and a bit dark for my liking.
Ok, I used an OBDII scan tool from the parts store and it came up with 3 codes P0351, P0352, P0500. From my internet search the first two seem to be coil related which explains why the motor is running like garbage. The last may or may not have to do with what the tranny is doing.
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 RepliesHad to put a new tranny in my 1997 F150 XLT Lariat 4x4 5.4 liter engine about 3 weeks ago and now have gotten the check engine light. Took it to autozone and code 1450 was the only code listed. They said it was was a vacuum problem, but when I checked the code at a web site it is listed as a secondary air injector system circuit shot to B+.
My question is which is correct and how to repair?
I'm having a bit of trouble with my fathers '03 Ranger Edge 4.0L. It has about 100k miles on it, and we keep it very well maintained. This is the first major problem we've had with it.
When the problem first occured, it had been driven about 30 miles on the highway and about 5 miles after getting off the highway, he pulled up to an intersection and stopped. As he started accelerating again, it all of a sudden started sputtering, surging (almost exactly as if it were running out of gas), and then stalled. It continues to exhibit this behavior. It will start and idle fine, but struggle and then stall when given any amount of throttle. It's also an automatic transmission if that makes any difference.
Fast forward to this past week after we had it towed home. We have checked the fuel pressure, and its dead on at about 64psi. We changed the fuel filter, changed the PCV valve, changed the upstream O2 sensor, put in a new air filter, cleaned the MAF sensor, and cleaned the intake of the throttle body. We're now at a loss as to what could be causing the problem. The CEL is not on, and there are no codes being shown when we plugged it in. We also thought it may have been bad gas, so we drained the tank and put fresh gas in from our preferred station. The plugs and wires are also fairly new, only about 4k miles on them.
Are we missing anything here? What else we could try? The absolute last resort is taking it to a shop, we're going through a rough patch with finances.
Although my lil' truck (2006 Ranger XLT, 2WD,with 4-cyl / 5spd, and 115K miles) has been running just fine since I bought it about a year & 5K miles ago, I suspected it still had its original spark plugs and I figured I should change them before problems arrived.
As I suspected, the plugs that I took out looked to be original. I measured their gap and they all had excessive plug gaps - around 0.052" gap. I installed the four new AUTOLITE APP104 (double platinum) and checked their gap, and they were a bit tight at 0.042". My book says they should be at 0.044" gap. But I installed them at 0.042 anyway, figuring they'll burn wider in time.
One by one, I smeared a small bit of never-seize on the plug threads & at the plug-to-cyl head tapered edge. I smeared a dab of Dielectric Grease around at the top of the plug to ease the plug wire re-install and hopefully calm any possible arching. The plug wires came off the plugs easy enough and went back on just as easy.
I hit the key and the engine fired right up. It idled rough as expected. However, it continued to idle rough and if I raised the RPM level, it would respond, but still ran rough. It is throwing a 'Check Engine Light' on the dash cluster now - whereas it wasn't prior to the new plugs.
Ok, I replaced the head gaskets on this truck a couple years back and now I am having symptoms similar to the ones I was having then. I am not entirely convinced that this is what is wrong however.
Symptoms:
Truck was idling rough until it warmed up
Truck takes forever to warm up or simply does not warm up
If/when it warms up it operates at higher than normal temp/almost overheats(it hasn't overheated yet)
Heater blows very cold air
White smoke(has been cold outside so not sure if due to temp or coolant)
Overflow bubbled when I shut the truck off, but it has only happened once so far
I am kind of at a loss, but like I said am suspicious of the head gaskets.
So my "farm truck" is idling very rough, to the point that sometimes that it stalls out. At high idle it runs fine but when its at a idle its very rough. Its been running fine until probably a month ago or so and its just getting worse. What it could be? I am thinking it might be that something is dirty but i just dont know where to start with figuring out what the problem is.
View 9 Replies1990 Ranger 2.3L 4 cylinder. The truck idles so rough it dies. It runs fine going down the road it just seems to "load up" at idle. I know there are hundreds of things that it could be, I just hate to start throwing parts at it. It is definitely running rich at idle.
It is one of those trucks that we have replaced a lot of parts. The scan tool said something about setting the timing??? Is there a way to set the timing? There is no distributor, and it is the one with 2 coils and 8 plugs.
1998 Ranger 4x4 4.0 Ltr - Runs rough ever now and then and CEL giving P1151 code. Upper and lower intake gaskets have been replaced.
View 14 RepliesI have a 2006 Ford Ranger with the 3.0L v6. The check engine light came on and the code it is blowing is a P0171. It runs rough at idle or when I let off the accelerator and "fine" at speed.
The code told me to check/clean the MAF which I have done. Next on the list that I saw was the PCV valve. I disconnected the electrical to it and then disconnected the hose. Some oil poured out of it... not a lot but some... The valve still seems free, it clicks when I rotate/shake it and I can blow through it (I know, highly scientific). I can replace this (if I can find it, Napa and Advanced Auto don't have a part that looks like it...) but I'm wondering what else could be wrong.
I have a 98 ford ranger with a 3.0 v6 it has 228,000miles standard tranny but I keep the truck running great. I did the plugs and wires about two weeks ago and it was running fine, actually great. This morning I got into the truck to start it this morning and it barely started. It fired up but barely stayed idling. I would get into the petal and it wouldn't raise rpms. I had to get to school so I headed out. I couldn't get any speed in gear the truck wouldn't gain speed. It would sputter and pop and then all of a sudden it would go ok but then start popping again. I took it to a buddy shop and his scanner showed p1131 and p1151 both codes. I don't know what to do?
View 13 RepliesI bought this from my brother in better than mint condition. Always maintained. Its generating a cyl #2 misfire code.
It starts and runs like new when cold, but when it warms up, it idles rough, and generates the code. after 1500 rpm it smooths right out and runs fine.
He had it to the dealer just before I bought it and they told him needed a new engine.
I am thinking bad injector, since what seems to be happening is, when cold it gets more fuel, or when u rev it gets more fuel, but at an idle and warm, it doesn't seem to be getting enough maybe. And I see from the maintenance records, a couple of other injectors have been replaced as well.
I think the dealer got tired of replacing injectors under warranty and tried to milk him for a new engine.
2002 ranger extended cab 2wd, 3 door, 232,000 kms 5 speed 3 liter V6, new glass and clutch..
2000 4.2....Last year I had to replace the coil pack when it started running rough and had a code for a misfire on cylinder 3. It is doing the exact same thing now, same code, same cylinder. Is there something wrong that is causing this?
View 5 RepliesI have an 03' Ranger and I assume it has the BW 1354 tcase. I am getting a "clank" sound when the truck shifts from 1st to 2nd. I am thinking its the rear output yoke on the t case. I can grab it and move it up and down but there is no fluid leaking or anything. Would this be a rear bearing problem?
View 2 RepliesMy 03 Ranger 4.0L has become a mystery that has baffled every one I know. Everything was fine and I ran home to something from my house was in there maybe 10 minutes came out and the truck wouldn't start. it doesn't even crank over. out of the clear blue. I had a friend who works for a garage check it and he thinks timing chain. Since then I have been told it wouldn't just fall off sitting there with no indication at all there was a problem.
Thought maybe PATS system. Its in order. Put in on a computer from auto-zone and it shows a check engine light but the reading is there is no codes in the computer on file. I am at a loss. Its been months and I really cant afford to take it to a garage right now. Its the strangest thing ever no crank, no stalling just nothing I hit the switch it lights up like its ready to start and nada.
168K, to date, replaced
rear 2 cat's
Timing chain and gears
cam sync assem.
Plugs, wires, dis block,
Why.............. Read on
This 2003 ranger 3.0 v6, run very hard at idle, yet it runs and you can drive it around town, ""at"" low rpm, and no hills but it gets from point a to point b
I have no pre ingintion, but a plug that was only 60 days only was burnt out completely on 3rd cyl. bank 1 or as ford call it #3, i am telling you this thing seem like it running on 4 cyl,s kicking back and forth, and replacing everything above made no difference.
On the highway, as long as it is flat or down hill 75-80 mph, as soon as a hill or power to pass is needed it bogs down and slows it self to about 45 mph, I have been though everything i can think of and my next move to to start pulling heads, but i wanted to ask here first.
2003 Ranger FX4 Flareside
4.0
Automatic
145,000 Miles
Here's my issue: My Ranger has been running like a dream until yesterday.
I took off on a parts run for my sons Ranger. I got to a stop sign and as I stopped, it started missing and barely running. I nursed it back home and checked the flashing CEL. It was giving me a misfire on #3.
Since I had been planning on changing the plugs and wires, I dove in and got it done hoping that was the cause of the misfire.
Started it up, same thing. I went to the next obvious item: coil. Replace it, still running like crap. Gave up for the night.
Today, I thought I would dig in using the tips here on the forum. Did the spray down...no errant spark anywhere. Tested fuel pressure: 65psi no drop in pressure on acceleration.
Started pulling wires off the coil one by one. Four of the wires resulted in running worse. 2 had no effect. #3 and #6. The coil was producing plenty of spark on all 6 ports.
At this point I was sure it had to be 2 bad injectors. Since I couldn't get injectors tonight, I moved them around after cleaning them a bit and tried my wire test again. The problem stayed on the back 2 cylinders!?!
I tested for voltage on the back injector plugs and I am getting voltage. I also used a stethoscope to listen to all of the injectors. The back 2 seem to remain silent. I have also unhooked the battery for 20 minutes to reset the PCM. Still missing and running rough....
Here's a list of what I have done:
Autolite Double Platinum APP5144 plugs. .062 gap
Autolite Pro Series wires #97051
BDW E97P Coil
New air filter
What should I do next? I really don't know where to go next.......