I have an 03 Ranger 4.0 4x4 5 speed. It has no power, can't give throttle or it bogs real bad. Baro shows 18in vac with KOEO. When running it has 15in vac. Replaced MAF, fuel pump, and fuel filter.
View 4 Replies1986 Ranger 2.3 inline 4
I just recently bought an 86 Ranger from a friend. It had recently stopped working and had no desire to fix it. So here I am. The truck will sit in park and rev all day long, once its in drive it idols fine and moves its self down the street. The problem occurs when I apply throttle. It begins to bog down and I cannot get past 20mph. I have replaced the fuel regulator and also I took the tank down and replaced the fuel pump. The fuel filter is two months old, and the throttle response sensor is two weeks old.
Two days ago, I was driving on a North GA steep, windy, mountain road in my 2002 v6 4.0 Ranger. All of a sudden, i started revving real high (about 4000rpms) and getting no power (20mph). I pulled over immediately and transmission fluid was pouring, by the quart, out of my truck. I didnt get to look exactly where it was coming from, since i backed away once i saw a small flame coming from the leak. i then called a tow truck (assuming it was a seal or a hose break) and had it towed to my house.
I started investigating the possible problems and didn't really see anything noticeable under the truck (not that I was expecting to). So what I did was put three quarts of transmission fluid in the dipstick hole and put in gear to see if I could spot a leak. nothing. then I drove it around the block to get it warmed up and put a little pressure on the transmission by driving up a semi-steep hill to see if that would spark the leak again. still no sign of the a leak.
And finally, when I went to go check the dipstick after my test drive, it read to be above the cross hatched area, hence being overfull. What my next step should be?
I have this 03 3.0 flex fuel that as of lately (2 months) has developed a whistle when throttle is pressed half way or more.... not sure what or where its coming from..
View 2 RepliesMy 2000 ranger in 4x4 high never did this. And in 2wd it doesn't pull at all...
When in 4x4 high it pulls hard to the left ?????? is left not working? It has automatic hubs ...
I have a 2000 ranger 4.0l 4x4 automatic transmission 5r55e. When I put it in drive I don't have any problems except in do it starts jerking when I give gas. When I put it in reverse I can move but as soon as I give gas it stalls the engine tranny was sitting in another truck swapped it with mine I changed the filter and 5 1/2 quart of oil.
I when to a transmission shop plugged it inn no codes and he said he would changes all solenoid and valve body gasket but he's not sure what is the problem. So I started to take out valve body and notice the oil is darkish red and was wondering if it was normal or not and if I'm taking that valve body out for nothing or should still go ahead ...
I have a 2005 ranger, 3.0 and automatic trans
The truck runs fine until it is warm... runs great down highway... stopping at a light or stop sign is horrible, It will act like the (old term ) carb is flooding out.
I put it on a meter It said tps so I replaced it. then it said number 4 cyl no power so I put new plugs in.... I do not hear any vacuum leaks, and It runs like a top when cold.
I have a 1985 ranger 2.3l efi and it bogs and dies while while driving, it can sit and idle all day long but when you go to drive it, it works great for 3-4 minutes then out of nowhere starts bogging sometimes I can keep it going a little longer but in the end the truck always dies . I know I'm loosing fuel pressure , I hooked a gauge up to it and drive it down the road when the truck died it showed 10 psi , from here I'm lost . It has a new fuel pump in the tank and I can hear the other one running when I click the key on , Also two new fuel filters .
View 3 RepliesIf I hop in my truck right now (1994 3.0 ford ranger 5 speed) as soon as i accelerate half pedal or more it'll bog down really bad. Usually in second gear it does it the most and ill shift to third gear and it still jerks and has trouble accelerating. If I let the car sit for 10 minutes and then go drive it it'll jerk and bog down a little bit but no where near as much. usually only does it for the first couple minutes of driving then goes back to normal. I also noticed that my temperature gauge is always right before NORMAL. Also I'll have to give it a little more gas right before i go to drive or it'll want to stall but as soon as i get into driving it, it acts perfectly fine.
View 7 RepliesI have an 87 ranger, 2.3 4cyl. 2wd 5 speed. When I start up the truck after it sits for a few hours it will idle fine but then it starts to bog down and wants to stall but after about 5 mins its fine and runs like a champ. I don't know if its a sensor or what.
View 2 RepliesStarted up my truck today, accel pedal didn't want to move, after giving it some more force it eventually became "unstuck". Now, the real issue I'm having is from a dead stop, in 1st gear, as I'm letting out the clutch the truck boggs down as if I'm not trying to accelerate. I'm giving it as much as I normally would as I'm letting out the clutch but the motor will either die or take a couple seconds before it starts to go. Once I'm moving I don't notice any problems clutching through gears. The check engine light IS on now, however I don't have any diagnostic gear or really any tools for that matter. 1998 2.4L 5-speed...
View 2 RepliesI am currently working on a 97 ranger with a 4cyl and 5 speed. its having some idle issues that i cant seem to pin point, you can start it and it will idle rough then when you rev it up it chugs real hard then dies. used my scan tool and all the sensors are good, fuel pressure is good, good compression, all 8 plugs are firing good and no codes. The other deal that has me a little confused is when I unhook the hose that runs from the air intake tube to the valve cover, I get a lot of vacuum at that port on the valve cover that the hose hooks to. Also when I plug it and pull the dipstick, I get vacuum at the dipstick tube. never seen this before but at the same time I've only messed with very few of these trucks so I don't know whats normal.
View 6 Replies1999 Ford Triton V-10 engine, after changing Oxygen sensors, all vacuum hoses and Mass airflow sensor,(also replaced another sensor but can't think of the name of it right now) now I don't get the codes but engine will start and idle but if I give the engine gas it bogs down and stalls. Vehicle sat in my driveway for 3 months, I got it started and drove it once about 30 miles filled up my gas tank thinking gas could be stale, but now it will not run.
View 5 RepliesI have a new problem that I only discovered a few days ago. As I come to a stop at a traffic light, turning out of somewhere or whatever if I give the car a little more gas than normal not that I punch it or anything from a stop the car bogs down and bangs a little rough like I was rear ended. The car is in drive when it happens. Its just fine any other time. I was told it could be as simple as a bad tps or as bad as a defective torque converter or tranny. Its a 2005 gls hatchback with the 1.8L. also, the engine has been running a little rough recently too if that could have anything to do with it. No warning lights are on either.
View 15 RepliesI have a weird issue. When I'm running AC on my 2.3l ranger sometimes the idle wont go down but rather hold its current RPMs till i either turn the AC off or place the truck back in gear. What that could be?
View 6 Replies1999 Outback 2.5, idles fine but bogs or loss of power when stepping on throttle. Can "feather" or tease to get going and will hold rpm once it gets there...
View 5 RepliesI have a 2002 Ranger 4.0 4x4 Off-road. Over the weekend I started hearing a squeaking sound that varied with the throttle, so I guessed the u-joints needed work. I took it in (no garage or tools available atm), and the garage called me later in the day saying my driveshaft was unrepairable, that I needed a new one. I told them to hold off.
Now, a little research found me some sites claiming that Ford did indeed make some disposable driveshafts, with pinned u-joints, but in the F-series, not the Ranger.
2002 Ranger XLT 4WD 4.0.. I was passing another car at about 55 when they also started speeding up (go figure) so I floored it and got on around them but before I lifted I felt it miss, the CEL began flashing so I slowed to the speed limit and went on to work. The light flashed for about a mile then went out. So on the way home I floored it again close to home and the CEL came on again. Got home and put the code reader on it and all it had was a random misfire so I have cleared it. The truck has new plugs, wires, etc for a complete tune-up. I don't usually run at full throttle so don't know if that would be normal for the Ranger, the Ranger was my wife's truck for 12 years and now is my DD. Need to clear this up? Thought of changing the fuel filter in that is still the original one.
View 8 RepliesMy ranger is an 89 but it's got a 91 motor in it, 2.9 V6. When I accelerate it hesitates before actually accelerating which makes me think the TPS is bad. Probed and tested and I got .85V throttle closed and 4.65 at wide open. Specs call for .8V - 4.5V
I'm not sure if there's an allowance of fluctuation, but is that high enough to point out a bad TPS? If it's not the TPS, is the ignition timing off or what else could it be?
4.0. I'm having what feels Like a Miss on Light throttle/cruise. Once warmed up it's fine. Idle is fine too. There is No CEL/Codes.
View 14 RepliesIt first started with a huge lose in power (can't rev over 3,500 rpm or get over ~55 mph) and a pig on gas! P0125 showed up so after looking for a while I figured I would change the sending unit
- Single wire (3F1Z-12A648-A), coolant temp sensor (ECT I believe) to PCM
- Two wires (F7DZ-10884-AA) and then the thermostat.
- Throughout this time the heater worked perfectly fine. The temperature gauge would get up to C but never very far from it. I would never get to the middle.
In doing so I drained the coolant took off the intake hose (cleaned the butterfly valve in the process) then got clean access to the sensors and the two 10mm screws for the thermostat. I got it all off and apart just fine minus the one stubborn plug on the sending unit (single wire). Putting the sensors back in took more effort then taking them out it could have been the anti-seize or thread sealant that came on it. Anyways, I also noticed that BOTH the new sensors I picked up from the dealership looked identical. Both of them looked similar to this:
Granted the tops were different colors but the ends (metal) were the same or at least I couldn't tell the difference. The ones I took out of the block were definitely different. The sender (single wire) looked like the one above but the sensor looked like this with the pointed tip (I can upload pictures too):
I put the coolant temp sensor in first (two wires) and the plug went on fine. Put the sender (single wire) in and I couldn't get the cap on... it was too tight. I looked at the old one and it seemed like one of the ribs to guide the plug on was off by the thickness of the rib... I tried again and thought maybe it was me and eventually cracked the cap.
Now the coolant gauge doesn't work at all doesn't even move. I then got it scanned and saw P0117 come up... Is this for the sender (1 wire) or the sensor (2 wires). Also I read that once P0017 comes up it could be difficult to start the truck... I thought it was because there was gunk left over from me cleaning the butterfly valve but that may be it instead.
My questions are... Did I mix the sensors up? I really don't think so I double checked before I put them in that only one was open at a time. Was I given the wrong sensor for the coolant temp as it looked different at the tip? I have no clue? Looking at threads for P0117 it seems to be the sensor. I will be going back to Ford tomorrow am to take the old ones in to check. Why wouldn't the plug fit on the sender (single wire)?... I have no clue.